Page 2 - Example of computer signal; NOTE; • Be sure to check jack type, signal level, timing and resolution
2 Example of computer signal Resolution (H x V) H. frequency (kHz) V. frequency (Hz) Rating Signal mode *1 1280 x 1024 91.1 85.0 VESA SXGA (85Hz) *2 1400 x 1050 65.2 60.0 VESA SXGA+ (60Hz) *3 1680 x 1050 65.3 60.0 VESA WSXGA+ (60Hz) *1 1600 x 1200 75.0 60.0 VESA UXGA (60Hz) *4 1920 x 1200 74.0 60.0 ...
Page 3 - Data; Reduced Blanking; and H POSITION in the IMAGE menu.; Initial set signals
3 Initial set signals Back porch (B) Front porch (D) Back porch (b) Front porch (d) Active video (C) Data Data H. Sync. V. Sync. Sync (A) Sync (a) Active video (c) Resolution (H x V) Horizontal signal timing (μs) Vertical signal timing (lines) Signal mode (A) (B) (C) (D) (a) (b) (c) (d) 720 x 400 2....
Page 4 - D-sub 15pin mini shrink jack; Connection to the ports; Connection to the ports; NOTICE; ►Use the cables with straight plugs, not L-shaped ones, as the; COMPUTER IN1; or; MONITOR OUT
4 A COMPUTER IN1, B MONITOR OUT D-sub 15pin mini shrink jack <Computer signal> • Video signal: RGB separate, Analog, 0.7Vp-p, 75Ω terminated (positive) • H/V. sync. signal: TTL level (positive/negative) • Composite sync. signal: TTL level<Component video signal> • Video signal: Y with co...
Page 5 - COMPUTER IN2; HDMI; connector; FF
5 Connection to the ports (continued) COMPUTER IN2 C G/Y, D B/Cb/Pb, E R/Cr/Pr, F H, G V BNC jack x5 <Computer signal> • Video signal: RGB separate, Analog, 0.7Vp-p, 75Ω terminated (positive) • H/V. sync. signal: TTL level (positive/negative) • Composite sync. signal: TTL level<Component vi...
Page 6 - VIDEO
6 M S-VIDEO Mini DIN 4pin jack• S-video signal, Analog: -Brightness signal with composite sync, 1.0±0.1Vp-p, 75Ω terminated -Color signal, 0.286Vp-p (NTSC, burst), 75Ω terminated 0.300Vp-p (PAL/SECAM, burst) 75Ω terminated • System: NTSC, PAL, SECAM, PAL-M, PAL-N, NTSC4.43, PAL(60Hz) Pin Signal 1 C ...
Page 8 - Network Guide; USB TYPE A; Y Z
8 REMOTE CONTROL Y IN, Z OUT Ø3.5 stereo mini jack Connection to the ports (continued) X USB TYPE B USB B type jack Pin Signal 1 +5V 2 - Data 3 + Data 4 Ground V LAN RJ-45 jack* About the details of network communication, please refer to the Network Guide . Pin Signal Pin Signal Pin Signal 1 TX+ 4 -...
Page 9 - To input SCART RGB signal; Video; Audio; To input SCART RGB signal to the projector, use a SCART to RCA cable.
9 To input SCART RGB signal; ex. Video G B R Audio L Audio R Connection to the ports (continued) To input SCART RGB signal to the projector, use a SCART to RCA cable. Connect the plugs refer to above ex. For more reference, please consult your dealer. SCART connector (jack) SCART cable (plug) RCA pl...
Page 10 - RS-232C Communication; Connection; Turn off the projector and the computer.; CONTROL; CONTROL; port
10 ① ② ⑥ ⑦ ⑧ ⑨ ⑤ ④ ③ ① ② ⑥ ⑦ ⑧ ⑨ ⑤ ④ ③ CD (1) (1) - RD(2) (2) RD TD (3) (3) TD DTR (4) (4) - GND (5) (5) GND DSR (6) (6) - RTS (7) (7) RTS DTS (8) (8) CTS RI (9) (9) - RS-232C Communication RS-232C Communication When the projector connects to the computer by RS-232C communication, the projector can ...
Page 11 - Communicaion settings; table
11 RS-232C Communication (continued) Communicaion settings 1. Protocol 19200bps, 8N1 2. Command format ("h" shows hexadecimal) Byte Number 0 1 2 3 4 5 6 7 8 9 10 11 12 Command Action Header Data Header code Packet Data size CRC flag Action Type Setting code L H L H L H L H L H L H <SET>...
Page 13 - LAN; Command Control via the Network
13 When the projector connects network, the projector can be controlled with RS- 232C commands from the computer with web browser. For details of RS-232C commands, refer to RS-232C Communication / Network command table ( & 19 ). Command Control via the Network LAN USB wireless adapter LAN cable ...
Page 14 - Communicaion Port; The following two ports are assigned for the command control.; Port Settings; Security Settings
14 Communicaion Port The following two ports are assigned for the command control. TCP #23 TCP #9715 Configure the following items form a web browser when command control is used. Port Settings Network Control Port1 (Port: 23) Port open Click the [Enable] check box to open [Network Control Port1 (Po...
Page 15 - Command Control via the Network (continued); Command control settings; Refer to RS-232C communication; Header; Refer to RS-232C Communication command format; • Operation cannot be guaranteed when the projector receives an
15 Command Control via the Network (continued) Command control settings [TCP #23] 1. Command format Same as RS-232C communication, refer to RS-232C Communicaton command format. 2. Response code / Error code ("h" shows hexadecimal) Four of the response / error code used for TCP#23 are the sam...
Page 16 - used. The connection ID is same as the sending command format.; Automatic Connection Break
16 NOTE • As for the transmission of the second or subsequent commands, the authentication data can be omitted when the same connection. Command Control via the Network (continued) 2. Response code / Error code ("h" shows hexadecimal) The connection ID is attached for the TCP#23's response /...
Page 17 - Connect the projector's; port and the RS-232C port of the devices; Network Bridge Communication
17 This projector is equipped with NETWORK BRIDGE function. When the projector connects to the computer by wired or wireles LAN communicaton, an external device that is connected with this projector by RS- 232C communication can be controlled from the computer as a network terminal. For details, see...
Page 18 - Communication settings; Data length; • For connecting the projector to your devices, please read the; Transmission method; in the
18 Communication settings For communication setting, use the COMMUNICATION menu in the OPTION - SERVICE menu Item Condition BAUD RATE 4800bps / 9600bps / 19200bps / 38400bps Data length 8 bit (fixed) PARITY NONE/ODD/EVEN Start bit 1 bit (fixed) Stop bit 1 bit (fixed) Transmission method HALF-DUPLEX/...
Page 19 - RS-232C Communication / Network command table
19 RS-232C Communication / Network command table RS-232C Communication / Network command table (continued on next page) Names Operation Type Header CRC Command Data Action Type Setting code Power Set Turn off BE EF 03 06 00 2A D3 01 00 00 60 00 00 Turn on BE EF 03 06 00 BA D2 01 00 00 60 01 00 Get B...
Page 37 - PJLink command; POWR
37 PJLink command PJLink command POWR Power Contorol 0 = Standby 1 = Power On POWR ? Power Status inquiry 0 = Standby 1 = Power On 2 = Cool Down INPT Input Source selection 11 = COMPUTER IN 1 12 = COMPUTER IN 2 21 = COMPONENT 22 = S-VIDEO 23 = VIDEO 31 = HDMI 1 33 = HDMI 2 41 = USB TYPE A 51 = LAN 5...