Hitachi CP-WUX645N - Manuals

Page 2 - Initial set signals; and H POSITION in the IMAGE menu.; Data

2 Initial set signals Initial set signals The following signals are used for the initial settings. The signal timing of some computer models may be different. In such case, adjust the items V POSITION and H POSITION in the IMAGE menu. Back porch (B) Front porch (D) Back porch (b) Front porch (d) Dis...

Page 3 - HDMI; RGB OUT; At RGB signal

3 D HDMI • Type :Digital audio/video connector • Audio signal : Linear PCM (Sampling rate; 32/44.1/48 kHz) Connection to the ports A RGB 1, B RGB OUT D-sub 15pin mini shrink jack • Video signal: RGB separate, Analog, 0.7Vp-p, 75Ω terminated (positive) • H/V. sync. signal: TTL level (positive/negativ...

Page 4 - VIDEO; Mini DIN 4pin jack; COMPONENT VIDEO; Port

4 LAN AC IN I O VIDEO CONTROL AUDIO IN1 AUDIO IN2 AUDIO OUT RGB OUT RGB1 RGB2 HDMI R L R L AUDIO IN3 AUDIO IN4 C B /P B Y C R /P R B/C B /P B R/C R /P R G/Y H V USB REMOTE CONTROL S-VIDEO Connection to the ports (continued) 4 3 2 1 I VIDEO RCA jack• System: NTSC, PAL, SECAM, PAL-M, PAL-N, NTSC4.43, ...

Page 5 - Pin

5 LAN AC IN I O VIDEO CONTROL AUDIO IN1 AUDIO IN2 AUDIO OUT RGB OUT RGB1 RGB2 HDMI R L R L AUDIO IN3 AUDIO IN4 C B /P B Y C R /P R B/C B /P B R/C R /P R G/Y H V USB REMOTE CONTROL S-VIDEO J AUDIO IN 1, K AUDIO IN 2 Ø3.5 stereo mini jack• 500 mVrms 47kΩ terminator AUDIO IN 3 L R, M L, AUDIO IN 4 N R,...

Page 6 - LAN; USB; USB B type jack

6 LAN AC IN I O VIDEO CONTROL AUDIO IN1 AUDIO IN2 AUDIO OUT RGB OUT RGB1 RGB2 HDMI R L R L AUDIO IN3 AUDIO IN4 C B /P B Y C R /P R B/C B /P B R/C R /P R G/Y H V USB REMOTE CONTROL S-VIDEO Connection to the ports (continued) T LAN RJ-45 jack Pin Signal Pin Signal Pin Signal 1 TX+ 4 - 7 - 2 TX- 5 - 8 ...

Page 7 - RS-232C Communication; Connecting the cable

7 RS-232C Communication RS-232C Communication 6 7 8 9 1 2 3 4 5 6 7 8 9 1 2 3 4 5 CONTROL port RS-232C cable (Cross) RS-232C port of the projector of the computer - (1) (1) CD RD (2) (2) RD TD (3) (3) TD - (4) (4) DTR GND (5) (5) GND - (6) (6) DSR RTS (7) (7) RTS CTS (8) (8) DTS - (9) (9) RI Connect...

Page 8 - NOTE; • Operation cannot be guaranteed when the projector receives an

8 RS-232C Communication (continued) Requesting projector status (Get command) (1) Send the request code Header + Command data (‘02H’+‘00H’+ type (2 bytes)+‘00H’ +‘00H’) from the computer to the projector. (2) The projector returns the response code ‘1DH’+ data (2 bytes) to the computer. Changing the...

Page 9 - Communication Port; The following two ports are assigned for the command control.; Command Control Settings; Port Settings; and

9 Command Control via the Network Communication Port The following two ports are assigned for the command control. TCP #23 TCP #9715 Command Control Settings Configure the following items form a web browser when command control is used. When the authentication setting is enabled, the following setti...

Page 10 - Command Format; Requesting projector status (Get command)

10 Command Control via the Network (continued) Command Format [TCP #23] 1. Protocol Consist of header (7 bytes) + command data (6 bytes) 2. Header BE + EF + 03 + 06 + 00 + CRC_low + CRC_high CRC_low: Lower byte of CRC flag for command data CRC_high: Upper byte of CRC flag for command data 3. Command...

Page 11 - Decreasing the projector setting value (Decrement command); ‘xxxxH’; When authentication error occurred.; is sent

11 Command Control via the Network (continued) Decreasing the projector setting value (Decrement command) (1) The PC sends the following decrement code to the projector. Header + Command data (‘05H’ + ‘00H’ + type (2 bytes) + ‘00H’ + ‘00H’) (2) The projector decreases the setting value on the above ...

Page 12 - ‘xxH’; Automatic Connection Break; • As for the transmission of the second or subsequent commands, the

12 7. Reply Data The connection ID (the data is same as the connection ID data on the sending data format) is attached to the Network control commands reply data. ACK reply: ‘06H’ + ‘xxH’ NAK reply: ‘15H’ + ‘xxH’ Error reply: ‘1CH’ + ‘xxxxH’ + ‘xxH’ Data reply: ‘1DH’ + ‘xxxxH’ + ‘xxH’ Projector busy...

Page 13 - RS-232C Communication / Network command table

13 RS-232C Communication / Network command table Names Operation Type Header Command Data CRC Action Type Setting Code Power Set TURN OFF BE EF 03 06 00 2A D3 01 00 00 60 00 00 TURN ON BE EF 03 06 00 BA D2 01 00 00 60 01 00 Get BE EF 03 06 00 19 D3 02 00 00 60 00 00 (Example Return) 00 00 01 00 02 0...