Hansgrohe 26396001 - Manuals

Page 2 - ShowerArc; Minimum ceiling height

2 ShowerArc 26396001 Minimum ceiling height – 90 1/2”

Page 3 - Installation Considerations; etc) must be installed before

3 For best results, Hansgrohe recommends that this unit be installed by a licensed, professional plumber.Please read over these instructions thor- oughly before beginning installation. Make sure that you have all tools and sup- plies needed to complete the installation.Inspect the ShowerArc thorough...

Page 4 - Installation in 90o corner:; Instructions begin on page 5; finished; wall, for the hot and cold water supplies for

4 Installation in 90º corner: Instructions begin on page 5 Wall-to-wall installation Requires 26397000 installation kit (included): Instructions begin on page 13. Roughing-in The ShowerArc requires 1/2” NPT female fittings, recessed 3/8” behind the surface of the finished wall, for the hot and cold ...

Page 5 - Installation in 90o corner

5 Only one set of supplies is required – do not install two sets of supplies . Installation in 90º corner The thermostatic mixing valve may be installed on either wall. This diagram shows both possible positions for the installation.

Page 6 - Installation in 90o Corner; Seal the wall around the supplies

6 Installation in 90º Corner Seal the wall around the supplies with waterproof sealant.Failure to seal the wall can lead to possible water damage. 1 2 3 4

Page 8 - Seal the wall around the anchors

8 Seal the wall around the anchors with waterproof sealant.Failure to seal the wall can lead to possible water damage.Be careful not to drill into water lines! 9 10 11 12 6 mm

Page 19 - SW 3 mm

Page 20 - Seal the wall around the an-

20 Install the 26397000 mounting set M6x60 1. 2. 3. SW 3 mm M6x8 25 26 27 6 mm 28 Seal the wall around the an- chors with waterproof sealant.Failure to seal the wall can lead to possible water damage. 1 2

Page 21 - Turn to page 22 to continue the installation.

21 Turn to page 22 to continue the installation. SW 3 mm M6x8 29

Page 23 - Reset the High Temperature Limit Stop; Loosen the handle screw with a 3 mm Allen wrench.

23 Reset the High Temperature Limit Stop Loosen the handle screw with a 3 mm Allen wrench. Remove the retainer clip and stop ring from the stem. Turn the stop unit to the handshower position. Turn the temperature control stem until the output water is the desired high temperature -- usually 110º. KL...

Page 25 - Justify the Handle; Turn the diverter handle to the handshower

25 Justify the Handle Turn the diverter handle to the handshower position. Turn the temperature control knob until the output water is 100ºF.Turn the diverter handle to the off position. Loosen the handle screw with a 3 mm Allen wrench. Remove the handle. Align the indexing mark on the temperature c...

Page 27 - Cleaning the Handshower

27 If necessary, pour about 3/4” of a commercial scale remover, such as Lime-Away or CLR, into a shallow dish. Soak the spray face for the amount of time shown in the label instructions. Rinse the spray face with clear water. Reinstall the handshower. Flush the handshower for at least one minute bef...

Page 28 - Replacement Parts

28 Replacement Parts 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 17 25

Page 30 - Troubleshooting

30 Problem Possible Cause Solution Unit outputs both hot and cold water, but it does not mix not a product defect -- the hot and cold supplies are reversed correct the plumbing Water temperature does not get hot enough high temperature limit stop not set correctly reset high temperature limit stop h...