Hitachi 240353 - Manuals

308-845 3 WARNING INSTRUCTIONS EQUIPMENT MISUSE HAZARD Equipment misuse can cause the equipment to rupture, malfunction, or start unexpectedly and resultin a serious injury. D This equipment is for professional use only. D Read all the instruction manuals, tags, and labels before operating the equip...

308-845 4 Setup CAUTION This equipment is compatible with most water-basedmaterials. See the wetted parts in the TechnicalData section and your fluid and solventmanufacturer’s compatibility information. Do not use acid catalyzed materials; they are incom-patible with the acetal used in this pump. TO...

308-845 5 Setup Assembling the Wall-Mount Unit See Fig. 1 Install the wall bracket (G) 5 ft (1.5 m) above the floor.For proper hole dimensions, use the Wall MountingHole Layout on page 15. Be sure the wall is strong enough to support the weight of the pump and hoses,any accessories, the fluid, and s...

308-845 6 Operation Using the Gun See the gun instruction manual for gun operation,care, flushing, cleaning, and technical data. Read theentire gun manual before operating the sprayer. Pressure Relief Procedure See Fig. 1 The system remains pressurized until pressure ismanually relieved. To reduce t...

308-845 7 Operation Priming the System See Fig. 1 1. Close the gun air regulator (F). 2. If your system has a fluid pressure regulator (G),close it. 3. Open the bleed-type master air valve (K). 4. Slowly set the pump air regulator (E) pressure to20 to 30 psi (140 to 210 kPa, 1.4 to 2.1 bar). Thepump...

308-845 8 Operation When to Shut Down the System Shut down the system at the end of the work shift andbefore checking, adjusting, cleaning, or repairing thesystem. Always relieve the pressure. WARNING To reduce the risk of serious injury whenever youare instructed to relieve pressure, always follow ...

308-845 9 Maintenance See the separate component instruction manuals for individual component maintenance procedures. Access to some system components requires that you remove the shields. The following steps are for shieldremoval. Shield replacement is the reverse of these steps, so make sure you t...

308-845 10 Parts List Wall-Mount Packages with Fluid Pressure Regulators Model No. 240–349, Delta Spray air spray packageModel No. 240–350, Delta Spray HVLP packageModel No. 240–351, no hoses (31) or gun (30)Model No. 240–352, PRO 3500sc electrostatic packageModel No. 240–353, PRO 4500sc electrostat...

308-845 11 Parts Drawing 13 20 Grounding Detail 19 26 37 8088A 1 8 2 3 5 6 24 24 9 9 10 16 16 17 21 25 29 34 30 31 31 32 33 38 39 40 50 28 7 30 222–300shown 12 27 27 15 15 Wall-Mount Packages with Fluid Pressure Regulators Model No. 240–349, Delta Spray air spray packageModel No. 240–350, Delta Spra...

308-845 12 Parts List Wall-Mount Packages with Surge Tanks Model No. 240–361, Delta Spray air spray packageModel No. 240–362, Delta Spray HVLP packageModel No. 240–363, no hoses (31) or gun (30) Ref.No. Part No. Description Qty. 1 240–210 SHIELD ASSY, front Contains 1a to 1h, shown in Fig. 2 onpage ...

308-845 14 Accessory Fluid Filter Kit Fluid Filter Kit 240–440 Ref.No. Part No. Description Qty. 101 114–361 FILTER, fluid 1 102 113–322 CONNECTOR, male 1 103 054–188 TUBE; PTFE; R 3/8” O.D. 8 in. 104 113–534 ELBOW, male x female 2 105 111–917 NIPPLE; Nylon 1 The Fluid Filter Kit, listed above, can ...

308-845 15 Technical Data Category Data Maximum fluid working pressure 100 psi (0.7 MPa, 7 bar) Maximum incoming air pressure 100 psi (0.7 MPa, 7 bar) Maximum operating temperature 120 _ F (49 _ C) Gun See separate gun instruction manual. Pump See separate pump instruction manual. Fluid pressure reg...