Hitachi ED-A220N - Manuals

4 WARNING Be careful in handling the light source lamp. The projector uses a high-pressure mercury glass lamp made of glass.The lamp can break with a loud bang, or burn out. When the bulb bursts,it is possible for shards of glass to fly into the lamp housing, and for gascontaining mercury to escape ...

5 Safety Precautions (continued) CAUTION Be careful in moving the projector. Neglect could result in an injury or damage.• Do not move the projector during use. Before moving, disconnect thepower cord and all external connections, and close the slide lens door orattach the lens cap.• Avoid any impac...

7 Safety Precautions (continued) NOTE About consumables. Lamp, LCD panels, polarizors and other optical components, and air filter and cooling fanshave a different lifetime in each. These parts may need to be replaced after a long usagetime.• This product isn’t designed for continuous use of long ti...

8 • If the lamp should break (it will make a loud bang when it does), unplugthe power cord from the outlet, and make sure to request a replacementlamp from your local dealer. Note that shards of glass could damage theprojector’s internals, or cause injury during handling, so please do not try toclea...

9 Regulatory Notices FCC Statement Warning This device complies with part 15 of the FCC Rules. Operation is subject to the followingtwo conditions: (1) This device may not cause harmful interference, and (2) this devicemust accept any interference received, including interference that may cause unde...

2 Contents Introduction . . . . . . . . . . . . . . . 3 Features . . . . . . . . . . . . . . . . . . . . . . 3Checking the contents of package . . . 3Part names . . . . . . . . . . . . . . . . . . . . 4 Setting up . . . . . . . . . . . . . . . . . 7 Arrangement . . . . . . . . . . . . . . . . . . . ...

3 Introduction • Keep the original packing materials, for future reshipment. Be sure to use the original packing materials when moving the projector. Use special caution for the lens. NOTE Introduction The projector provides you with the broad use by the following features. Checking the contents of ...

4 Introduction (1) Lamp cover ( 89 ) The lamp unit is inside. (2) Control panel ( 5 ) (3) Elevator feet (x 2) ( 23 ) (4) Remote sensor ( 16 ) (5) Lens ( 94 ) (6) Intake vents(7) Filter cover ( 91 ) The air  lter and intake vent are inside. (8) Battery cover The internal clock battery is inside. (9)...

5 Introduction Control panel (1) STANDBY/ON button ( 18 ) (2) INPUT button ( 20 ) (3) POWER indicator ( 18, 98, 99 ) (4) TEMP indicator ( 98, 99 ) (5) LAMP indicator ( 98, 99 ) Buttons ŻŹŸź (6) FOCUS + / - buttons when no menu is displayed ( 24 ), or Cursor ◄ / ► buttons when a menu is displayed ( 2...

6 Introduction Remote control (1) VIDEO button ( 21 ) (2) COMPUTER button ( 21 ) (3) SEARCH button ( 22 ) (4) STANDBY/ON button ( 18 ) (5) ASPECT button ( 22 ) (6) AUTO button ( 24 ) (7) BLANK button ( 27 ) (8) MAGNIFY - ON button ( 26 ) (9) MAGNIFY - OFF button ( 26 ) (10) MY SOURCE/DOC.CAMERA butt...

7 Setting up Install the projector according to the environment and manner the projector will be used in. Setting up (continued on next page) Arrangement Refer to the illustrations and tables below to determine screen size and projection distance. The values shown in the table are calculated for a f...

10 Connecting with your devices (continued) • When AUTO is selected for the COMPUTER IN1 or COMPUTER IN2 port in COMPUTER IN of the INPUT menu, that port will accept component video signals ( 40 ). • When the USB TYPE B port and the computer's type A USB port are connected, you can use the USB TYPE ...

12 Connecting with your devices (continued) Setting up • If you insert a USB storage device, such as a USB memory, into the USB TYPE A port and select the port as the input source, you can view images stored in the device ( 77 ) . • You can connect a dynamic microphone to the MIC port with a 3.5 mm ...

13 Connecting with your devices (continued) To use network functions of the projector, connect the LAN port with the computer's LAN port, or with an access point that is connected to the computer with wireless LAN, using a LAN cable. To use NETWORK BRIDGE function, also connect the CONTROL port and ...

14 Setting up Connecting to a power supply 1. Put the connector of the power cord into the AC IN (AC inlet) of the projector. 2. Firmly plug the power cord’s plug into the outlet. In a couple of seconds after the power supply connection, the POWER indicator will light up in steady orange. ► Please u...

15 Using the cable cover Utilize the cable cover as the guard and blind for the connecting parts. 1. Connect the signal cables and the power cord to the projector  rst. 2. Combine parts as shown in  gure, and assemble the cable cover. 3. Insert the three knobs on the cable cover into the three hol...

17 Remote control Changing the frequency of remote control signal The accessory remote control has the two choices on signal frequency Mode 1:NORMAL and Mode 2:HIGH. If the remote control does not function properly, attempt to change the signal frequency.In order to set the Mode, please keep pressin...

18 Power on/off 1. Make sure that the power cord is  rmly and correctly connected to the projector and the outlet. Tur ning on the power 2. Make sure that the POWER indicator is steady orange ( 98 ). 3. Con  rm that there is nothing that the lens door hits while opening. Press STANDBY/ ON button o...

19 Power on/off ► Be careful not to pinch your  nger with the lens door, to prevent an injury. ► Do not touch around the lamp cover and the exhaust vents during use or just after use, since it is too hot. ► Remove the power cord for complete separation. The power outlet should be close to the proje...

20 Operating Operating 1. Adjusting the volume Use the VOLUME + / VOLUME - buttons to adjust the volume. A dialog will appear on the screen to aid you in adjusting the volume. If you do not do anything, the dialog will automatically disappear after a few seconds. ● When is selected for current pictu...

21 Operating 1. Press VIDEO button on the remote control. Each time you press the button, the projector switches its input port from the current port as below. Selecting an input signal (continued) ● While ON is selected for AUTO SEARCH item in OPTION menu, the projector will keep checking every por...

22 1. Press ASPECT button on the remote control. Each time you press the button, the projector switches the mode for aspect ratio in turn. Selecting an aspect ratio ● ASPECT button does not work when no proper signal is inputted. ● NORMAL mode keeps the original aspect ratio setting. ● The on-screen...

23 Operating Adjusting the zoom and focus Adjusting the projector's elevator The projector has Front foot for inclinations and Rear foot for horizontals. Spacers on the each elevator foot are installed at the time of shipment, and projector is in a condition to be able to just project. If necessary,...

24 Operating 1. Press AUTO button on the remote control. Pressing this button performs the following. Using the automatic adjustment feature € For a computer signal The vertical position, the horizontal position and the horizontal phase will be automatically adjusted.Make sure that the application w...

25 1. Press the POSITION button on the remote control while no menu is on screen, to display the D-SHIFT ( 42 ) dialog on screen. Adjusting the position 2. Use the ▲ , ▼ , ◄ and ► buttons to adjust the picture position. Press the POSITION button again to  nish this operation. ● This is a function t...

26 Operating 1. Using the magnify feature 2. 3. 4. Press the MAGNIFY ON button on the remote control. The picture will be magni  ed, and the MAGNIFY dialog will appear on the screen. When the MAGNIFY ON button is pressed for the  rst time after the projector is turned on, the picture will be zoome...

27 Operating 1. Press BLANK button on the remote control. The BLANK screen will be displayed instead of the screen of input signal. Please refer to BLANK item in SCREEN menu ( 47 ). To exit from the BLANK screen and return to the input signal screen, press BLANK button again. Temporarily blanking th...

28 Operating 1. To start the MENU, press the MENU button. The MENU you last used (EASY or ADVANCED) will appear. EASY MENU has priority to appear just after powered on. Using the menu function 2. (1) Use the ▲ / ▼ cursor buttons to select an item to operate. If you want to change it to the ADVANCED ...

29 Operating Using the menu function (continued) 3. To close the MENU, press the MENU button again or select EXIT and press the ◄ cursor button or ENTER button. Even if you do not do anything, the dialog will automatically disappear after about 30 seconds. ● If you want to move the menu position, us...

30 EASY MENU EASY MENU From the EASY MENU, items shown in the table below can be performed.Select an item using the ▲ / ▼ cursor buttons. Then perform it according to the following table. Item Description ASPECT Using the ◄ / ► buttons switches the mode for aspect ratio. See the ASPECT item in IMAGE...

32 PICTURE menu PICTURE menu From the PICTURE menu, items shown in the table below can be performed. Select an item using the ▲ / ▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item. Then perform it according to the following table. Item Description BRIGHTNESS Using t...

35 IMAGE menu IMAGE menu From the IMAGE menu, items shown in the table below can be performed.Select an item using the ▲ / ▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item. Then perform it according to the following table. Item Description ASPECT Using the ▲ / ▼ bu...

37 IMAGE menu Item Description H PHASE Using the ◄ / ► buttons adjusts the horizontal phase to eliminate  icker. Right Ù Left • This item can be selected only for a computer signal or a component video signal. This function is unavailable for a signal from the LAN , USB TYPE A , USB TYPE B or HDMI ...

38 INPUT menu INPUT menu From the INPUT menu, items shown in the table below can be performed.Select an item using the ▲ / ▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item. Then perform it according to the following table. Item Description PROGRESSIVE Using the ▲ /...

42 SETUP menu SETUP menu From the SETUP menu, items shown in the table below can be performed.Select an item using the ▲ / ▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item. Then perform it according to the following table. Item Description D-ZOOM Using the ◄ / ► cu...

45 AUDIO menu AUDIO menu From the AUDIO menu, items shown in the table below can be performed. Select an item using the ▲ / ▼ cursor buttons, and press the ► cursor button or the ENTER button to execute the item. Then perform it according to the following table. Item Description VOLUME Using the ◄ /...

46 AUDIO menu Item Description HDMI AUDIO Using the ▲ / ▼ buttons switches the mode for the HDMI TM audio. Check each of the two modes provided and select the suitable one for your HDMI TM audio device. 1 Ù 2 MIC LEVEL Using the ▲ / ▼ buttons switches the input level to match that of the microphone ...

47 SCREEN menu SCREEN menu From the SCREEN menu, items shown in the table below can be performed.Select an item using the ▲ / ▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item. Then perform it according to the following table. Item Description LANGUAGE Using the ▲ /...

48 SCREEN menu Item Description MyScreen This item allows you to capture an image for use as a MyScreen image which can be used as the BLANK screen and START UP screen. Display the image you want to capture before executing the following procedure.1. Selecting this item displays a dialog titled “MyS...

53 OPTION menu OPTION menu From the OPTION menu, items shown in the table below can be performed.Select an item using the ▲ / ▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item, except for the items LAMP TIME and FILTER TIME. Then perform it according to the followin...

59 OPTION menu Item Description SERVICE (continued) KEY LOCK (1) Use the ▲ / ▼ buttons to select CONTROL PANEL or REMOTE CONTROL. (2) Use the ◄ / ► buttons to turn the key lock function on/off. When ON is selected, all buttons on the projector or remote control except the STANDBY/ON button are locke...

61 OPTION menu Item Description SERVICE (continued) COMMUNICATION (continued) COMMUNICATION TYPE Select the communication type for transmission via the CONTROL port. NETWORK BRIDGE Ù OFF NETWORK BRIDGE: Select this type, if it is required to control an external device as a network terminal, via this...

62 OPTION menu Item Description SERVICE (continued) COMMUNICATION (continued) RESPONSE LIMIT TIME Select the time period to wait for receiving response data from other device communicating by the NETWORK BRIDGE and the HALF-DUPLEX through the CONTROL port. OFF Ù 1s Ù 2s Ù 3s OFF: Select this mode if...

63 OPTION menu Item Description SERVICE (continued) INFORMATION Selecting this item displays a dialog titled “INPUT_INFORMATION”. It shows the information about the current input. • The “FRAME LOCK” message on the dialog means the frame lock function is working. • This item can't be selected for no ...

64 NETWORK menu Remember that incorrect network settings on this projector may cause trouble on the network. Be sure to consult with your network administrator before connecting to an existing access point on your network.Select “NETWORK” from the main menu to access the following functions. Select ...

67 NETWORK menu Item Description MY IMAGE Selecting this item displays the MY IMAGE menu. To store images in the projector, the application software PJImg/Projector Image Tool that can be downloaded from our website is required.Use the ▲ / ▼ buttons to select an item which is a still image by the MY...

70 NETWORK menu Item Description INFORMATION Selecting this item displays the NETWORK_INFORMATION dialog for con  rming the network settings. • For the details of PASSCODE, see the section Selecting the network connection method in the User’s manual – Network Guide. • Only the first 16 characters o...

71 SECURITY menu This projector is equipped with security functions.From the SECURITY menu, items shown in the table below can be performed.To use SECURITY menu: User registration is required before using the security functions. Enter to the SECURITY menu 1. Press the ► button. The ENTER PASSWORD bo...

72 SECURITY menu Item Description MyScreen PASSWORD The MyScreen PASSWORD function can be used to prohibit access to the MyScreen function and prevent the currently registered MyScreen image from being overwritten. 1 Turning on the MyScreen PASSWORD 1-1 Use the ▲ / ▼ buttons on the SECURITY menu to ...

77 Presentation tools Presentation tools The PC-LESS Presentation reads image data from storage media inserted into the USB TYPE A port and displays the image on the following modes. The PC-LESS Presentation can be started by selecting the USB TYPE A port as the input source. This feature allows you...

78 Presentation tools Thumbnail mode PC-LESS Presentation (continued) The Thumbnail mode displays the images stored in a USB storage device on the Thumbnail screen. Maximum 20 images are displayed in a screen.If you wish, you can jump into the Full Screen mode or Slideshow mode, after you select som...

79 Presentation tools PC-LESS Presentation (continued) The SETUP menu for the selected image Item Functions SETUP Use the ◄ / ► cursor buttons to switch each setting or use the ► cursor button to execute the functions as follows. RETURN Press the ► cursor button or ENTER to return to the Thumbnail s...

80 Presentation tools You can also control the images by using the menu on the Thumbnail screen. PC-LESS Presentation (continued) Operating by the menu on the Thumbnail screen Item Functions Moves to an upper folder. SORT Allows you to sort  les and folders as following. RETURN Press the ► cursor b...

81 Presentation tools PC-LESS Presentation (continued) • These operations are not accessible while the projector OSD is displayed. • The Thumbnail mode shows 20 pictures in 1 page as maximum.• It is not possible to change the input port by using the INPUT button when the Thumbnail screen, Slideshow,...

82 Presentation tools PC-LESS Presentation (continued) The Full Screen mode shows a full display image. To display in Full Screen mode, select an image in the Thumbnail screen. Then press the ENTER button on the remote control or the INPUT button on the keypad, or click [ENTER] on the Web Remote Con...

83 Presentation tools PC-LESS Presentation (continued) Slideshow mode The following operations can be accessible while the Slideshow is displayed. * These operations are not accessible while the projector OSD is displayed. • It is not possible to change the input port by using the INPUT button when ...

85 Presentation tools PC-LESS Presentation (continued) Playlist The Playlist is a DOS format text  le, which decides the order of displayed still image  les in the Thumbnail or Slideshow. The playlist  le name is “playlist.txt” and it can be edited on a computer. It is created in the folder that ...

86 Presentation tools USB Display The projector can display images transferred from a computer via an USB cable ( 10 ). Select the USB DISPLAY for the USB TYPE B item in the OPTION menu. When you connect your computer to the USB TYPE B port on the projector using a USB cable, the projector will be r...

87 Presentation tools Display : The Floating menu is displayed, and the icon disappears from the Windows noti  cation area. Quit : The application is closed, and the icon disappears from the Windows noti  cation area. The menu shown in the right will be displayed when you right-click the applicati...

88 Presentation tools If you select the Option button on the Floating menu, the Options window is displayed. Optimize Perfor mance The “LiveViewer Lite for USB” captures screenshots in JPEG data and sends them to the projector. The “LiveViewer Lite for USB” has two options that have different compre...

89 Maintenance Maintenance A lamp has  nite product life. Using the lamp for long periods of time could cause the pictures darker or the color tone poor. Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them. Preparation of a new lamp and early...

90 Maintenance Lamp war ning Replacing the lamp (continued) HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE ► The projector uses a high-pressure mercury glass lamp. The lamp can break with a loud bang, or burn out, if jolted or scratched, handled while hot, or worn over time. Note that each lamp has a d...

91 Maintenance The air  lter unit of this projector consists of a  lter cover, two kinds of  lters, and a  lter frame. The new double large  lters system is expected to function longer. However, please check and clean it periodically to keep ventilation needed for normal operation of the projec...

92 Maintenance Cleaning and replacing the air  lter (continued) 9. Turn the projector on and reset the  lter time using the FILTER TIME item in the EASY MENU. ► Before taking care of the air  lter, make sure the power cable is not plugged in, then allow the projector to cool suf  ciently. Taking...

93 Maintenance WARNING ► Be careful of handling a battery, as a battery can cause explosion, cracking or leakage, which could result in a  re, an injury, and environment pollution.• Use only the speci  ed and perfect battery. Do not use a battery with damage, such as a scratch, a dent, rust or lea...

94 Caring for the mirror and lens If the projection mirror or lens is  awed, soiled or fogged, it could cause deterioration of display quality. Please take care of the mirror and lens, being cautious of handling. 1. Turn the projector off and unplug the power cord from the power outlet. And cool th...

95 Maintenance Other care In order to ensure the safe use of your projector, please have it cleaned and inspected by your dealer about once every year. ► Before caring, make sure the power cord is not plugged in, and then allow the projector to cool suf  ciently. The care in a high temperature stat...

96 Troubleshooting Troubleshooting If an abnormal operation should occur, stop using the projector immediately. Otherwise if a problem occurs with the projector, the following checks and measures are recommended before requesting repair. If this does not resolve the problem, please contact your deal...

97 Message Description The internal temperature is rising. Please turn the power off, and allow the projector to cool down at least 20 minutes. After having con  rmed the following items, please turn the power ON again. • Is there blockage of the air passage aperture? • Is the air  lter dirty? • D...

98 Troubleshooting Regarding the indicator lamps When operation of the LAMP , TEMP and POWER indicators differs from usual, check and cope with it according to the following table. POWER indicator LAMP indicator TEMP indicator Description Lighting In Orange Turned off Turned off The projector is in ...

99 Troubleshooting Regarding the indicator lamps (continued) • When the interior portion has become overheated, for safety purposes, the projector is automatically shut down, and the indicator lamps may also be turned off. In such a case, disconnect the power cord, and wait at least 45 minutes. Afte...

100 Troubleshooting Phenomena that may be easy to be mistaken for machine defects About the phenomenon confused with a machine defect, check and cope with it according to the following table. Phenomenon Cases not involving a machine defect Reference page Power does not come on. The electrical power ...

102 Phenomenon Cases not involving a machine defect Reference page Video screen display freezes. The FREEZE function is working. Press FREEZE button to restore the screen to normal. 27 Colors have a faded- out appearance, or Color tone is poor. Color settings are not correctly adjusted. Perform pict...

103 Phenomenon Cases not involving a machine defect Reference page The computer connected to the USB TYPE B port of the projector does not start up. The computer cannot start up in the current hardware FRQ¿JXUDWLRQ Disconnect the USB cable from the computer, then reconnect it after starting up the c...

104 Specifications Speci  cations End User License Agreement for the Projector Software • Software in the projector consists of the plural number of independent software modules and there exist our copyright or/and third party copyrights for each of such software modules.• Be sure to read “End User ...

1 Projector ED-A220N User's Manual (detailed) Network Guide Thank you for purchasing this product. This manual is intended to explain only the network function. For proper use of this product, please refer to this manual and the other manuals for this product. Features This projector has the network...

4 1. Connection to the network 1.1 System requirements 1. Connection to the Network The following equipments are required to connect the projector to your computer through the network. The “LiveViewer” software needs to be installed on all the computers to connect to the projector through a network....

5 1. Connection to the network 1.1 System requirements (continued) • Set your computer’s resolution to XGA or less. Refer to the user manual for your computer or Windows. If it is larger than XGA, the transmission speed will be reduced.• If you use a screen resolution greater than XGA, the projector...

6 1.2 Installing the “LiveViewer” The “LiveViewer” software needs to be installed on all the computers to connect to the projector through a network. You need to log in as an administrator user to install the software. 1) Turn on the computer.2) Shut down all applications.3) Insert the accompanying ...

7 • The C:\Program Files\Projector Tools\LiveViewer folder will be created and the program will be installed into that folder. If you wish to install to a different folder, click the [Browse] and select another folder. NOTE 1. Connection to the network 8) Con  rm the program folder name. If “Projec...

8 1.3 Process to connect the network Before connecting your computer and projector via a network, make sure that the LAN port is selected as the input source on the projector. ( Operating in the User’s Manual – Operating Guide ) Otherwise a connection cannot be established. 1.3.1 Process over view A...

9 1.3.2 Star ting the “LiveViewer” Start the “LiveViewer” in your computer, taking one of the followings. • Double click the “LiveViewer” icon on the Desktop in your computer.• Select “Start” → “All Programs” → “Projector Tools” → “LiveViewer” on Windows menu. Then, proceed to item 1.4 Selecting the...

10 1.4 Selecting the network connection mode • If you select the wireless LAN, the wireless LAN adapters in your computer are shown in the list.• If the wired LAN is selected, the wired LAN adapters in your computer are shown. NOTE After starting the “LiveViewer”, the “Select the Network Connection”...

13 „ Are you sure you want to connect the selected projector? The message is appeared when the wireless adapter you selected is already used for another network connection. • To connect, click the [Yes] . Proceed to item &RQ¿UPLQJWKHFRQQHFWLRQWR your destination . ( 30 ) • Not to connect, click ...

14 1.5 Selecting the network connection method There are some options to connect to the network. • Enter PassCode• Con  gure Manually • Select From List Select From List Before selecting this item, your computer and the projectors need to be connected to the same network.If the connection is alread...

19 If you want to change the Network con  guration to add, click the [Change] . A dialog for changing the Network con  guration as shown to the right will be displayed. Enter IP address and subnet mask , then click the [OK] . Procedure to connect to the projector will start. Proceed to item &R...

21 After entering the Passcode ( 17 ), you are required to enter the network con  guration manually if you use a Subnet mask other than Class A, B or C. ( 15 ) If you use the wired LAN, go to ( 22 ). (3) Confi guring m anually Wireless LAN The projector is required to be connected to an access point...

23 1.6 Manual configuration There are 3 options for the manual con  guration. If you select Con  gure Network Settings Manually, proceed to item &RQ¿JXULQJWKH network settings manually . ( 25 ) • Pro  le ( below ) • History ( 24 ) • Con  gure Network Settings Manually ( 25 ) • To check the se...

25 All setting for the network connection between the projector and computer is input manually. Select the >&RQ¿JXUH1HWZRUN6HWWLQJV Manually] . 1.7 Configuring the network settings m anually The information to be input manually is different, depending on how you want to connect the projector a...

26 Wireless LAN SSID: WirelessAccessPoint (example)Encryption: WEP64bit (example)Encryption key *2 : ********** (example) Mode: INFRASTRUCTURE 2) Click the [Next] . 3) Enter the following information that is set in the projector. *3 IP address : 192.168.1.10 (example)Subnet mask: 255.255.255.0 (exam...

28 1.7 Con  guring the network settings manually (continued) 1. Connection to the network This dialog will be displayed when you need to add a Network con  guration on your computer to connect to the projector. Con  rm with your network administrator if the Network con  guration displayed on the...

29 1.7 Con  guring the network settings manually (continued) 1. Connection to the network If the entered IP address and projector's IP address are the same, a warning dialog shown to the right will be displayed.Click the [OK] , and then enter a different IP address from the projector's one in the d...

30 1.8 Confir m ing the connection to your destination When the network connection is established, the “Connection to Projector successful” screen is displayed. Make sure that the right projector that you want to send your image to is selected, by checking the projector name and IP address shown in t...

31 1.8 Con  rming the connection to your destination (continued) The projector you want to send your images to is in the Slideshow mode in the PC-LESS Presentation. „ A Slideshow is currently running on the projector that you are trying to display to. The projector is not set to the LAN as an input...

37 .$ 3 2.1 Using the “LiveViewer” When you get the connection between your projector and computer, the “LiveViewer” main menu will be shown on the computer screen.On the main menu you can con  gure settings and operate functions to send your images to the projector. 1) Menu Type There are 2 type o...

38 2. Network Presentation 2.1 Using the “LiveViewer” (continued) $ Hold button The image on screen is temporally frozen.The last image before the button is clicked is remained on screen.You can revise the image data on your computer without showing it on the projector’s screen. / Display mode butto...

42 $ Presenter Mode In the Single PC mode, the projector can be occupied by one computer and can block an access from any other computer, if the Presenter mode is selected in the “LiveViewer”.While making your presentation, you don’t need to worry that the image on screen is unexpectedly switched to...

43 2. Network Presentation 2.2 Star ting the Network Presentation This chapter explains the Network Presentation feature with which you can project computer images transmitted through a network. The “LiveViewer” allows you to project images from one or multiple computers by connecting the projector ...

46 3. Web Control 3.1 Logon To use the Web Control function, you need to logon with your user name and password. ( 47 ) Refer to the following for con  guring or controlling the projector via a web browser. 1) Display the logon window as shown on the right. There are two options to display this win...

47 Below are the factory default settings for user name and password. User name Password Administrator <blank> If you logon successfully, the screen below will be displayed. Main menu 3) Click the desired operation or con  guration item on the main menu. 3.1 Logon (Continued) 3. Web Control

48 3.2 Network Infor mation Displays the projector’s current network con  guration settings. Item Description Projector Name Displays the projector name settings. DHCP Displays the DHCP con  guration settings. IP Address Displays the current IP address. Subnet Mask Displays the subnet mask. Defaul...

53 3.6 Aler t Settings Displays and con  gures failure & alert settings. Item Description Cover Error The lamp cover has not been properly  xed. Fan Error The cooling fan is not operating. Lamp Error The lamp does not light, and there is a possibility that interior portion has become heated. T...

54 The Alert Items are shown below. Item Description Alarm Time Con  gures the time to alert. (Only Lamp Time Alarm and Filter Time Alarm .) SNMP Trap Click the [Enable] check box to enable SNMP Trap alerts. Send Mail Click the [Enable] check box to enable e-mail alerts. (Except Cold Start and Auth...

55 3.7 Schedule Settings Displays and con  gures schedule settings. Item Description Daily Con  gures the daily schedule. Sunday Con  gures the Sunday schedule. Monday Con  gures the Monday schedule. Tuesday Con  gures the Tuesday schedule. Wednesday Con  gures the Wednesday schedule. Thursday...

57 • After the projector is moved, check the date and time set for the projector before con  guring the schedules. Strong shock may make the date and time settings ( 58 ) get out of tune. • Events “ My Image ” and “ Messenger ” will not be executed appropriately but result in “schedule execution er...

60 3.9 Security Settings Displays and con  gures passwords and other security settings. Item Description User Account Con  gures the user name and password. User name Con  gures the user name. The length of the text can be up to 32 alphanumeric characters. Password Con  gures the password. The l...

61 3.10 Projector Control Controls the projector. Item Description MAIN POWER Turns the power on/off. INPUT SOURCE Selects the input source. PICTURE MODE Selects the picture mode setting. BLANK ON/OFF Turns Blank on/off. MUTE Turns Mute on/off. FREEZE Turns Freeze on/off. MAGNIFY Controls the magnif...

66 The items shown in the table below can be performed using the Projector Control menu. Click the [Quit Presenter Mode] . Item Description SERVICE Quit Presenter Mode Quit compulsorily from the Presenter mode. 3.10 Projector Control (Continued) 3. Web Control

68 3.12 Projector Status Displays and con  gures the current projector status. Item Description Error Status Displays the current error status Lamp Time Displays the usage time for the current lamp. Filter Time Displays the usage time for the current  lter. Power Status Displays the current power ...

69 3.13 Network Restar t Restarts the projector’s network connection. Item Description Restart Restarts the projector’s network connection in order to activate new con  guration settings. • Restarting requires you to re-log on in order to further control or con  gure the projector via a web browse...

70 4. My Image Function The projector can display still images that are transferred via the network. • It is possible to allocate the image  le up to 4 in the maximum. • Using MY BUTTON that registered MY IMAGE can display transferred image. ( OPTION menu in the User’s Manual – Operating Guide ) • ...

72 1 4 3 2 5. Messenger Function The projector can display the text data transferred via the network on the screen. The text data can be displayed on the screen in two ways that displays the text transferred from the computer on real time, and the other chooses and displays the text data from the on...

73 5. Messenger Function 5. Messenger Function (Continued) Con  gure the following items from a web browser when Messenger function is used. Example : If the IP address of the projector is set to 192.168.1.10: 1) Enter "http://192.168.1.10/" into the address bar of the web browser. 2) Enter...

74 6. Network Bridge Function This projector is equipped with the NETWORK BRIDGE function to perform mutual conversion of a network protocol and a serial interface.Using the NETWORK BRIDGE function, a computer that is connected with this projector by Ethernet communication can control an external de...

75 6. Network Bridge Function 6.2 Communication setup 6.3 Communication por t 1) Using the COMMUNICATION TYPE menu, select the NETWORK BRIDGE for the CONTROL port. 2) Using the SERIAL SETTINGS menu, select the proper baud rate and parity for the CONTROL port, according to the speci  cation of the R...

76 6.4 Transmission method 6.4.1 HALF-DUPLEX The transmission method can be selected from the menus, only when the NETWORK BRIDGE is selected for the COMMUNICATION TYPE.( OPTION menu – SERVICE – COMMUNICATION in the User’s Manual – Operating Guide ) HALF-DUPLEX FULL-DUPLEX This method lets the proje...

80 7.2 Projector Management using SNMP The SNMP (Simple Network Management Protocol) enables to manage the projector information, which is a failure or warning status, from the computer on the network. The SNMP management software will be required on the computer to use this function. • It is recomm...

84 7.4 Command Control via the Network You can con  gure and control the projector via the network using RS-232C commands. Communication Por t The following two ports are assigned for the command control. Command Control Settings ( 50 ) 4) Click the [Enable] check box to open Network Control Port1 ...

85 7.4 Command Control via the Network (Continued) When the authentication setting is enabled, the following settings are required. ( 60 ) 7) Click the [Security Settings] on the main menu. 8) Click the [Network Control] and enter the desired authentication password. * See NOTE. 9) Click the [Apply]...

86 Command For mat Command formats differ among the different communication ports. ● TCP #23You can use the RS-232C commands without any changes. The reply data format is the same as the RS-232C commands. ( “RS-232C Communication” in the User’s Manual – Operating Guide (Technical) ) However, the fol...

87 Reply Data for mat The connection ID (the data is same as the connection ID data on the sending data format) is attached to the RS-232C commands reply data. <ACK reply> Reply Connection ID 0x06 1 byte <NAK reply> Reply Connection ID 0x15 1 byte <Error reply> Reply Error code Con...

88 Automatic Connection Break The TCP connection will be automatically disconnected after there is no communication for 30 seconds after being established. The projector does not accept commands without authentication success when authentication is enabled. The projector uses a challenge response ty...

1 NOTE • Be sure to check jack type, signal level, timing and resolution before connecting this projector to a PC.• Some PCs may have multiple display screen modes. Use of some of these modes will not be possible with this projector.• Depending on the input signal, full-size display may not be possi...

2 Initial set signals Initial set signals The following signals are used for the initial settings. The signal timing of some computer models may be different. In such case, adjust the items V POSITION and H POSITION in the IMAGE menu. Back porch (B) Front porch (D) Back porch (b) Front porch (d) Act...

3 Connection to the por ts Connection to the ports NOTICE ► Use the cables with straight plugs, not L-shaped ones, as the input ports of the projector are recessed. ► Only the signal that is input from the COMPUTER IN1 or IN2 can be output from the MONITOR OUT port. COMPUTER IN1 COMPUTER IN2 HDMI US...

7 Connection to the por ts (continued) To input component video signal to COMPUTER IN ports ex. To input component video signal to the COMPUTER IN1 or IN2 port of the projector, use a RCA to D-sub cable or adapter. For about the pin description of the required cable or adapter, refer to the descript...

8 RS-232C Communication RS-232C Communication When the projector connects to the computer by RS-232C communication, the projector can be controlled with RS-232C commands from the computer. For details of RS-232C commands, refer to RS-232C Communication / Network command table ( 17 ). Connection 1. T...

9 RS-232C Communication (continued) Communicaion settings 1. Protocol 19200bps,8N1 2. Command for mat ("h" shows hexadecimal) Byte Number 0 1 2 3 4 5 6 7 8 9 10 11 12 Command Action Header Data Header code Packet Data size CRC  ag Action Type Setting code L H L H L H L H L H L H <SET>...

12 Communicaion Por t The following two ports are assigned for the command control. TCP #23TCP #9715 Con  gure the following items form a web browser when command control is used. Port Settings Network Control Port1 (Port: 23) Port open Click the [Enable] check box to open [Network Control Port1 (P...

13 Command Control via the Network (continued) Command control settings [TCP #23] 1. Command for mat Same as RS-232C communication, refer to RS-232C Communicaton command format. 2. Response code / Error code ("h" shows hexadecimal) Four of the response / error code used for TCP#23 are the sa...

15 This projector is equipped with NETWORK BRIDGE function. When the projector connects to the computer by LAN communicaton, an external device that is connected with this projector by RS-232C communication can be controlled from the computer as a network terminal. For details, see the 6. Network Br...

16 Communication settings For communication setting, use the OPTION - SERVICE - COMMUNICATION menu. (  OPTION menu - SERVICE - COMMUNICATION in the User's Manual - Operating Guide ) Item Condition BAUD RATE 4800bps / 9600bps / 19200bps / 38400bps Data length 8 bit (  xed) PARITY NONE/ODD/EVEN Star...

31 PJLink command PJLink command POWR Power Contorol 0 = Standby 1 = Power On POWR ? Power Status inquiry 0 = Standby 1 = Power On 2 = Cool Down INPT Input Source selection 11 = COMPUTER IN 1 12 = COMPUTER IN 2 22 = S-VIDEO 23 = VIDEO 31 = HDMI 41 = USB TYPE A 51 = LAN 52 = USB TYPE B INPT ? Input S...

2 First of all Entries and graphical symbols explanation The following entries and graphical symbols are used for the manuals and the product as follows, for safety purpose. Please know their meanings beforehand, and heed them. Impor tant safety instruction The followings are important instructions ...

3 ENGLISH Regulator y notices About Electro-Magnetic Interference This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. This product may cause interference if used in residential areas. Such us...

4 Contents of package Your projector should come with the items shown below. Check that all the items are included. Require of your dealer immediately if any items are missing. (1) Remote control with the two AA batteries (2) Power cord (3) Computer cable(4) Parts of cable cover (5) User’s manuals (...

5 ENGLISH WARNING ► Install the projector in a stable horizontal position. ► Place the projector in a cool place, and ensure that there is suf  cient ventilation. Do not place the projector where the air from an air conditioner or similar unit will blow on it directly. ► Do not place the projector ...

6 Access point COMPUTER IN1 COMPUTER IN2 HDMI USB TYPE B S-VIDEO VIDEO AUDIO OUT AUDIO IN3 AUDIO IN1 AUDIO IN2 MIC MONITOR OUT CONTROL USBTYPE A DC5V 0.5A R L COMPONENT Cb/Pb Y Cr/Pr AUDIO OUT HDMI R L R L VIDEO S-VIDEO AUDIO OUT AUDIO OUT AUDIO OUT USB (A) DISPLA Y RS-232C LAN VCR/DVD/Blu-ray Disc ...

8 Connecting power supply 1. Put the connector of the power cord into the AC IN (AC inlet) of the projector. 2. Firmly plug the power cord’s plug into the outlet. In a couple of seconds after the power supply connection, the POWER indicator will light up in steady orange. Please remember that when t...

9 ENGLISH Using the cable cover Utilize the cable cover as the guard and blind for the connecting parts. 1. Connect the signal cables and the power cord to the projector  rst. 2. Combine parts as shown in  gure, and assemble the cable cover. 3. Insert the three knobs on the cable cover into the th...

10 Preparing for the remote control Please insert the batteries into the remote control before using it. If the remote control starts to malfunction, try to replace the batteries. If you will not use the remote control for long period, remove the batteries from the remote control and store them in a...

12 Adjusting the projector's elevator The projector has Front foot for inclinations and Rear foot for horizontals. Spacers on the each elevator foot are installed at the time of shipment, and projector is in a condition to be able to just project. If necessary, detach the spacer, and the elevator fe...

14 Tur ning off the power 1. Press the STANDBY/ON button on the projector or the remote control. The message “Power off?” will appear on the screen for about 5 seconds. 2. Con  rm that there is nothing that the lens door hits while closing. Press the STANDBY/ON button again while the message appear...

15 ENGLISH Replacing the lamp A lamp has  nite product life. Using the lamp for long periods of time could cause the pictures darker or the color tone poor. Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them.Preparation of a new lamp and ear...

16 HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE WARNING ► The projector uses a high-pressure mercury glass lamp. The lamp can break with a loud bang, or burn out, if jolted or scratched, handled while hot, or worn over time. Note that each lamp has a different lifetime, and some may burst or burn out...

18 1. Turn the projector off, and unplug the power cord. Allow the projector to cool suf  ciently. 2. After making sure that the projector has cooled adequately, slowly turn over the projector, so that the bottom is facing. 3. Turn the battery cover fully in the direction indicated “OPEN” using a c...

19 ENGLISH Caring for the mirror and lens If the projection mirror or lens is  awed, soiled or fogged, it could cause deterioration of display quality. Please take care of the mirror and lens, being cautious of handling. 1. Turn the projector off and unplug the power cord from the power outlet. And...

20 Using the CD manual The other manuals for this product are written into the included CD-ROM titled “User’s Manual (detailed)”. Before using the CD-ROM, please read the following to ensure the proper use. System requirements The system for using the CD-ROM requires the following. Windows ® : OS:Mi...

22 Troubleshooting - Warranty and after-ser vice If an abnormal operation (such as smoke, strange odor or excessive sound) should occur, stop using the projector immediately. Otherwise if a problem occurs with the projector,  rst refer to “Troubleshooting” of “Operating Guide” and “Network Guide”, ...