Hitachi CP-S830W/E - Manuals

6 Do not place this unit where it gets hot. Be careful since if you place the unitoutdoors, in a place exposed to directsunlight or near a heating device,the cabinet and parts could beaffected. Cleaning the lens. To clean the lens, use a generally-available lens cleaning tissue (usedfor cleaning len...

7 ENGLISH Main unit Lens Speaker Speaker Remote controlsensor · Use the remote control transmitter withinthe range of about 16 feet from the remotecontrol sensor and within 30 ° to both the left and right. Cooling fan (exhaust) Names and functions of each part Handle ON indicator This blinks in the ...

8 Names and functions of each part (continued) RGB input terminal D-sub 15pin shrink terminal(1/2) VIDEO input terminal (on video-equipped models only) S-VIDEO input terminal Mini DIN 4pin connector(1/2) VIDEO input terminal RCA Jack(1/2) AUDIO L/R input terminal RCA Jack(1/2) AC IN socket Connect t...

9 ENGLISH Remote control transmitter MENU STICK SWITCH When menu screen is being displayed, ana d j u s t m e n t i t e m c a n b e s e l e c t e d a n da d j u s t m e n t c a n a l s o b e d o n e u s i n g t h i sswitch. (See page 14)When menu screen is not displayed, thisswitch can move mouse cu...

10 Caution Cautions on use of batteries · Do not use batteries not specified for this unit. Also do not use old and new batteries together. It may cause a fire, injury due to burst of battery or liquid leakage. · When inserting batteries, pay attention to the direction of the and polarity indication...

Please basically use liquid crystal projector at thehorizontal position. I f y o u u s e l i q u i d c r y s t a l p r o j e c t o r b y t h e l e n s u pp o s i t i o n , t h e l e n s d o w n p o s i t i o n a n d t h e s i d e u pposition, this may cause the heat inside to build up andbecome the ...

12 7 Press the INPUT button or the INPUT SELECT (VIDEO orRGB) button to select the source of the signal to be projectedon the screen. · The selected signal input is displayed at the bottom right of the screen for 3 seconds. Power on all connected equipment. The method of connecting various equipment...

13 ENGLISH Basic operations (continued) · To reduce temperature inside the projector (cooling down), fan will rotate for about 1 minuteafter the lamp is turned off. · Do not turn off the MAIN POWER switch during the lamp on because the lamp is damaged. Press the STANDBY/ON button, for 1 second. · Th...

14 Press the MENU ( ) buttons or the MENU ON / OFF button. · On-screen menus are displayed on the screen. 1 Select the menu to be adjusted using the MENU ( ) buttons or MENU STICK SWITCH. · Menu displayed in green is selected. 2 Select the item to be adjusted using the MENU ( ) buttons or MENU STICK...

15 ENGLISH RGB signal input VIDEO signal input The menu SET UP serves for the change of parameters influencing the picture and for the move picture position. Adjustments and functions (continued) · When start up screen is displayed (''NO INPUT IS DETECTED'' or ''SYNC IS OUT OFRANGE'' is displayed), ...

16 Adjustments and functions (continued) The menu INPUT serves for the selection of input source. The menu IMAGE serves of the picture inversion. S E T U P I N P U T I M A G E O P T . M E S S A G E TURN ONTURN OFF S E T U P I N P U T I M A G E O P T . MIRRORBLANKREVEALMESSAGE S E T U P I N P U T I M...

18 1. Input / output signal Connection to the RGB signal terminal 2. Signal input / output terminal 5 1 10 6 15 11 D-sub 15pin shrink terminal(Female) 1. Input signal Connection to the video signal terminals 2. Signal input terminal Ground Luminance signal S VIDEO input (Mini DIN4 pin) Ground Chromi...

19 ENGLISH 3. Example of computer signal Note 1: Signal mode Note 2: MAC adapter is necessary to the resolution mode. Projector is compatible with 13 inch mode and 16 inch mode. MAC13"mode=switch 1, switch 5 and switch 6 are ON. MAC16"mode=switch 2, switch 5 and switch 6 are ON. Note 3:Displ...

20 4. Initial set signals The following signals are initially set. The settings may be different depending on the computer type. In this case, adjust the settings referring to pages 14, 15. Connection to the RGB signal terminal(continued) Back porch(b) Back porch(b) DATA HSYNC DATA VSYNC Sync.(a) Fr...

21 ENGLISH 1. Control signal terminal Connection to the control signal terminal 2. Mouse emulation 5 1 10 6 15 11 D-sub 15pin shrink terminal (Male) Caution Turn off the power of both the projector and computer before connecting. Connect the computer to the control terminal of the projector using an...

22 Connection to the control signal terminal (continued) PS/2 mouse ADB (Mac) mouse Serial mouse 2 1 4 3 6 5 2 1 4 3 6 5 8 7 10 9 12 11 14 13 15 XA,CLK,SDATA XB,DATA SW-L,SEL0 SW-R,SEL1 READY GND +5V DATA GND+5V CLK TDM YA YB RDP TDP 2 1 4 3 6 5 2 1 4 3 8 7 10 9 12 11 14 13 15 XA,CLK,SDATA TDM SW-R,...

24 Connection to the control signal terminal (continued) Control data table Caution If computer sends the undefined command code or data code, Projector can not guarantee operation. Command is consisted of 2 command bytes and following data bytes. 1-st byte indicates the kinds of commands and the le...

INPUT S-VIDEO VIDEO AUDIO L R 1 1 1 2 2 2 RGB IN AUDIO IN OUT RGB OUT CONTROL 1 2 1 2 26 Example of system setup Connecting various equipment. AC Inlet Computer(Desk type) Computer (Note type) VTR with S-VHS out (video model only) VTR, etc. (video model only) CRT Display Audio amplifying equipment C...

27 ENGLISH Clean the air filter about every 100 hours or when " CHECK THE AIR FLOW " is displayed. Cleaning the air filter Turn the main power switich off and disconnect the powerplug from the power outlet. 1 Remove the air filter from the bottom. 2 Clean the air filter using a vacuum cleane...

28 Lamp Light source lamp has a service life.The picture will become dark or color will be poor when the lamp is used for a long time.If usage of lamp is continued in such cases, it could cause a malfunction. Replace lamp with new one.As reference for replacement time, indicator will operate or mess...

29 ENGLISH Install the lamp cover and fix it using screws. · To prevent burn, install the lamp cover and secure it using screws. · When the lamp cover is out of place, the power does not turn on. Before you turnon the power, make sure to attach the lamp cover and fix it with the scrcws. 5 Lamp (cont...

30 Check the following again before asking for service. If the trouble cannot be recovered, consult your dealer. When you think something wrong A bright dot may be seen in the picture. This is a phenomenon peculiar to the liquid crystal and is not a problem. Message table (continued) The ON indicato...

31 Specifications All dimensions shown in inches. ∑ All specifications are subject to change without notice. Dimension diagram 31 Specifications All dimensions shown in inches. ∑ All specifications are subject to change without notice. Dimension diagram 31 Specifications All dimensions shown in inch...