Grundig 2245 - Manuals - manualsarea.com

Page 2 - WARNING; HIGH PRESSURE SPRAY CAN CAUSE SERIOUS INJURY.; General Safety

WARNING HIGH PRESSURE SPRAY CAN CAUSE SERIOUS INJURY. FOR PROFESSIONAL USE ONLY. OBSERVE ALL WARNINGS. Read and understand all instruction manuals before operating equipment. FLUID INJECTION HAZARD General Safety This pressure washer generates very high fluid pressure.Spray from the gun, leaks or ru...

Page 3 - EQUIPMENT MISUSE HAZARD; HOSE SAFETY

308-489 3 EQUIPMENT MISUSE HAZARD General Safety Any misuse of the pressure washer or accessories, suchas overpressurizing, modifying parts, using incompatiblechemicals and fluids, or using worn or damaged parts,can cause them to rupture and result in fluid injection,splashing in the eyes or on the ...

Page 4 - MOVING PARTS HAZARD; KEEP CLEAR of moving parts when starting or; TERMS; Identifies helpful procedures and information.; IMPORTANT

MOVING PARTS HAZARD Moving parts can pinch or amputate fingers or other bodyparts. KEEP CLEAR of moving parts when starting or operating the pressure washer. NEVER operate the pressure washer without all guardsand interlocks installed and functioning. Follow the Pressure Relief Procedure before chec...

Page 5 - INSTALLATION; Check for Shipping Damage; The water source at the unit

INSTALLATION Figure 1 TEE HANDLE (3040 ONLY) SPRAY GUN SPRAY HOSE HIGH PRESSURE HOSE CONNECTION HOSE RACK INLET WATERCONNECTION 3/4” GARDEN HOSE Check for Shipping Damage The unit should be checked for any damage that mayhave occurred in shipping. Any damage should be notedand the carrier notified i...

Page 6 - STARTUP; NOTE: Some units are equipped with a low–oil sensor; Turn on the water supply.; CAUTION

6 308-489 STARTUP Use this procedure whenever starting the pressurewasher to help insure that the unit is ready to operate andstarting is done safely. 1. Check oil levels. Engine: Add SAE 30 or 10W–30 weight detergent oilas necessary. Pump: Add SAE 20 or 30 weight non–detergent oil asnecessary. NOTE...

Page 7 - ALWAYS engage the trigger safety; Installing and Changing Spray Tips; ALWAYS follow the; Follow the Pressure Relief Procedure.; Tip holding holes are provided on the chassis.

Trigger Safety Latch WARNING To reduce the risk of serious bodily injury,including fluid injection, splashing in the eyes oron the skin, ALWAYS engage the trigger safety latch whenever spraying stops, even for amoment. In the engaged position, the trigger safety latchprevents the gun from being trig...

Page 8 - SHUTDOWN, FLUSHING AND STORAGE; PRESSURE RELIEF PROCEDURE; Engage the trigger safety latch.; MAINTENANCE; Interval; Daily; What to do

SHUTDOWN, FLUSHING AND STORAGE WARNING PRESSURE RELIEF PROCEDURE To reduce the risk of serious bodily injury,including fluid injection and splashing in theeyes, or on the skin, always follow thisprocedure whenever you stop spraying formore than 10 minutes, when shutting down,and before checking or r...

Page 9 - TROUBLESHOOTING CHART; PROBLEM

308-489 9 TROUBLESHOOTING CHART WARNING To reduce the risk of serious bodily injury, including fluid injection, splashing in the eyes or on the skin orinjury from moving parts, always follow the Pressure Relief Procedure Warning before proceeding. PROBLEM CAUSE SOLUTION Low pressure and/orpump runs ...

Page 10 - PARTS DRAWING

10 308-489 PARTS DRAWING 800–062 & 800–063 Hydra–Clean 2245 Pressure Washer 61 1 6966 1 616966 51 49 51 80 74 73 42 66 69 53 60 45 46 47 41 66 69 58 69 57 49 44 2 79 50 13 15 16 56 12 11 14 10 9 8 5 4 71 69 66 66 57 7877 67 70 64 7 66 69 62 3 666971 17 75 72 6 666971 25272931 3682 35 34 21 2281 ...

Page 11 - PARTS LIST

308-489 11 PARTS LIST 800–062 & 800–063 Hydra–Clean 2245 Pressure Washer REF PART NO. NO. DESCRIPTION QTY REF PART NO. NO. DESCRIPTION QTY 1 801–494 ENGINE, 11 HP, Briggs & Stratton I/C (For 800–063 only) 1 801–283 ENGINE, 11 HP, Wisconsin Robin (For 800–062 only) 1 2 800–326 PUMP ASSEMBLY, ...

Page 17 - DESCRIPTION

308-489 17 PARTS LIST 800–326 Pump Assembly, 2200 psi800–327 Pump Assembly, 3000 psi REF PART NO. NO. DESCRIPTION QTY 1 801–467 MANIFOLD, 2200 psi 1 801–647 MANIFOLD, 3000 psi 1 2 801–468 SCREW, Cap, hex hd 8 3 801–469 WASHER, Lock 8 4 : O–RING 5 : SEAT, Valve 6 : PLATE, Valve 7 : SPRING 8 : GUIDE, ...

Page 18 - PUMP SERVICE; Retorque the plug after 5 hours of operation.; Pumping Section; Carefully separate the manifold from the crankcase.; Figure 4

18 308-489 PUMP SERVICE WARNING To reduce the risk of serious bodily injury,including fluid injection, splashing in the eyes oron the skin, or injury from moving parts, alwaysfollow the Pressure Relief ProcedureWarning before proceeding. NOTE: The following metric wrenches are needed:M10, M13 and M3...

Page 19 - Servicing the V–Packings; NOTE: There are two types of packing kits: one is just; Inspect all parts and replace as necessary.; ACCESSORIES

308-489 19 Servicing the V–Packings NOTE: There are two types of packing kits: one is just packings, the other includes the packings,rings and retainers. 1. Remove the manifold as outlined in the PumpingSection. 2. Carefully pull the packing retainer from the manifold.Examine the o–ring and replace ...

Page 20 - THE GRACO WARRANTY

THE GRACO WARRANTY WARRANTY AND DISCLAIMERSGraco warrants all equipment manufactured by it and bearing its name to be free from defects in material andworkmanship on the date of sale by an authorized Graco distributor to the original purchaser for use. Aspurchaser’s sole remedy for breach of this wa...