HealthRider WESY8630C3 - Manuals

Page 2 - TABLE OF CONTENTS; LIMITED WARRANTY

2 TABLE OF CONTENTS LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

Page 3 - IMPORTANT PRECAUTIONS

3 IMPORTANT PRECAUTIONS WARNING: To reduce the risk of serious injury, read the following important precautions beforeusing the training system. 1. It is the responsibility of the owner to ensure that all users of the training system are ade-quately informed of all precautions. 2. Read all instructi...

Page 4 - BEFORE YOU BEGIN

4 BEFORE YOU BEGIN ASSEMBLED DIMENSIONS: Height: 78 in.Width: 64 in. Length: 70 in. Foot Plate Low PulleyStation High Pulley Station Lat Bar Leg Lever Butterfly Arms Press Arm Weight Stacks Backrests Leg Press Plate Ab Pulley Station WARNING DECAL WARNING DECAL Thank you for selecting the versatile ...

Page 5 - ASSEMBLY

5 ASSEMBLY Make sure you have the following tools: • Two (2) adjustable wrenches • One (1) standard screwdriver • One (1) phillips screwdriver • One (1) rubber mallet • You will also need grease or petroleum jelly, a small amount of soapy water, and clear tape ormasking tape. Note: Assembly will be ...

Page 8 - FRAME

8. Lubricate the insides of the holes in the TopWeights (24) as shown. Slide a Top Weightonto each set of Weight Guides (23). 9. Attach the Top Frame (2) to the Ab Upright (1)with two 5/16” x 2 3/4” Bolts (55), two 5/16”Washers (20), and two 5/16” Nylon Locknuts(40). Do not tighten the Nylon Locknut...

Page 10 - ARM

10 15. Attach a Press Arm (7) to one side of the Press Frame (12) with two 5/16” x 2 1/2” Bolts(39) and two 5/16” Nylon Locknuts (40). Attach the other Press Arm (7) to the PressFrame (12) in the same manner. 16. Press a 1” Round Inner Cap (70) into one of the Press Arms (7). Press a 1 3/4” SquareIn...

Page 11 - CABLE

11 18. Press a 1 3/4” Square Inner Cap (48) into the lower end of the Left Fly Arm (6). Wet thelower end of the Left Fly Arm with soapywater. Slide a 10” Pad (22) onto the Left Arm. Repeat this step with the Right Fly Arm (5). 19. Locate and open the parts bags labeled “CABLE ASSEMBLY” and “PULLEYS....

Page 20 - SEA

51. Locate and open the parts bag labeled “SEAT ASSEMBLY.” Attach the Small Backrest (18) to the AbUpright (1) with two 1/4” x 2 1/2” MachineScrews (64) and two 1/4” Washers (37). 52. Press a 1 1/2” Square Inner Cap (57) into the Rear Seat Frame (16). Insert a 1/4” x 2” Carriage Bolt (61) throughthe...

Page 22 - HOW TO USE THE TRAINING SYSTEM

22 HOW TO USE THE TRAINING SYSTEM The instructions below describe how each part of the training system can be adjusted. Refer to the exerciseposter accompanying this manual to see how the training system should be set up for each exercise. IMPOR-TANT: When attaching the lat bar or nylon strap, make ...

Page 24 - WEIGHT RESISTANCE CHART

24 WEIGHT RESISTANCE CHART This chart shows the approximate weight resistance at each weight station. “Top” refers to the 6.5 lb. top weight.The other numbers refer to the 12.5 lb. weight plates. The butterfly arm resistance listed is the resistance foreach butterfly arm. WEIGHT PRESS BUTTERFLY LEG ...

Page 25 - TROUBLE-SHOOTING AND MAINTENANCE

TROUBLE-SHOOTING AND MAINTENANCE Inspect and tighten all parts each time you use the training system. Replace any worn parts immediately. Thetraining system can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use solvents. TIGHTENING THE CABLES Woven cable, the type of cable us...

Page 26 - CABLE DIAGRAMS

26 CABLE DIAGRAMS The cable diagrams on this page and the next page show the proper routing of the High Cable (85), the LowCable (86), the Rear Cable (87), the Press Cable (88), and the Butterfly Cable (89). Use the diagrams to be surethat the Cables have been assembled correctly. The starting and e...

Page 27 - PLACE

27 Weight Stack—5 High Pulley—1 2 2 3 3 1—Top Frame 4—Weight Stack 4 ICON of Canada Inc.900 de l’IndustrieSt-Jérôme, QuébecCanada, J7Y 4B8 PLACE STAMP HERE High Cable (85) Rear Cable (87)

Page 28 - ORDERING REPLACEMENT PARTS

ORDERING REPLACEMENT PARTS To order replacement parts, simply call our Customer Service Department toll-free at 1-888-936-4266, Mondaythrough Friday, 8 a.m. until 6:30 p.m. EST (excluding holidays). To help us assist you, please be prepared togive the following information: 1. The MODEL NUMBER of th...

Page 35 - EXPLODED DRAWING—Model No. WESY8630C3

1 2 3 4 5 6 7 7 8 9 10 11 12 13 14 15 16 17 18 19 17 21 21 22 22 23 23 24 24 25 25 26 26 27 27 28 28 29 29 29 29 30 31 32 32 33 34 35 36 21 21 85 85 87 86 31 41 41 86 87 88 88 89 89 56 76 82 38 42 20 55 55 76 50 38 40 20 56 42 82 80 43 42 50 40 69 40 69 67 67 40 68 37 44 40 37 68 44 67 40 40 67 42 5...