Hobart DP-3035 - Manuals - manualsarea.com

Page 2 - From Hobart to You; Register your product at:; Protect Your Investment!

Hobart Welders manufactures a full lineof welders and welding related equipment.For information on other quality Hobart products, contact your local Hobartdistributor to receive the latest full line catalog or individual specification sheets. To locate your nearest distributor or service agency call...

Page 3 - TABLE OF CONTENTS

TABLE OF CONTENTS SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1. Symbol Usage 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1...

Page 5 - ELECTRIC SHOCK can kill.; FUMES AND GASES can be hazardous.

OM-230 261 Page 1 SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING som _3/05 Y Warning: Protect yourself and others from injury — read and follow these precautions. 1-1. Symbol Usage Means Warning! Watch Out! There are possible hazards with this procedure! The possible hazards are shown in the adj...

Page 6 - WELDING can cause fire or explosion.

OM-230 261 Page 2 Arc rays from the welding process produce intense visible and invisible (ultraviolet and infrared) rays that can burn eyes and skin. Sparks fly off from the weld. ARC RAYS can burn eyes and skin. D Wear an approved welding helmet fitted with a proper shade of fil- ter lenses to pro...

Page 7 - ARC WELDING can cause interference.

OM-230 261 Page 3 1-3. Additional Symbols For Installation, Operation, And Maintenance FIRE OR EXPLOSION hazard. D Do not install or place unit on, over, or near combustible surfaces. D Do not install unit near flammables. D Do not overload building wiring − be sure power supply system is properly s...

Page 9 - Symboles utilisés; Dangers relatifs au soudage à l’arc; UNE DÉCHARGE ÉLECTRIQUE peut

OM-230 261 Page 5 SECTION 2 − CONSIGNES DE SÉCURITÉ − LIRE AVANT UTILISATION som _3/05 Y Avertissement : se protéger et protéger les autres contre le risque de blessure — lire et respecter ces consignes. 2-1. Symboles utilisés Symbole graphique d’avertissement ! Attention ! Cette pro- cédure comport...

Page 11 - LE RAYONNEMENT HAUTE; Proposition californienne 65 Avertissements

OM-230 261 Page 7 2-3. Dangers supplémentaires en relation avec l’installation, le fonctionnement et la maintenance Risque D’INCENDIE OU D’EXPLO- SION. D Ne pas placer l’appareil sur, au-dessus ou à proximité de surfaces inflammables. D Ne pas installer l’appareil à proximité de produits inflammable...

Page 12 - Principales normes de sécurité; Information EMF

OM-230 261 Page 8 2-5. Principales normes de sécurité Safety in Welding, Cutting, and Allied Processes, ANSI Standard Z49.1, de Global Engineering Documents (téléphone : 1-877-413-5184, site In- ternet : www.global.ihs.com). Recommended Safe Practices for the Preparation for Welding and Cut- ting of...

Page 14 - -3. Connecting Spool Gun To Handler 210; Correct; Gun Fully Seated

OM-230 261 Page 10 3-3. Connecting Spool Gun To Handler 210 804 695-A 1 Drive Assembly 2 Spool Gun 3 Gun Securing Thumbscrew 4 Gun End Loosen thumbscrew. Insert end through opening until it bottoms against drive assembly. Tighten thumbscrew.Spool gun must be inserted completely to prevent leakage of...

Page 15 - -4. Installing Wire Spool And Threading Welding Wire

OM-230 261 Page 11 3-4. Installing Wire Spool And Threading Welding Wire 804 697-A Tools Needed: 1 Thumb Screw 2 Spool Cover Remove thumb screw and spool cover.3 Hub Tension Nut 4 Wire Spool Install spool so wire feeds from top. Turn hub tension nut just so a slight drag is felt on the wire spool.5 ...

Page 19 - Trouble

OM-230 261 Page 15 5-3. Changing Liner Ref. 804 687-A Tools Needed: Y Turn Off power at welding power source first. 1 Nozzle 2 Contact Tip 3 Liner Remove and replace liner.Reinstall parts as shown. 1 2 3 5-4. Troubleshooting Trouble Remedy Gun tube assembly loose. Tighten nut at base of gun tube ass...

Page 20 - A. Before You Start Welding; How heavy depends on the output capacity of the welder being used.; B. Welding Techniques; Side View Of Gun Tip Angle; amounts of spatter and smoke.

OM-230 261 Page 16 5-5. GMAW (MIG) Aluminum Welding Hints Here are several hints to help you be more successful with your new aluminum feed system. MIG welding aluminum requires different techniques than MIG welding mild steel. A. Before You Start Welding S Material thickness that can be welded with...

Page 23 - Notes

Page 28 - Hobart Welding Products; Please complete and retain with your personal records.; To locate a Distributor,; Contact your Distributor for:; Resources Available; For technical assistance:

PRINTED IN USA © 2006 Hobart Welding Products. 2006 − 01 Hobart Welding Products An Illinois Tool Works Company 600 West Main Street Troy, OH 45373 USA For Technical Assistance: Call1-800-332-3281 For Literature Or Nearest Dealer: Call 1-877-Hobart1 Model Name Serial/Style Number Purchase Date (Date...