Genie M-4700- Manuals

5 5. GARAGE AND DOOR (cont’d) Sectional Door with Curved Track One-Piece Door with Horizontal Track One-Piece Door with Jamb Hardware without Track One-Piece Door with Pivot Hardware without Track Check the type of door construction you have. The information contained in the figures below will be re...

6 Items shown not actual size. Warranty Card GARAGE DOOR OPENERSAFETY LABELS ANDLITERATURE Straight Door Arm RAIL ASSEMBLY (packed in separate carton) P O W E R H E A D S The following items are included with your Garage Door Opener. All hardware components located in GDO carton. Theaccessories are ...

7 7. IMPORTANT INSTALLATION INSTRUCTIONS IMPORTANT INSTALLATION INSTRUCTIONS TO REDUCE THE RISK OF SEVERE INJURY OR DEATH: 1. READ AND FOLLOW ALL INSTALLATION INSTRUCTIONS. 2. Check with the door manufacturer to determine if additional reinforcement is required to support the door prior to installat...

See Fig. 12 See Fig. 11 Header Door Width VerticalCenter Line Horizontal Line for Header Bracket Height Horizontal Reinforcement Bracket Fig. 10 Identify a sound structural support on header wall abovegarage door for header bracket mounting. See Fig. 11. Ifappropriate header does not exist, replace ...

9 ■ Mark pilot holes location on header through holes wherelag screws will be inserted. IMPORTANT: See Fig. 11 for which header bracket holes to use. ■ Drill 3/16" pilot holes into header, and install bracket withlag screws (5/16 x 1-5/8”) provided. ■ Tighten lag screws firmly. NOTE: Follow the ...

11 ■ Support opener head slightly off the floor. ■ Lift the opposite end of the rail up to the header bracket. ■ Position rail end-stop within the openings in the headerbracket. Insert header clevis pin ( 1/4” dia.) through railend-stop and header bracket, then attach cotter ring toend of pin. (See ...

13 ■ Make sure door is fully closed. ■ Remove tape from rail holding straight door arm (sectional door only) and allow door arm to hang freely. ■ Pull the manual release cord on the trolley to disconnect trolley from chain or belt connector. Slide trolley to posi-tion it about 4" away from the d...

14 To provide the maximum amount of protection, the photoeye must be mounted between 3"and 5" above the floor.See Figs. 28 and 29. M O U N T I N G P H O T O E Y E D I R E C T LY T O W A L L : ■ Locate installation position. See Fig. 28. ■ Mark and drill 1/16" pilot hole into wall. (If mo...

15 ■ Locate position where top mounting screw will go. Marklocation on wall. ■ Drill 1/16" pilot hole into wall. (If mounting to drywall,drill 3/16” pilot hole and use anchors provided). ■ Insert top screw into wall. DO NOT TIGHTEN FLUSH WITHWALL. Leave screw head out approximately 1/8" from...

17 receiver module. (See section 10-16, p. 20). To reduce the risk of electric shock, your opener is providedwith an insulated power cord with a 3-prong groundingplug. The cord must be connected to a standard groundingoutlet. If there is no outlet available at the location, youmust have a qualified ...

18 The control panel is located under the control panel cover. Open the control panel by slightly pulling on the covercutout, then allowing the cover to drop open. The hingesenable the cover to remain in place while you set the adjustments. On control panel you will find 3 buttons labeled “P”, “+”,a...

Up Force 19 Open Travel Limit Setting Adjustment Close Travel Limit Setting Adjustment O P E N T R AV E L L I M I T ( F i g . 3 9 ) : LED #2 should be blinking. You can now set the open travellimit. To move the door to its fully opened position, press andhold the “+” button until the door is in posi...

20 Clear Path between Photo Eyes Photo Eye Receiver(Red Indicator Light on) Photo Eye Transmitter(Green Indicator Light on) Infrared Beam Photo Eye Receiver(Red Indicator Light Off) Photo Eye Transmitter(Green Indicator Light On) ObstructionBreakingInfrared Beam Object directly in Path between Photo...

21 IMPORTANT SAFETY INSTRUCTIONS TO REDUCE THE RISK OF SEVERE INJURY OR DEATH: 1. READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY. 2. Never let children operate or play with door controls. Keep the remote control away from children. 3. Always keep the moving door in sight and away from people and objects...

Transmitterwith ActiveCode NewTransmitter L R L R L R LightBlinks LightBlinks LightOff LightIllunimatesContinuously Press Firstand hold Press Secondand hold Keep Pressed Release whenLight IllunimatesContinuously Midi 2-Channel Transmitter Mounting Plate Visor Clip Fully Assembled 22 T R A N S M I T ...

Your opener can be activated via any of the following,depending on which accessories your opener system has: ■ Remote Control Transmitter ■ Wall Control Panel ■ Doorbell-Type Pushbutton ■ Keyless Entry (optional accessory p.28) R E M O T E C O N T R O L T R A N S M I T T E R : ■ To open or close gar...

24 T O S H O R T E N C H A I N R A I L L E N G T H : ■ Loosen chain tension as much as possible. ■ Remove screws from sprocket holder and rail end-stop. ■ Slide chain and all rail parts out of rail from header end. Seerail exploded view, Fig. 55 on p. 25, for disassembly details. ■ Measure and cut o...

1 2 10 7 5 3 4 Header End Powerhead End 9 8 Item Part # Description 1. ——— Rail 2. 8030339 Sprocket holder assembly 3. 8030432 Roller holder with tension bolt assembly 4. 8008503 Rail end-stop 5. 8030234 Chain connector 6. ——— Chain with position tab Item Part # Description 7. 8030177 Trolley assemb...

26 1 2a 3 6 5 7 2b 2 2a 1 2 12 11 13 14 15 14 2 11 2c 16 10 9 4 5 4 8 15. SYSTEM PARTS (cont’d) M-4700 Power Head Assembly Fig. 56 Item Part # Description 1. 8030589 Lamp Lens 2. 8030329 Wire Harness Assembly 2a. 0047269 Lampsocket w/Wire Harness 2b. 8002875 Terminal Block 2c. 8009963 Varistor 3 ———...

29 L I K E LY C A U S E A N D S O L U T I O N ■ Does opener have electric power? Plug a lamp into the electric outlet to see if lamp turns on. If not,check fuse box or circuit breaker (some outlets are controlled by wall switch). ■ Have you disengaged all locks on door? If not, do so. ■ Has snow or ...

L E D D I S P L AY A F T E R P R E S S I N G “ P ” ■ Remove obstruction from path of door, or realign photo eyes. Refer to page 20. 6 ■ Photo eye became obstructed during downward door travel. ■ Door can be operated normally. Recheck adjustments if adjustment settings were not completed. Refer to pa...

To ensure continued safe operation and extended life of your opener system, periodic checking for proper operation is necessary. Occasional maintenance and readjustment of your system may also be needed. 19. MAINTENANCE AND ADJUSTMENTS Good maintenance of your garage door is an imperative requiremen...

32 PROFESSIONAL SERIES GARAGE DOOR OPENER SYSTEM PROFESSIONAL PRODUCT WARRANTY M-4700 : —Parts Lifetime Warranty* (Labor not included) M-4500 : —Parts (15) Year Warranty* (Labor not included) COVERAGE: Any defect in material and or workmanship from personal, normal household use in accordance with t...