Genie 3452535556 GCG- Manuals

Power Head Assembly 1J 1N 1X 1L 1N 1E 1K 1D 1A 1N 1H 1B 1Q 1G 1D 1F 49 1P 1M 1N 7 Item Part Name Number Required 1 pc. rail 3 pc. rail 1 Power head assembly (box) 1 1 2 Rail assembly (1-piece) (box) 1 3 Rail (1-piece) (box) 1 4 Rail assembly (3-piece)(items 5, 6, 7) (box) 1 5 First rail section (box...

FIG. 1-4 Attach rail strap. 8 OPERATOR ASSEMBLY FOR HELP-1.800.354.3643 OR GENIECOMPANY.COM 1 NOTE: For 1-piece rail—skip to step 4. 1. Identify the rail sections (Fig. 1-1) . • First rail section (attaches to power head). – 2 holes each end. – Half-circle notch 1 end. – Motor end has no notch. • Mi...

FIG. 1-5 Align arrow. FIG. 1-8 Attach emergency release cord & tag. 9 6. Attach rail to power head . • Place rail in front of power head with rail strap at opposite end. • Support door end of rail (rail strap) at about same height as power head. – Check if magnet is in place (Fig. 1-6 inset) . I...

10 10. Attach limit switch wires . • Uncoil limit switch wires. – Place into channels located along top of rail. – Run wires back to power head through hole in topof power head (Fig. 1-12) . – Use wire clips to hold wires in place (Fig. 1-13) . • Attach limit switch wires to terminals on power head ...

FIG. 2-1 Finding highest point of travel (sectional). 11 INSTALLATION FOR HELP-1.800.354.3643 OR GENIECOMPANY.COM 2 I M P O R T A N T 1. READ AND FOLLOW ALL SAFETY, INSTALLATION AND OPERATION INSTRUCTIONS. If you have questions or do not understand an instruction, call The Genie Company or an author...

12 NOTE: If header bracket location needs to beabove header for garage door opening, youneed to add a “mounting surface.” A 2" x 6"board securely attached (fasteners not included)across wall studs on either side of your mark issufficient (Fig. 2-4) . OPEN ORANGE PARTS BAG 2. Mounting the hea...

Mounting Straps [22] 13 MOUNTING THE OPERATOR: 1. Getting Started . • Position rail/power head assembly (Fig. 2-7) . – Rail strap leaning on wall next to header bracket. – Place material on floor under power head to protect from scratching. (A box, stool, or similardevice may be needed to clear a to...

INSTALL DOOR ARMS: Sectional doors OPEN YELLOW PARTS BAG 1. Attach the arms . • Fasten curved door arm to door bracket using clevis pin (24) and cotter pin (25) (Fig. 2-10) . • Straight arm to carriage using clevis pin (24) andcotter pin (25) (Fig. 2-10) . 2. Connecting the arms . • Slide carriage b...

3. Wiring . • Route wire (29) using either method shown (Fig. 3-5) . • Wires along rail are held in place with wire clips. – Wires can be slipped under the wire clips already in place. 15 SAFE-T-BEAM ® SYSTEM INSTALLATION FOR HELP-1.800.354.3643 OR GENIECOMPANY.COM 3 NOTE: The operator will not clos...

FIG. 3-8 Terminal attachments at power head . OPEN RED PARTS BAG 3. Wiring (cont’) . • Securely fasten wires to wall as you go. – Use insulated staples (included). – Staples should be snug only. 16 • Make wire attachments at “ STB ’ s. ” – Splitting and stripping wire ends to be connected as shown (...

FIG. 5-1 Terminal attachments at power head. WALL CONTROL INSTALLATION FOR HELP-1.800.354.3643 OR GENIECOMPANY.COM 4 1. Finding the mounting location . • Pick a convenient location for mounting wall control. – Location you choose should be in direct sight of door. – It should be at least 5' above fl...

18 CONNECTING TO POWER FOR HELP-1.800.354.3643 OR GENIECOMPANY.COM 5 1. Plug the operator into a properly grounded electrical outlet . 2. Check Safe-T-Beam ® alignment (Fig. 6-3) . To reduce the risk of electrical shock, this equipment has a grounded type plug that includesa third ( grounding ) pin....

19 LIMIT SWITCH / FORCE ADJUSTMENT FOR HELP-1.800.354.3643 OR GENIECOMPANY.COM 6 NOTE: During operator cycling for force adjustment, the motor protector may shut offpower to the operator. If this occurs, wait about20 minutes to allow the motor protector to reset. 1. Adjusting limit switches. • Locat...

FCC and IC CERTIFIED 20 PROGRAMMING REMOTE CONTROLS 7 FIG. 8-1 Learn code button and LED 1. Programming . • Locate learn code button and indicator LED on front of power head (under force adjustment screws) (Fig. 8-1) . • Press and release learn code button. – Indicator LED will blink at a rate of tw...

21 MULTI-BUTTON REMOTE 1. Programming . NOTE: Each button on a multi-button remote is designed for use with 1 door. You cannot pro-gram 2 buttons to operate the same door, norcan you program 1 button to operate 2 doors. • For each button . – Program each button separately. – Follow single button rem...

22 IMPORTANT SAFETY INSTRUCTIONS 1. READ AND FOLLOW ALL INSTRUCTIONS. 2. Never let children operate or play with the door controls. Keep the remote control away from children. 3. Always keep the moving door in sight and away from people and objects until the door is completely closed. NO ONE SHOULD ...

23 TROUBLESHOOTING GUIDE (CONTINUED) FOR HELP-1.800.354.3643 OR GENIECOMPANY.COM • Check lock switch on wall console. • Check power source. – Plug a lamp into outlet used for power head If lamp works, power source is OK. – If not, check fuse or circuit breaker. • Power is OK. – Check connections at ...

24 WIRING DIAGRAM FOR HELP-1.800.354.3643 OR GENIECOMPANY.COM Transmitters comply with all United States and Canadian legal requirements as of the date of manufacture. No warranty is madethat they comply with all legal requirements of any other jurisdiction. If transmitters are to be used in another...

A No C.O.D. shipments. Please include check or moneyorder, do not send cash. Allow 3-4 weeks for delivery. We accept Visa or Mastercard phone orders. 1.800.354.3643. Please have part number and creditcard ready. Please add local sales tax if you reside in one ofthe states listed. CaliforniaConnectic...

MODEL DESCRIPTION PRODUCT CODE PRICE (US$)* QTY. TOTAL MODELO DESCRIPCIÓN CÓDIGO PRECIO* CANTIDAD TOTAL MODÈLE DESCRIPTION CODE DU PRODUIT PRIX ($ US)* QTÉ TOTAL Deluxe Remote Control with Intellicode ® GIT-1 Controlador remoto de lujo con Intellicode ® 33069R $34.95 Télécommande de luxe avec Intell...

C The Genie Company Professional Access Systems LIMITED WARRANTY What is covered: Any defect in material and product workmanship from personal, normal household use in accordance with the Owner’s Manual. For how long: H2000C-1 Series - 3 years on Motor, and 1 year on all other parts.350L- 1 Series -...