Hitachi CP-S860E - Manuals

6 ■ Do not sit or place heavy objects onthis projector. • Do not sit on this projector. This could result in overturning,leading to damage or personal injury.Use special caution in householdswhere children are present. • D o n o t p l a c e h e av y o b j e c t s o n t h i sprojector. Placing heavy ...

7 ■ Avoid excessively hot locations. Do not place this projector in directsunlight or near a hot object such as astove, etc., because the heat couldhave adverse influence on the cabinetand other parts. ■ Sound volume. S e t t h e v o l u m e a t a s u i t a b l e l e v e l t o a v o i dbothering oth...

8 Checking the package Contents Make sure all of the following items are included in the package. If anything is missing, please contact yourdealer. • Use the remote control in front of the remote control photoreceptor at a distance of about 5 m or less and an angle of 30 degrees to the left or righ...

9 RGB IN 1 2 CONTROL RGB OUT S-VIDEO IN VIDEO IN AUDIO IN L MONO R USB AUDIO OUT AUDIO IN 1 2 Names and functions of each part (continued) Main power switch Used to turn the power on and off. : OFF : ON VIDEO IN jack S-VIDEO IN jack Mini DIN 4-pin connector VIDEO IN jack RCA jack AUDIO L/R IN jack R...

10 Names and functions of each part (continued) Remote control transmitter FOCUS button Used to adjust the focus of the image on thescreen. (Refer to page 13.) ZOOM button Used to adjust the size of the image. (Refer topage 13.) FREEZE button Used to turn the freeze (still) image display onand off. ...

11 Names and functions of each part (continued) Loading the batteries Loading AA batteries into the remote control. The laser pointer of the remote control is used in place of a finger or rod.Never look directly into the laser beam outlet or point the laser beam atother people.The laser beam can cau...

12 Installation Typical LCD Projector and Screen Installation Using the adjusters a. Distance from the LCD projector to the screenb. Distance from the lens center to the bottom of the screen (a,b : +/-10%). The projection distances shown in the diagram tothe left are for full size (800 x 600 dots). ...

13 Basic operations To project 1 Turn on the main power switch of the projector [ I: ON]. • The ON indicator will light orange. 2 Press the STANDBY / ON button. • The ON indicator will blink green and then light green.• The green blinking indicates warmup.• After the power is turned on, the lamp wil...

14 VIDEO STANDBY/ON RGB POSITION LASER MENU RESET MAGNIFY FREEZE OFF VOLUME P in P MUTE AUTO BLANK TIMER Turning off the power Plug & Play Basic operations (continued) 1 Press the STANDBY/ON button for approximately 1 sec. • The ON indicator will blink orange, then the lamp will turn off. Approx...

15 VIDEO STANDBY/ON RGB POSITION LASER MENU RESET MAGNIFY FREEZE OFF VOLUME P in P MUTE AUTO BLANK TIMER Freeze function Basic operations (continued) 1 Press the FREEZE button. • The image being displayed will freeze.• The [ ] mark will be displayed for approximately 3 sec. when the FREEZE function ...

16 1 Press the MAGNIFY + button. • The center part of the image will be displayed magnified approximately two times. 2 Press the MAGNIFY + button. • When this button is pressed, the image will be displayed even larger. 3 Press the MAGNIFY – button. • When this button is pressed, the image will be di...

VIDEO STANDBY/ON RGB POSITION LASER MENU RESET MAGNIFY FREEZE OFF VOLUME P in P MUTE AUTO BLANK TIMER FOCUS ZOOM MENU 17 Returning to the initial settings Adjustments and functions 1 Press the MENU ( ) buttons of the projector or theMENU button of the remote control. • The Menu screen will appear. (...

18 Adjustments and functions (continued) RGB signal input Video signal input VOLUME BRIGHT CONTRAST V POSITH POSIT H PHASE H SIZE COLOR BAL RCOLOR BAL B 100100 800 S E T U P I N P U T O P T . I M A G E VOLUME BRIGHT CONTRAST SHARPNESS COLOR TINT COLOR BAL RCOLOR BAL B S E T U P I N P U T O P T . I M...

19 Adjustments and functions (continued) INPUT The INPUT menu is used to select RGB signal sync signal frequency of the monitor and the VIDEO signal. RGBVIDEO fH:38kHz fV:60Hz S E T U P I N P U T O P T . I M A G E RGBVIDEO AUTONTSCPALSECAMNTSC4.43M-PALN-PAL S E T U P I N P U T O P T . I M A G E Adju...

20 Adjustments and functions (continued) Adjustment item KEYSTONE MIRROR BLANK START UP P in P Adjustment description Reduces keystone Reduces keystone distortion at the bottom distortion at the top Sets vertical or horizontal inversion of the projected image.H: horizontal inversion onlyV: vertical ...

21 Adjustments and functions (continued) OPT Communication functions, etc., can be set from the OPT menu. Adjustment item COM. SPEED COM. BITS TIMER LANGUAGE AUTO OFF SYNC ON G Adjustment description Sets the communication speed (5 steps). Sets the bit configuration for the communication data.7N1......

22 Connection to the video signal terminals Connection to the RGB signal terminal 1. Input signals 2. Signal input jacks 1. Input signals 2. Signal input jacks S-VIDEO input (mini DIN 4-pin) Color signal Ground Ground Brightness signal The priority sequence of the video input jacks is as follows.(1)...

23 Connection to the RGB signal terminal (continued) • Some computers may have multiple display screen modes. Use of some of these modes will not be possible with this projector. • Be sure to check jack type, signal level, timing and resolution before connecting this projector to a computer. • Depen...

24 Connection to the RGB signal terminal (continued) 4. Initial set signals The following signals are used for the initial settings.The signal timing of some computer models may be different. In such case, refer to pages 17 and 18 and adjustthe V.POSIT and H.POSIT of the menu. DATA HSYNC a c b d DAT...

25 Connecting the USB 1. Connect the projector and computer with a suitable commercially available cable.2. Press the INPUT button of the projector or the RGB 1/2 button of the remote control and select the input where the computer is to be connected. 3. Start the mouse function.4. Refer to page 10,...

26 Connection to the control signal terminal Use the mouse cable provided or a PS/2 mouse cable (for IBM and compatibles).Cables for ADB mouse (Apple), bus mouse (NEC) and serial mouse are available as options. 123456789 10 11 12 131415 CLK DATA RTS SEL0 GND 123456 DATA +5V GND CLK 6 3 4 2 1 +5V 5 c...

27 Connection to the control signal terminal (continued) CONTROL signal jack ADB (Mac) mouse 123456789 10 11 12 131415 DATA RTS GND 1234 ADB +5V GND 3 4 2 1 +5V (POWER ON) Projector Computer M o u s e j a c kMini DIN 4-pin Mouse cable (ADB) (option) Serial mouse 123456789 1011 12 131415 GND TD 12345...

29 Connection to the control signal terminal (continued) The command code configuration consists of a 2-byte command and the following data. • The first byte of a command indicates the command type with 3 bits on the MSB side and the data length with 4 bits on the LSB side. Projector - computer Comp...

31 RGB IN 1 2 CONTROL RGB OUT S-VIDEO IN VIDEO IN AUDIO IN L MONO R USB AUDIO OUT AUDIO IN 1 2 Example of system setup Cleaning the Air filter Turn power off to all devices before connecting. Refer to the instruction manual of each device before connecting. Caution AC input Video tape recorder with ...

32 Cleaning the Air filter (continued) 3 Cleaning the air filter with a vacuum cleaner 4 Installing the air filter When the air filter becomes clogged with dust, etc., the projector power may turn off toprevent the internal heat level rising.Do not operate the projector with the air filter removed. ...

33 Message table (continued) Indicators The ON indicator, LAMP indicator and TEMP indicator light or blink in the following cases. ON indicator Lights orange Flashes green Lights green Flashes orange Lights red Lights red Lights red Flashes red LAMP indicator Turns off Turns off Turns off Turns off ...

34 Specifications Dimensional Diagram · These specifications are subject to change without notice.· This liquid crystal projector is designed for use in Japan and cannot be used in any other country. Unit: mm Product name Liquid crystal projector Model CP-S860W/E Display method Three liquid crystal ...

35 About the warranty and after-service About the warranty A warranty is provided for this product. Fill in the necessary items and store in a safe place. About after-service When a problem occurs, please check first using the Troubleshooting Chart provided in this instruction manual.If the problem ...