Hitachi 42HDT52 - Manuals
Hitachi 42HDT52 – User Manual, Manual in PDF format online.
Manuals:
User Manual Hitachi 42HDT52
Manual Hitachi 42HDT52
Summary
2 Important Safety Instructions SAFETY POINTS YOU SHOULD KNOW ABOUTYOUR HITACHI PLASMA TELEVISION Our reputation has been built on the quality,performance, and ease of service of HITACHI plasma televisions. Safety is also foremost in our minds in the design ofthese units. To help you operate these p...
4 Accessories First time use Check to make sure you have the following accessories before disposing of the packing material. / CAUTION: 1. Ceiling mounting is not recommended. Mounting the panel on the ceiling does not provide adequate ventilation for the electronics or proper support for the front ...
5 First time use How To Set Up Your New Hitachi Plasma Television Securing to a table-top 1. Using wood screws (two) fasten the set to theclamping screw holes on the rear of the PlasmaDisplay stand as shown below. 2. Using commercially available wood screws, securethe set firmly in position. Securin...
6 How to set up your new HITACHI Plasma Television First time use VIEWING The best picture is seen by sitting directly in front ofthe TV and about 10 to 18 feet from the screen. During daylight hours, reflections from outside lightmay appear on the screen. If so, drapes or screenscan be used to redu...
300-Ohm Twin Lead Cable This outdoor antenna cable must be connected to anantenna adapter (300-Ohm to 75-Ohm). Phono Connector Used on all standard video and audio cables whichconnect to inputs and outputs located on thetelevision’s rear jack panel and side control panel. “F” Type 75-Ohm Coaxial Ant...
8 Quick Reference Remote Control Buttons and Functions First time use POWER BUTTON (TV, DVD, CBL, STB, PVR/VCR, AMP/CD) Turns the selected device on and off. SOURCE ACCESS BUTTONS (TV, DVD, CBL, STB, PVR/VCR, AMP/CD) Changes the mode of the Universal Remot e Control to control the device selected. D...
Antenna Input The remote control allows you to switch betweentwo separate 75-Ohm RF antenna inputs, CABLEand AIR. Audio/Video INPUTS 1, 2, 3 and 4 By using the INPUTS button, the CURSOR PAD ( and ), and the SELECT button or CURSOR PAD of the remote control, you can select each video source. Use the ...
12 Subwoofer Out Connect this SUB WOOFER OUT output to theexternal audio component input using the subwoofer cable (not provided). Upgrade Card This card slot is for future software upgrades.HITACHI will notify you if a software upgrade isrequired for your TV. In order to receive writtennotification...
The front panel jacks are provided as a convenience to allow you to easily connect your video camcorder, digitalcamera or Digital Video Camcorder as shown in the following examples: NOTE: 1. Completely insert connection cord plugs when connecting to left side panel jacks. If you do not, the played b...
• S-VIDEO, YPBPR, or HDMI connections are provided for high performance laserdisc players, VCRs etc. that have this feature. Use these connections in place of the standard video connection if your device hasthis feature. • If your device has only one audio output (mono sound), connect it to the left...
17 Connecting External Video Sources First time use CONNECTING A COMPONENT SOURCE WITHHDMI OR DVI CAPABILITY TO INPUT 1 OR 2 1. Connect the HDMI or DVI output of the HDTVset top box or DVD player to the HDMI input asshown on the Rear panel below. 2. With DVI output, connect the cable from theAUDIO O...
18 Connecting External Video Sources First time use CONNECTING A COMPONENT AND STEREOAUDIO SOURCE TO INPUT 3 OR 4: Y-P B P R . 1. Connect the cable from the Y OUT of theLaserdisc/DVD player or HDTV set top box tothe INPUT (Y) jack, as shown on the Rearpanel below. 2. Connect the cable from the PB/CB...
19 Connecting External Video Sources First time use CONNECTING A COMPONENT SOURCE WITHDIGITAL INTERFACE CAPABILITY TO IEEE1394TERMINALS. 1. Connect the IEEE1394 cable from the output of thecomponent with IEEE1394 capability, such as aDigital VCR or AVHD (External Hard Drive) DigitalRecorder, to the ...
CONNECTING A VIDEO AND MONAURAL AUDIOSOURCE TO INPUT 1, INPUT 2 OR INPUT 5 1. Connect the cable from the VIDEO OUT of theVCR or the laserdisc player to the INPUT(VIDEO) jack, as shown on the Rear Panel on theright. 2. Connect the cable from the AUDIO OUT of theVCR or the laserdisc player to the INPU...
Your Hitachi Plasma Television is equipped with a G-LINK feature. This connection is necessary for the TVGuide On Screen TM system to work with your cable box to receive program listings and to enable VCR recording features. Once you setup the G-LINK (IR Mouse) connector, then you can use your HITAC...
23 The Remote Contr o l In addition to controlling all the functions on yourHITACHI Plasma TV, the new remote control isdesigned to operate different types of VCRs, CATV(Cable TV) converters, set-top-box, satellitereceiver, DVD players, and other audio/videoequipment with one touch. Basic operation ...
24 The Remote Contr o l POWER button Press this button to turn the TV set on or off whenthe remote is in TV mode. (See page 23 forinstructions on how to set the remote control to TVmode.) MODE Indicator Turns on or blinks to show remote control mode. 햴 SOURCE ACCESS ( or ) buttons Press these button...
25 The Remote Contr o l How to Use the Remote to Control Your TV ASPECT button Press this button to quickly change the picture format ASPECT ratio. Depending on the input signal formatreceived, the picture format ratio allows you to adjust the images through the following options. • Antenna-Analog• ...
27 The Remote Contr o l 1. Press the INPUTS button to cycle through theINPUTS selections until the PHOTO INPUT isselected. Press the SELECT button orCURSOR PAD . 2. Press the CURSOR PAD or to access the next or previous photo. 3. Press the SELECT button to viewTHUMBNAIL. 4. Use the CURSOR PAD button...
28 The Remote Contr o l ROTATE Select this menu item to rotate selected photoseither clockwise (CURSOR PAD ) and counterclockwise (CURSOR PAD ). SLIDESHOW Select this menu item to start a slideshow of thedigital photos. While the Interval sub menu ishighlighted, press the SELECT button to cyclethrou...
29 How to Use the Remote to Control Your TV The Remote Contr o l When an IEEE1394 device is not connected When an IEEE1394 device is connected 1. Press INPUT button, CURSOR PAD and SELECT button to select IEEE 1394. 2. Use CURSOR PAD to select connected device (example D-VHS1). 3. Use CURSOR PAD cur...
The Remote Contr o l 30 LAST CHANNEL (LAST CH) button Press this button to toggle between the current andlast channel viewed. VOLUME (VOL) WHEEL, MUTE button Use the VOL WHEEL ( or ) until you obtain the desired sound level. To reduce the sound to one half of normal volume(SOFT MUTE) to answer the t...
The Remote Contr o l 31 Your HITACHI Plasma TV incorporates Two Tunertechnology designed for improved viewing enjoyment.This Two Tuner feature allows you to view antennainputs on both the main picture and sub picturesimultaneously, with separate tuning control for each.When a Digital channel is view...
The Remote Contr o l 33 PAUSE button If you wish to freeze the sub-picture, press thePAUSE button. This is convenient when trying towrite down the address for a mail order company,recording statistics for a sporting event, etc. Toreturn the picture to motion, press the EXITbutton. Press the PAUSE bu...
The Remote Contr o l 34 Operating the precoded function for your cablebox. This remote is designed to operate different types ofcable boxes. You must first program the remote tomatch the remote system of your cable box (refer topages 40-41 for pre-codes). 1. Turn ON your cable box. 2. Aim the remote...
The Remote Contr o l 35 Operating the precoded function for your set-top-box/satellite receiver. This remote is designed to operate different types ofset-top-box/satellite systems. You must first programthe remote to match the remote system of your set-top-box/satellite systems (refer to pages 40-41...
The Remote Contr o l 36 Operating the precoded function for your DVDplayer. This remote is designed to operate different types ofDVD players. You must first program the remote tomatch the remote system of your DVD player (refer topages 40-41 for pre-codes). 1. Turn ON your DVD player. 2. Aim the rem...
Operating the precoded function for yourVCR/PVR (Personal Video Recorder). This remote is designed to operate different types ofVCRs/PVRs. You must first program the remote tomatch the remote system of your VCR/PVR (refer topages 40-41 for pre-codes). 1. Turn ON your VCR/PVR. 2. Aim the remote contr...
The Remote Contr o l 38 Operating the precoded function for your Audiocomponent. This remote is designed to operate different types ofAudio component. You must first program the remoteto match the remote system of your Audio component(refer to pages 40-41 for pre-codes). 1. Turn ON your Audio compon...
The Remote Contr o l 39 INPUT ACCESS This optional feature allows the user of the remotecontrol to setup it’s ENTER (ENT) button to access thespecified input of the TV. Setup for this feature isapplicable to the remote control’s normal mode onlyand only applies to the DVD, CBL, STB, PVR and AMPmodes...
The Remote Contr o l 40 Remote Control Codes VCR BRAND ..................CODE ABS ..................................1972Admiral ....................0048, 0209Adventura .........................0000Aiko....................................0278Aiwa ..............0000, 0037, 0307Akai ..............0041,...
On-Scr een Display 42 1. Press MENU on the remote control to display thedifferent features on your HITACHI Plasma TV. 2. Use the CURSOR PAD (buttons , , and ) or CHANNEL WHEEL to navigate to a different menuitem. 3. Press EXIT on the remote control to quickly exitfrom a menu. On-Screen Display Setup...
On-Scr een Display 43 On-Screen Display Picture Mode Select between the two picture modes; Day and Night. Contrast Adjust contrast. Brightness Adjust brightness. Color Adjust color. Tint Adjust tint. Sharpness Adjust sharpness. Color Temperature Set this to High for less intense color with more blue...
On-Scr een Display 46 Set Black Side Panel The BLACK SIDE PANEL function turns the gray side bars on/off when watching 4:3 signals in Standardmode or use of the PIP modes. 1. Press the CURSOR PAD or to set to ON or OFF. 2. Press EXIT to quit menu or select SET BLACK SIDE PANEL to return to the previ...
47 On-Scr een Display Audio Select AUDIO to adjust the TV to your preference andto improve the sound quality. 1. Press CURSOR PAD or to select menu item. 2. Press CURSOR PAD or to adjust the function. 3. Press EXIT to quit the MENU, or select AUDIO toreturn to the main menu. NOTE: If TREBLE is selec...
On-Scr een Display 48 Audio Source Multi-Channel Television Sound will allow you to select STEREO (a stereo broadcast), MONO (monaural sound) used when receiving a weak stereo broadcast or SECOND AUDIO PROG (SAP) which may be a secondary language, weather report, etc. Internal Speakers This function...
The TV Guide On-Screen system is a built-in featurethat provides a channel lineup and program listings inyour area. Once the setup process is complete, theprogram listings are automatically updated severaltimes a day. This interactive guide can also beprogrammed to receive listings from a cable box ...
Screen 10: The TV Guide On Screen system will test the codeof your Cable box. No TV, Cable or remote buttonsshould be pressed while performing the automatictest. After the testing process is complete, thesetup procedure will continue, see screen 11. Screen 11: Did your Cable box tune to channel 28?U...
54 TV Guide On Screen Using the TV Guide On Screen System This free interactive program guide provides up to 8 days of TV programming. The advanced program listingsmake watching and recording TV shows and programs much easier. The TV Guide On Screen system consists of 5 main services:• Listings: Dis...
NAVIGATING THE TV GUIDE ON SCREEN SYSTEM • Press the GUIDE button while watching TV to access the TV Guide On Screen system. The LISTINGS screen will be presented withthe current show displayed in the Video Window. • Use the CURSOR PAD , , , and to highlight any program, and press the SELECT button ...
56 TV Guide On Screen TV Guide On Screen Icons Icon NAME DESCRIPTION 1. Progress Bar - Elapsed time in current program 2. Info Icon - Indicates Info Box has additional sizes and information. 3. HDTV - Program is presented in High Definition. 4. New - Program is new (not a repeat). 5. CC - Closed Cap...
Five (5) Services: • LISTINGS • SEARCH • RECORDINGS • SCHEDULE • SETUP NOTE : 1. The RECORDINGS service is only available when an IEEE1394 HDD recording deviceis connected to the TV (see page 19). 2. Recording to other devices such as a VCR is available in the LISTINGS, SEARCH andSCHEDULE services. ...
Example: Keyword Search The Keyword search allows you to enter a word orwords to find a program title that matches. 1. From the Search Screen, use the CURSOR PAD or to highlight KEYWORD, and then press the SELECT button. 2. Use the CURSOR PAD or to highlight NEW SEARCH in the Panel Menu, and then pr...
62 • Use Manual Recording: 1. From the SERVICE bar, use the CURSOR PAD or to highlight the SCHEDULE. Press the MENU button to display the Schedule OptionsPanel Menu. 2. Use the CURSOR PAD or to highlight New Manual Recording, and then press the SELECTbutton to access the Record Options Panel Menu. 3...
How to set a reminder: • Set from the Panel Menu 1. Use the CURSOR PAD or to highlight a program and press the MENU button to access theEpisode Options Panel Menu. 2. Use the CURSOR PAD to highlight SET REMINDER and press the SELECT button toaccess the Remind Options Panel Menu. 3. Use the CURSOR PA...
67 TV Guide On Screen On-Scr een Display IR DEFAULTS IR Defaults lets you modify the channel dialing defaultsif your cable box and/or VCR is not changing channelsproperly. 1. From the SETUP screen, use the CURSOR PAD to highlight Change Default Options and then pressthe SELECT button. 2. Use the CUR...
Hitachi Manuals
-
Hitachi WH14DBL
User Manual
-
Hitachi DS14DSFL
User Manual
-
Hitachi L32A104
User Manual
-
Hitachi L32A104
Manual
-
Hitachi CG22EADSL
User Manual
-
Hitachi CG22EASSLP
User Manual
-
Hitachi CG22EAD
User Manual
-
Hitachi CS33EB
User Manual
-
Hitachi C10FCH2
User Manual
-
Hitachi CG22EASL
User Manual
-
Hitachi WH18DSDL
User Manual
-
Hitachi LE49S508
User Manual
-
Hitachi LE49S508
Manual
-
Hitachi CG22EABL
User Manual
-
Hitachi L46S604
User Manual
-
Hitachi L46S604
Manual
-
Hitachi C10FCE2
User Manual
-
Hitachi CG22EASS
User Manual
-
Hitachi CG23ECPSL
User Manual
-
Hitachi DB3DL2
User Manual