Hasselblad 10026 - Manuals

0 319 ° 300 280 260 240 220 200 180 160 140 120 100 80 60 40 20 0 20 40 60 80 100 120 140 160 180 200 220 240 260 280 300 320 340 360 ° 503DGRM1 961018 COPYRIGHT © 1996 ANDERS ENGSTRÖM ANDERS ENGSTRÖM, ILLUSTRATÖRÖstra vägen 46430 91 HÖNÖ tel/fax 031- 96 84 [email protected] October 1996 1:2 Cam...

Tools Camera body 503CW October 1996 Revision 0 Tool No. Description Used for 2:1 V-2200 Bender Signal arm adjustment V-2201 Bender Mirror arm adjustment V-2202 Bender S-arm adjustment V-2203 Bender Release arm adjustment (aux. shutter) V-2205 Bender Supporting tool when using V-2201 V-2206 Winding ...

January 2001 Camera body 503CW Disassembly 3:1 Revision 1 Camera shell Remove the lens, film magazine, view finder, focusingscreen and winding knob. Remove the screw (830060), coupling (22767) andwasher (22799). Remove the leather (13374), shim (22473), screw(822701) and ISO selector knob (22495).Do...

Camera body 503CW Disassembly October 1996 Revision 0 3:3 Focusing screen frame (22812) Remove the two remaining screws (820015) holding thefocusing screen frame to the right hand wall and lift theframe off. Right hand wall (21095-1) Remove (or cut) the foam plastic pad (22582) to getaccess to the t...

DIS10.EPS Camera body 503CW Reassembly May 2000 Revision 1 4:1 The lubricants mentioned in the text are:Grease = Isoflex Topas L32Oil = Isoflex PDP 48 Gear housing (30324) Lubricate carefully the washer (810840) withoil. Lubricate with grease and fit (incl. the abovementioned washer) the ratchet whe...

Camera body 503CW Reassembly May 2000 Revision 1 4:3 Fitting the mechanism plate to the right hand wall On the mechanism plate fit the upper and lowerconnecting rods to the pins on the gear wheels. (13100)for the upper shutter and (13101) for the lower shutter.Lubricate with grease. Position the aux...

Camera body 503CW Reassembly October 1996 Revision 0 4:5 Rear plate (30300) Fitting the rear plate Fig. 23 and 24.Lubricate the shutter driving arm’s shaft hub and themirror’s moving peg with grease. Connect the arm andthe connecting rods and fix the rear plate into thechassis. Ensure that the mirro...

Camera body 503CW Reassembly October 1996 Revision 0 4:6 Front plate (30777) Fitting the front bayonet plate to the camera body Tension the drive spring by turning the outer gear wheelclockwise four turns. The front key will be positioned atthe red index dot.A locking pin can be inserted through the...

Camera body 503CW Adjustment October 1996 Revision 0 5:1 The lubricants mentioned in the text are:Grease = Isoflex Topas L32Oil = Isoflex PDP 48 Install the winding knob V-2206 and tension theauxiliary shutter spring (30384) by releasing the pawl(20919). Turn the knob clockwise and tension thespring...

Camera body 503CW Adjustment October 1996 Revision 0 5:2 Focal length The camera body’s focal length is inspected andadjusted by using tool V-2229. The focal length is71.40 mm ± 0.03 mm. Zero the dial indicator by placing it on surface ”A”.Mount the front plate ”B” into the front bayonet of thecamer...

Camera body 503CW Adjustment October 1996 Revision 0 5:3 Adjustment No. 1 (Overtravel) With the film winding mechanism tensioned, check theangle 15-16 o with the bayonet plate tool 904644 pushed hard against the stop arm (13355). Measure the anglewith a spring tension of 300 gm/cm. Adjust by alterin...

Camera body 503CW Adjustment October 1996 Revision 0 5:4 Adjustment of the release mechanism Check that the release bar (30375) is free from thesignal arm pawl. Adjust by carefully bending theforward part of the signal arm. Use tool V-2200.Minimum free play: 0.2 mm. With the camera fully cocked the ...

Camera body 503CW Adjustment October 1996 Revision 0 5:6 Adjustment of the release sequence Make sure the winding knob V-2206 and the bayonetplate tool 904644 are installed.Release the camera and keep it released by holding therelease bar and push rod back.Move the release bar and push rod to the fr...

Camera body 503CW Adjustment October 1996 Revision 0 5:7 Operate the winding knob V-2206 to cock the shutter.Check that the bayonet plate tool 904644 is blocked bythe stop lever (22769) when the camera is completelycocked. Adjust by bending the front of the lever. The leverengagement should be retai...

Camera body 503CW Adjustment May 2000 Revision 3 Fitting the Circuit board (22575) *22882 CAUTION! When handling the circuit board agrounded bench mat and a wrist strap must beused to prevent ESD damage. Put the insulating plate (22746) in position and placethe circuit board on top of it. Secure the...

Camera body 503CW Adjustment January 2001 Revision 1 5:9 Adjust the lower rear plate/shell alignment and tightenthe two rear screws (829755)and seal with loctite.Fit and tighten the two front screws (820781). Check the upper edge alignment of rear plate and shell.Adjust, if necessary, the two screws...

Camera body 503CW Adjustment January 2001 Revision 1 Check the mirror 45 o angle using the sighting tube which fits in the holder on the gauge. Tighten thelocking screw. Shine a light source towards the ovalcut-out in the upper part of the tube so that the whitering of the ocular is illuminated.When...

Camera body 503CW Adjustment October 1996 Revision 0 5:11 Check the camera functions. Check that the auxiliaryshutter is clear of the internal covers. Check the release sequence using a micrometer V-2354. Mount the micrometer in the exposure button’s cablerelease socket. Carefully screw in the micro...

Camera body 503CW Adjustment June 1998 Revision 1 5:12 Calibration and control of the flash metering system TTL Control/calibration should be carried out each time the camera has been in for repair.The tolerance for the flash meter is ±0.3 EV at all settings. If the Hasselblad Service System 970600 ...

Camera body 503CW Adjustment June 1998 Revision 1 Calibration On pressing the MEASURE button one of the three LED´s will light. The variable resistorin the camera (access behind the leather beside the ISO dial) should be turned so that thegreen LED lights when the MEASURE button is pressed again. If...

Camera body 503CW October 1996 Revision 0 6:1 Front bayonet plate Front plate reassembly Fit the four bayonet tongues (103439) and secure witheight screws (820425).Fit the release button return spring (21096) with onescrew (820015).Behind the front plate glue the two sponge seals(13212) and (13213) ...

Camera body 503CW October 1996 Revision 0 6:3 Auxillary shutter & Mirror Exchanging the mirror (22775) Release the camera.Inside the mirror box, remove the clip "A" anddisengage the arm (22781) from the mirror frame.Remove the washer (810649) located behind the armand the frame.Remove th...

Description PosNo. Pcs SparePart No. Remark Camera body 501C 15:1 October 1996 Revision 0 1 1 40 384 Shell, complete 2 2 22 782 Name plate 3 1 103 592 Leather 4 1 103 529 Accessory rail Spare parts not listed are the same as for 503CW

Description PosNo. Pcs SparePart No. Remark Camera body 501C 15:3 May 1997 Revision 1 Spare parts not listed are the same as for 503CW -3 1 1 30 519 Rear plate, complete State serial No. 2 2 20 958 Mirror assembly 3 1 20 901 Mirror protection 4 3 13 141 Foam plastic pad 5 1 20 854 Mirror 6 1 20 956 ...

Description PosNo. Pcs SparePart No. Remark Camera body 501C 15:5 May 1997 Revision 1 1 1 22 750 Coupling 2 1 22 751 Crank support Spare parts not listed are the same as for 503CW

Description PosNo. Pcs SparePart No. Remark Camera body 503CX 17:2 October 1996 Revision 0 Spare parts not listed are the same as for 503CW 1 1 821 806 Screw 2 1 13 436 Locking washer 3 1 13 163 Bayonet plate 4 1 13 360 Shim, 0.2 mm For adjustment 13360-01, 0.4 mm

COPYRIGHT © 1994 ANDERS ENGSTRÖM ANDERS ENGSTRÖM, ILLUSTRATÖRÖstra vägen 46430 91 HÖNÖ TEL /FAX 031-96 84 64 503CX04.EPS 961031 Camera body 503CX 17:5 October 1996 Revision 0 1 Mounted on the mechanism plate 1 2 3 5 4 6 7 8 9

Description PosNo. Pcs SparePart No. Remark Camera body 501CM 19:3 September 1999 Revision 1 Spare parts not listed are the same as for 503CW 1 2 22 865 Light shield 2 1 22 806 Frame, complete 3 1 22 873 Reflection protector 4 1 22 892 Cover Incl. reflection protector 22 873