Hitachi CP-S845W - Manuals

When you are not going to use for a long time. When you are not going use this unitfor a long time because you are goingon a trip, etc., be sure to pull out thepower plug from the power outlet forsafety. And also apply cover to thelens so that the lens is not damaged. Clean inside the unit at least ...

7 ENGLISH Caution Do not place this unit where it gets hot. Be careful since if you place the unitoutdoors, in a place exposed to directsunlight or near a heating device,the cabinet and parts could beaffected. Cleaning the lens. To clean the lens, use a generally-available lenscleaning tissue (used ...

8 Main unit Lens Speaker Speaker Remote controlsensor • Use the remote control transmitter within the rangeof about 16 feet from the remote control sensor andwithin 30 ° to both the left and right. Cooling fan (exhaust) Contents of shipping box Handle STANDBY / ON button Power ON/OFF button.OFF sets...

9 ENGLISH Names and functions of each part (continued) RGB input terminal D-sub 15pin shrink terminal (1/2) VIDEO input terminal (on video-equipped models only) S-VIDEO input terminal Mini DIN 4pin connector VIDEO input terminal RCA Jack AUDIO L/R input terminal RCA Jack AC IN socket Connect the pro...

10 MUTE button Silences the sound. (Cancels the mute whenthe unit is set in mute mode.) VOLUME button Adjusts volume. The sound is loud or lowwhile pressing the "+" or "-" button. LASER button Laser pointer ON button. Use as a stick (forindication). (See page 11) MOUSE LEFT button M ...

11 ENGLISH Slide the battery compartment coverin the direction of the arrow whilepressing slightly down on it. Caution Cautions on use of batteries • Do not use batteries not specified for this unit.Also do not use old and new batteries together.It may cause a fire, injury due to burst ofbattery or ...

12 Please basically use liquid crystal projector at the horizontalposition. If you use liquid crystal projector by the lens up position, the lensdown position and the side up position, this may cause the heatinside to build up and become the cause of damage.Be especially careful not to install it wi...

13 ENGLISH 7 Press the INPUT button or the INPUT SELECT (VIDEO orRGB) button to select the source of the signal to be projectedon the screen. • The selected signal input is displayed at the bottom right of the screen for 3 seconds. Power on all connected equipment. The method of connecting various e...

14 Basic operations (continued) • To reduce temperature inside the projector, fan will rotate for about 1 minute after the lampis turned off. • Do not turn off the MAIN POWER switch during the lamp on because the lamp is damaged. Press the STANDBY/ON button, for 1 second. • The ON indicator blinks o...

15 ENGLISH Basic operations (continued) MAGNIFYING FUNCTION It is possible to display a partially magnified picture. This function can be used in combination with aFREEZE function. [TO CHANGE MAGNIFICATION] 3 Press the MAGNIFY + button. • By doing so, the center of the picture can be magnified as on...

16 Press the MENU ( ) buttons or the MENU ON / OFF button. • On-screen menus are displayed on the screen. 1 Select the menu to be adjusted using the MENU ( ) buttons or DISK PAD. • Menu displayed in green is selected. 2 Select the item to be adjusted using the MENU ( ) buttons or DISK PAD. • Item di...

17 ENGLISH RGB signal input VIDEO signal input The menu SET UP serves for the change of parameters influencing the picture and forthe move picture position. Adjustments and functions (continued) SET UP S E T U P I N P U T I M A G E O P T . VOLUMEBRIGHTCONTRASTV POSITH POSITH PHASEH SIZECOLOR BAL 121...

18 Adjustments and functions (continued) The menu INPUT serves for the selection of input source. INPUT S E T U P I N P U T I M A G E O P T . RGB1RGB2VIDEO S E T U P I N P U T I M A G E O P T . RGB1RGB2V I DEO S Y S T E M AUTONTSCPALSECAMNTSC4.43M-PALN-PAL Adjustment Item Details of adjustment RGB 1...

19 ENGLISH The menu OPT. allows you to control communication function etc. Adjustments and functions (continued) S E T U P I N P U T I M A G E O P T . COM. SPEEDCOM. BITSTIMERLANGUAGEAUTO OFFSTART UP S E T U P I N P U T I M A G E O P T . 7N1 8N1 COM. BITS S E T U P I N P U T I M A G E O P T . 120024...

20 1. Input / output signal Connection to the RGB signal terminal 2. Signal input / output terminal 5 1 10 6 15 11 D-sub 15pin shrink terminal(Female) 1. Input signal Connection to the video signal terminals 2. Signal input terminal Ground Luminance signal S VIDEO input (Mini DIN4 pin) Ground Chromi...

21 ENGLISH 3. Example of computer signal Note 1: Signal mode Note 2: MAC adapter is necessary to the resolution mode. Projector is compatible with 13 inch mode and 16 inch mode.MAC13"mode=switch 1 and switch 2 are ON.MAC16"mode=switch 2 and switch 4 are ON. Note 3:Display mode Connection to ...

22 4. Initial set signals The following signals are initially set. The settings may be different depending on the computer type. In this case, adjust the settings referring to pages 16, 17. Connection to the RGB signal terminal(continued) Back porch(b) Back porch(b) DATA HSYNC DATA VSYNC Sync.(a) Fr...

23 ENGLISH 1. Control signal terminal Connection to the control signal terminal 2. Mouse emulation 5 1 10 6 15 11 D-sub 15pin shrink terminal (Male) Caution Turn off the power of both the projector and computer before connecting. Connect the computer to the control terminal of the projector using an...

24 Connection to the control signal terminal (continued) PS/2 mouse ADB (Mac) mouse 2 1 4 3 6 5 2 1 4 3 6 5 8 7 10 9 12 11 14 13 15 CLK DATA SEL0 RTS GND +5V DATA GND+5VCLK 2 1 4 3 6 5 2 1 4 3 8 7 10 9 12 11 14 13 15 RTS GND +5V ADB GND +5V (POWER ON) DATA 2 1 4 3 6 5 2 1 4 3 Projector Computer Mini...

25 ENGLISH Connection to the control signal terminal (continued) 3. Communication (1) Connect the projector and computer using RS 232C cable. (2) Turn off the computer and after computer is setting up, turn on the projector. (3) Select the data speed (COM.SPEED) and the data format (COM.BITS) of the...

26 Connection to the control signal terminal (continued) Command data Caution If computer sends the undefined command code or data code, Projector can not guarantee operation. Command is consisted of 2 command bytes and following data bytes.1-st byte indicates the kinds of commands and the length of...

28 S-VIDEO IN RGB IN CONTROL AUDIO OUT AUDIO IN 1 2 RGB OUT 1 2 VIDEO IN AUDIO IN L R MONO Example of system setup Connecting various equipment. AC Inlet Computer(Desk type) Computer (Note type) VTR with S-VHS out (video model only) VTR, etc. (video model only) CRT Display Audio amplifying equipment...

29 ENGLISH Clean the air filter about every 100 hours. Cleaning the air filter Turn the main power switch off and disconnect the powerplug from the power outlet. 1 Remove the front filter cover. 2 Clean the air filter using a vacuum cleaner. • When air filter is very dirty, wash it using neutral det...

30 Lamp Light source lamp has a service life.The picture will become dark or color will be poor when the lamp is used for a long time.If usage of lamp is continued in such cases, it could cause a malfunction. Replace lamp with new one.As reference for replacement time, indicator will operate or mess...

31 ENGLISH Replace the lamp with new one andfix it using the same two screws. • Firmly tighten the lamp screws. Loose screws may causebad connection of the connector which in turn may resultin malfunctioning. 4 Screw Lamp Install the lamp cover and fix it using screws. • To prevent burn, install the...

32 On-screen display The following messages are displayed on the screen. Message table *1 This message are not displayed after 3 minutes. But this message are displayed when you turn on the power again. *2 It is possible to again turn on the power, however the power will go off after about 10 minute...

33 ENGLISH Check the following again before asking for service. If the trouble cannot be recovered, consult your dealer. When you think something wrong • A bright dot may be seen in the picture. This is a phenomenon peculiar to the liquid crystal and is not a problem. • A residual image may occur wh...

34 Specifications All dimensions shown in inches. • All specifications are subject to change without notice. Dimension diagram 1.1 10.1 9.8 2.2 13.0 13.2 3.9 4.2 0.5 Product name Liquid crystal projector Model name CP-S845W Display system 3 sheets of liquid crystal panels, 3 primary color lights shu...