Hitachi 115VIF-3 - Manuals - manualsarea.com

Page 2 - Table of Contents; Document History; Rev B, April 2009 – added 3-position pushbutton pendant control.

Table of Contents Page 2 of 16 Table of Contents Table of Contents................................................................................................................... 2 Chapter 1 – General Description .......................................................................................

Page 3 - Chapter 1; Chapter 1 – General Description; To use the 115VIF-3 interface in an; WARRANTY

Chapter 1 Page 3 of 16 Chapter 1 – General Description The 115VIF-3 interface board is used to translate 115 VAC control signals – from crane and hoist operator pendant stations – to the 24 VDC logical input signals required by the SJ200 or SJ700 series of Hitachi inverters. The board provides optic...

Page 4 - HIGH VOLTAGE; HAZARD OF ELECTRICAL SHOCK. DISCONNECT INCOMING POWER

Chapter 1 Page 4 of 16 SAFETY PRECAUTIONS HIGH VOLTAGE : This symbol indicates high voltage. It calls your attention to items or operations that could be dangerous to you and other persons operating this equipment. Read the message and follow the instructions carefully. WARNING: Indicates a potentia...

Page 5 - Chapter 2; Chapter 2 – Installation and Wiring; Orientation to Product Features; In the standard version of the 115VIF-3,; OUTPUTS

Chapter 2 Page 5 of 16 Chapter 2 – Installation and Wiring Orientation to Product Features Figure 2-1 below shows the physical layout of the 115VIF-3 interface board. Figure 2-1, Board Layout Installing the Interface Board WARNING: Remove power from the inverter and wait at least five minutes before...

Page 6 - INPUT HOIST; NC; Pendant AC

Chapter 2 Page 6 of 16 AC Input Wiring – Connecting the Pendant to the 115VIF-3 Interface Board Connect the pendant 115 VAC input wiring to the terminals marked AC1 through AC5 on the 115VIF-3, with NEU (neutral of the pendant control signals) as their common terminal. AC1 thru AC5 are connected to ...

Page 7 - losest to; Connecting the Board to the Inverter; OUTPUTS2; connector on the board. Align the

Chapter 2 Page 7 of 16 Figure 2-3, 115VIF-3 Correctly Installed in SJ200 Inverter J700 losest to Connecting the Board to the Inverter The method of connection of the 115VIF to the inverter depends on the inverter model. Refer to the appropriate section below for the inverter model you have. SJ200 Th...

Page 8 - no connection

Chapter 2 Page 8 of 16 mounting hole in the board with the threaded insert as shown in the figure. Secure the board to the inverter withe M3 screw supplied with the mounting kit. Connect the pigtail leads to the I/O terminal strip of the SJ700 inverter. Connect the leads one b th y one to intelligen...

Page 9 - Chapter 3; Chapter 3 – Configuring the Inverter; UP; Parameter

Chapter 3 Page 9 of 16 Chapter 3 – Configuring the Inverter The configuration of inverter parameters will depend on the specific functionality and performance required for your application. The basic functionality of the board is designed to interface with a two pushbutton, two-position (two-speed) ...

Page 11 - stops/prevents UP motion – only DOWN motion is possible)

Chapter 3 Page 11 of 16 Alternative Set Ups Two-Speed Operation The inverter can easily be configured for two-speed operation rather than infinitely variable speed operation by using the following parameter settings in lieu of or in addition to those in the table above: Parameter Code Function Setti...

Page 12 - Three-Step Control Wiring

Chapter 3 Page 12 of 16 Three-Step Control Wiring 115VAC HOT Hoist Up (AC1) Hoist Down (AC2) Hold Speed (AC4) Hoist Increase Speed (AC3) Figure 3-1

Page 13 - Chapter 4; Chapter 4 – Operation; Normal Operation; Releasing AC1 at this point will cause the motor speed to ramp down.; Troubleshooting; Inverter will not accelerate beyond minimum speed; Electrical Specifications

Chapter 4 Page 13 of 16 Chapter 4 – Operation Normal Operation Once the inverter parameters are set as described in Chapter 3, you are ready to verify proper operation. It is recommended to first test the system with the motor mechanically disconnected from the crane or hoist, to ensure that any une...

Page 14 - Software State Diagram

Chapter 4 Page 14 of 16 Software State Diagram Ver. 3.7 Version 3.6

Page 15 - Index; AC Input Wiring · 6

Index Page 15 of 16 Index A AC Input Wiring · 6 C Closed-loop · 8 Configuration, inverter · 9 Contents, carton · 3 D DIP switch · 10 E Electrical Specifications · 13 F Faults, resetting · 13 Functionality, basic · 9 H Hoist · 6, 11 I Input functions · 13 Installing · 5 Inverter parameters · 9 J Jump...