Goodman TSTATG2111 - Manuals

2 Table of Contents Page iv 1 3 6 7 89 10111213 45 Quick Start Getting to Know Your Thermostat Setting Clock Basic Operation Viewing the Outdoor Temperature Programming the Daily Schedule Thermostat Display OptionsProgramming Run- Time AlertsElectric Heat and Heat Pump Operation Factory Defaults and...

Section 1 Contents: Front Panel Buttons.....................1.2 Display Features...........................1.3 Page 1.1 SECTION 1 Getting to Know Your Thermostat 1 Air Conditionin g & Heatin g






Page 3.1 Section 3 Contents: Setting the Clock..........................3.2 Note: During setup & programming pressing the UP or DOWN buttons will modify the flashing selection. SECTION 3 Setting the Clock 3 Air Conditionin g & Heatin g

Section 4 Contents: Programmable or Non- Programmable Thermostat........4.2 Manual or Auto-Changeover Thermostat..................................4.3 Selecting the Operating Mode.....4.4 Selecting Your Desired Temperature................................4.8 Page 4.1 Note: During setup & programmi...




Section 5 Contents: Viewing the Outdoor Temperature..............................5.2 Page 5.1 SECTION 5 Viewing the Outdoor Temperature 5 Air Conditionin g & Heatin g

Section 6 Contents: Programming a Daily Schedule...................................6.2 Page 6.1 SECTION 6 Programming the Daily Schedule 6 Air Conditionin g & Heatin g


Section 7 Contents: Using the Fan Button.................7.2 Setting the Fan-Off Time Delay..........................................7.3 Page 7.1 SECTION 7 Programming the Fan Operation 7 Air Conditionin g & Heatin g


To increase the cooling efficiency of your unit, the thermostat may be programmed to continue running the fan after a call for cooling has been satisfied. This delay may be set for 30, 60, or 90 seconds. If the Fan Off Delay is set for zero seconds, the fan will not energize after a call for cooling...

Section 8 Contents: Turning On/Off the Backlight...................................8.2 Programming the Thermostat to Display Temperature in Fahrenheit or Celsius..............8.2 Locking/Unlocking the Keypad......................................8.3 Page 8.1 SECTION 8 Thermostat Display Options 8 Air...

Turning On/Off the Backlight Page 8.2 8 Select thermostat operation in degrees F ahrenheit or C elsius. C F Setup Press Press the PROGRAM button to leave the Setup screens. If no buttons are pressed, the display will leave the setup screens after 30 seconds. Programming the Thermostat to Display Tem...


Page 9.1 Section 9 Contents: Setting and Resetting the Service Filter (Fan Run-Time) Alert........................................9.2 Setting and Resetting the UV Light Run-Time Alert.............9.3 SECTION 9 Programming Run-Time Alerts 9 Air Conditionin g & Heatin g









Page 12.1 Section 12 Contents: Resetting the Thermostat to the Factory Default Settings........12.2 Calibrating the Temperature Sensor.....................................12.3 SECTION 12 Factory Defaults and Calibration 12 Air Conditionin g & Heatin g



Description Df Step# Range Step# Description Range - -0 - - - - - -2 62 1 2 3 4 56 7 Programmable ThermostatAuto-Changeover ThermostatFan Off Delay Thermoglow BacklightF or CReset Service Filter IconService Filter Run Time Set Yes Yes 0 Auto F- - 0 Yes/No Yes/No 0, 30, 60, 90Auto/On/OffF/Cread only ...


12 Factory Default Settings (for default values see page 14.1) Page 16.2 Air Conditionin g & Heatin g If, for any reason, you desire to return all the stored settings back to the factory default settings, follow the instructions below. Resetting the Thermostat to the WARNING: This will reset all...