Hayter 422V - Manuals

SAFETY PRECAUTIONS This safety alert symbol indicates important safety messages. Whenyou see this symbol be alert to the possibility of injury. Carefully readthe following and inform others. Your mower is perfectly safe if used correctly. Failure to observe thefollowing precautions may result in ser...

SAFETY PRECAUTIONS Do not tilt the mower when starting the engine. Do not put hands or feet near or under rotating parts. Never pick up or carry the mower while the engine is running. Never lift the rear deflector while the engine is running. Never touch the exhaust/exhaust guard or cooling fins whe...

Allow the engine to cool before storing in any enclosure. To reduce thefire hazard, keep the engine and the surrounding deck area free ofgrass, leaves, or excessive grease. Check the rear deflector and grassbag frequently for wear or deterioration.Replace worn or damaged parts for safety. If the fue...

To prevent engine damage the engine is shipped without oil orpetrol. The engine must be filled with the correct grade of oil andpetrol before starting the engine. Always use high quality detergent oil classified SAE 30 Oil. Never useadditives with this oil.To prolong the life of your engine it is im...

Operate all control levers several times and ensure that the cablesmove freely. Check that the engine stop and (ground drive clutchlevers - Autodrive model) return freely to their rest position whenreleased. Push the primer button 5 times allowing 2 seconds between each push. Stand behind the mower ...

To make a wide turn steer the mower with the handlebar in the direc-tion required.To make a tight turn (release the ground drive clutch lever, Autodrivemodel), apply downward pressure on the handlebar to raise the frontwheels just above ground level and steer in the required direction. To prevent ac...

OPERATING THE MOWER To prevent accidents thoroughly inspect the area and remove allobjects which when contacted by the cutterblade could becomedangerous projectiles. Inspect the area for hidden obstructionswhich when contacted by the cutterblade could risk health andsafety. Remember the location of ...

There is very little work to do this month apart from brushing awayleaves. Keep off the grass if frozen or waterlogged. Rake the grass thoroughly. Spike the lawn to aerate and stimulate soilorganisms and root growth and apply lawn sand if necessary. The yearly lawn work programme really starts this ...

Use only Briggs & Stratton spark tester (1) to check for a spark asshown in the diagram. Replace the spark plug every 100 hours or every season, whicheveroccurs first. A spark plug wrench is available from any authorisedBriggs & Stratton service dealer. Check the spark plug gap with a feeler...

Assemble the cutterblade (2) with the turned up edges facing towardsthe engine. Secure the cutterblade using the friction washer (3) and newfixing bolt (4) and tighten to a torque of 54Nm. To prevent accidents never reuse the original fixing bolt. Assemble the cutterblade (2) with the turned up edge...

1CG480V25B Storage If the cutterblade is not balanced the heavy end will rotate downwards.Sharpen the heavy end until the cutterblade is correctly balanced. To store the handlebar unscrew the 2 small securing knobs sufficient-ly to allow it to pivot forwards to rest against the mower. Take care toen...

TROUBLE SHOOTING PROBLEM POSSIBLE FAULT REMEDY Engine will not turn over Incorrect oil level. Check oil level. Obstruction under deck. Remove obstruction. Engine smokes Excess oil level. Check oil level. Air cleaner cartridge oil Service air cleaner. soaked or blocked. Engine runs then stops Fuel st...

PROBLEM POSSIBLE FAULT REMEDY Engine vibrates excessively Mounting bolts loose. Tighten bolts Cutterblade bolt loose. Tighten bolt Cutterblade out of balance. Balance cutterblade Bent crankshaft. Consult your dealer Uneven cut Undulating ground conditions Change direction of travel Cutterblade worn ...

DECLARATION OF CONFORMITY 1.28 EC DECLARATION OF CONFORMITY I, the undersigned M.A. Wright, of: HAYTER LIMITED, Spellbrook, Bishop’s Stortford, Herts CM23 4BU ENGLAND certify that the lawnmowers: Models: Jubilee 43 Jubilee 48 Jubilee 48 Push Push Auto Drive Machine Type No. CODE 422V CODE 423V CODE ...

NO. DESCRIPTION PART NO. QTY ITEM NOTE 422V 423V 424V 1 Deck - Mainframe 43. 422069 1 0 0 Deck - Mainframe 48. 424031 0 1 1 2 Engine - Quantum 45. 422054 1 1 0 Engine - Quantum 45. 424021 0 0 1 3 Cover - Wheel 200mm. 422046 2 2 2 4 Nut - M8 Binx. ZNB1H000U 4 4 4 5 Wheel - 200mm. 422044 2 2 0 6 Wheel...

NO. DESCRIPTION PART NO. QTY ITEM NOTE 422V 423V 424V 41 Cover - Lever Height of Cut. 422034 1 1 1 42 Quadrant - Height of Cut. 422035 1 1 1 43 Rivet - Dia. 5/32”. 09317 3 3 3 44 Throw Plate 43. 422028 1 0 0 Throw Plate 48. 423003 0 1 1 45 Stub Axle. 424004 0 0 2 46 Cover - Battery. 422026 1 1 1 47 ...

1D42206B 3 4 7 8 9 22 20 84 32 5 83 82 23 23 22 21 36 29 16 16 55 40 41 22 9 21 5 8 7 4 3 36 42 43 46 36 36 27 4 26 7 8 9 21 16 16 9 7 8 27 4 26 25 25 24 81 44 88 86 86 86 86 422V/423V LOWER MAINFRAME 1.32

422V/423V/424V UPPER MAINFRAME 1.34 1D42201E 305113 64 65 90 51 77 68 77 59 59 2 47 47 50 58 50 60 57 85 56 22 75 79 89 76 67 66 65 74 80 54 53 52 35 63 62 1 69 70 71 72 48 49 61 39 64 38 48 37 78 73 73 73 67 86 86 37 37