Hayter 111-1073 - Manuals

SAFETY RULES 7 1740514 INTERNATIONAL PICTORIALS IMPORTANT: The following pictorials are located on your unit or on literature supplied with the product. Before you operate the unit, learn and understand the purpose for each pictorial. 1 2 6 7 3 8 4 5 9 Safety Warning Pictorials 1 WARNING 2 IMPORTANT...

ASSEMBLY 8 1740514 ASSEMBLYCONTENTS OF PARTS BAG 1 − Owner’s Manual 1 − Parts Bag 1 − Safety Glasses (Not shown actual size) 2 Sets − Trimmer Line 1 − Bag (4 Screws) 1 − 20 oz. Bottle Oil WARNING: Always wear safety glasses or eye shields while as- sembling the machine. TOOLS REQUIRED 1 − Knife to c...

ASSEMBLY 9 1740514 HOW TO RAISE THE HANDLE 1. Hold the handle with one hand and loosen both handle adjustment knobs until the ratchet teeth are disengaged. Do not remove the handle adjustment knobs . See Figure 2. 2. Raise the handle to the operating position. 3. Stand in the operator’s position beh...

ASSEMBLY 10 1740514 ENGINE PREPARATION Note: Engine does not contain OIL or PETROL. WARNING: Follow the engine manufacturer’s instructions for the type of petrol and oil to use. Always use a safety petrol container. Do not smoke when adding petrol to the en- gine. When inside an enclosure, do not fi...

OPERATION 11 1740514 KNOW YOUR POWERTRIM READ THE OWNER’S HANDBOOK AND ALL SAFETY RULES BEFORE YOU OPERATE the machine. To familiarise yourself with the location of the controls, compare the illustrations with your machine. Save this handbook for future reference. Trimmer Head Recoil Starter Handle ...

OPERATION 13 1740514 HOW TO START THE ENGINE NOTE: DO NOT BE ALARMED, your engine will smoke the first time it is started. It is burning off the protective coating that is on the internal engine parts. WARNING: Never leave the ma- chine unattended while the en- gine is running. Wait for the trim- me...

MAINTENANCE 14 1740514 CUSTOMER RESPONSIBILITIES SERVICE RECORDS Fill in dates as you complete regular service. Before Each Use Every 5 Hours Every 25 Hours Every 100 Hours As Noted SERVICE DATES Check Engine Oil Level √ Check trimmer Lines √ 1 Check Trimmer Head Engagement √ Engine/Machine Cleaning...

MAINTENANCE 15 1740514 LUBRICATION How To Lubricate The Jackshaft Assembly A grease fitting is provided to lubricate the jackshaft assembly. Use a grease gun with au- tomotive type grease to lubricate the jackshaft assembly as shown in Figure 10. Figure 10 Grease Fitting How To Change Engine Oil Cha...

MAINTENANCE 16 1740514 SPARK PLUG Check the spark plug every 25 hours. Re- place the spark plug if the electrodes are pitted or burned or if the porcelain is cracked.1. Make sure the spark plug is clean. Clean the spark plug by carefully scraping the electrodes (do not sand blast or use a wire brush...

MAINTENANCE 17 1740514 SERVICE AND ADJUSTMENT WARNING: Before you inspect, clean or service the machine, stop the engine. Make sure that all moving parts have stopped. Disconnect the wire from the spark plug. HOW TO REPLACE THE TRIMMER LINE For the best performance, use a heavy gauge 3.9mm (0.155” d...

MAINTENANCE 18 1740514 HOW TO REPLACE THE DRIVE BELT To replace the drive belt, the trimmer head and shield must be removed as follows. WARNING: Before you remove the drive belt, disconnect the wire from the spark plug. 1. Remove the two fasteners that hold the rear of the shield to the trimmer hous...

MAINTENANCE 19 1740514 STORAGE WARNING: Do not remove petrol while inside a building, near a fire, or while you smoke. Petrol fumes can cause an explosion or a fire. When the machine is put in storage for thirty days or more, follow the steps below to make sure the machine is in good condition the f...

TROUBLE SHOOTING CHART 20 1740514 TROUBLE CAUSE CORRECTION Engine does not start Spark plug wire disconnected. Connect spark plug wire. Engine not primed. Prime engine. Defective or incorrectly gapped spark plug. Inspect or replace spark plug. Fuel tank empty. Add fuel. Dirty carburetor or fuel line...

Code 407E REPAIR PARTS 22 1740514 1 2 3 4 5 28 6 2 7 6 8 4 9 10 9 10 4 11 16 17 11 14 12 15 14 20 22 29 23 27 16 19 30 17 6 20 25 24 26 19 18 18 31 21 32 33 34

Code 407E REPAIR PARTS 23 1740514 Key No. Part No. Description 1 MU740198E701MA Lever, Stop 2 MU323035MA Bolt 3 MU740193MA Cable, Control Latching 4 MU071372MA Tie, Cable 5 MU740196E701MA Handlebar 6 MU15x116MA Nut 7 MU1601039MA Control, Throttle 8 MU672510MA Guide, Rope 9 MU740202MA Knob, Handlebar...

28 1740514 How To Order Replacement Parts Use only manufacturer’s authorised or approved replacement parts. The letter placed on the end of the part number denotes the type of finish for the part, C for chrome, Z for zinc, a PA for purchased assembly. It is important that you include this when order...