Hitachi CDR-8130 - Manuals - manualsarea.com

Page 3 - DEFINITIONS AND A SYMBOL

3 CAUTION INVISIBLE LASER RADIATION WHEN OPEN. DO NOTSTARE INTO BEAM OR VIEW DIRECTLY WITH OPTICALINSTRUMENTS. VORSICHT UNSICHTBARE LASERSTRAHLUNG, WENN ABDECKUNGGEÖFFNET. NICHT IN DEN STRAHL BLICKEN AUCH NICHTMIT OPTISCHEN INSTRUMENTEN. ATTENTION RADIATION DU FAISCEAU LASÉR INVISIBLE EN CASD'OUVERT...

Page 4 - IMPORTANT SAFEGUARDS; SAFETY POINTS YOU SHOULD KNOW ABOUT YOUR EQUIPMENT; PRECAUTIONS FOR SAFETY

4 IMPORTANT SAFEGUARDS SAFETY POINTS YOU SHOULD KNOW ABOUT YOUR EQUIPMENT READ ALL INSTRUCTIONS.SAVE THESE INSTRUCTIONS FOR LATER USE.FOLLOW ALL WARNINGS AND INSTRUCTIONS MARKED ON THE PRODUCT. PRECAUTIONS FOR SAFETY Power source -This CD-ROM Drive should be operated from the type of power source in...

Page 5 - Mounting requirements; soft cloth at least once a month.

5 - In a place where an operation temperature reaches beyond the specified temperature 40C - High humidity locations- In a location subject to extreme changes of temperature and humidity- In a room where dust density higher than 0.1 mg/m 3 - In a room that has air conditioning with humidity control ...

Page 6 - CONTROLS AND FUNCTIONS; Rear Panel; Lch

6 CONTROLS AND FUNCTIONS Rear Panel Front Panel (3) (6) (5) (4) (2) (1) (9) 39 40 1 2 (8) (7) (10) (1) LOADING/UNLOADING/BUSY Indicator Indicator blinks green only when the Disc Tray is being opened orclosed, or when the CD-ROM drive is accessing data. (2) Disc Tray When the power of the CD-ROM Driv...

Page 7 - For connecting the power supply cable.; - Mounting screws

7 1 2 4 6 3 5 Circuit Board OR (Default setting) Device isMaster Device isSlave CableSelect (9) ATAPI Interface Connector ATAPI bus connection (40 pin) (10) Power Supply Connector (DC Input) For connecting the power supply cable. 1 2 3 4 +12V GND +5V Circuit Board INSTALLATION WHAT YOU NEED HARDWARE...

Page 8 - SOFTWARE INSTALLATION; Drive, refer to the instruction manual of each CD-ROM device driver.; DRIVE OPERATION

8 Install the CD-ROM Drive following general installation procedure shown below. 1. Check the Device Configuration Jumper settings of the CD-ROM Drive such as Master, Slave, CSEL. (See page 6) 2. Turn off the host computer and unplug the power supply cable of the host computer. 3. Remove the host co...

Page 10 - TROUBLESHOOTING; Push; CAUTION

10 A commercially available "Laser Lens Cleaning Disc" may be used to clean up thepick-up lens of the CD-ROM Drive.Use the Compact Disc Laser Lens Cleaner LLC-1. (by AUDIO SOURCE in U.S.A.,by AKUSTIK SISTEME VERTRIEBS GHBH in GERMANY and by SAECCOMMERCE CO.,LTD. in JAPAN.) (1) Turn on the CD...

Page 11 - Mounting Screw; MECHANICAL DIMENSIONS

11 Symptoms Possible causes Remedy The CD-ROMDrive does notoperate even whena disc is loaded. 1.You place the disc up-side down in the Disc Tray. 2. The disc is dirty.3. The pick-up lens is dirty. 4.The disc is scratched or warped. 5.Cable connection is incorrect. 1.Place the disc right side up in t...

Page 12 - SPECIFICATIONS; GENERAL

12 SPECIFICATIONS GENERAL Power Requirements DC Voltage +12V ±10% 1.0A +5V ±5% 0.7A Ripple +12V 300 mVpp (maximum) +5V 150 mVpp (maximum) Dimensions ( W x H x D ) 146 x 41.3 x 190 mm (Excluding front panel)Front panel : 149.3 x 42.7 x 5 mm Mass 0.95 kg Operating & Storage Conditions Temperature ...