Genie 2022-T- Manuals

Required Programming 3 NOTE: Before you begin programming, check to make sure there are no objects in the garage door opening. INTRODUCTION Now that your Genie garage door opener is installed, you will want to program the opener so that the door opens and closes properly and all remote devices opera...

TRAVEL LIMITS NOTE: If shuttle/bullet has NOT been engaged to carriage, do so now. See page 17. NOTE: Before setting limits confirm wall console red indicator light (or backlight) is ON. If not illuminated, check for correct wiring or the Sure-Lock switch may be activated. Closing Garage Door (Down ...

Required Programming 3 The DOWN (closed) limit is programmed. Opening Garage Door (Up Limits) NOTE: Beginning with garage door closed is recommended but not necessary. The UP (open) limit is programmed. BOTH DOOR LIMITS ARE NOW PROGRAMMED. PROGRAM SET PROGRAM SET – + 5 Press and release the Program ...

Required Programming 3 Required Programming 3 MODEL AC SR3 THE GENIE COMPANY FCC ID: B8Q AC SR3 Residential Door Operator IC: 2133A-CSD1D 120V. 60HZ. 5A S/N:10XXXX XXXXXXX STB BWC IWC NOT USED NOT USED NOT USED NOT USED FROM STBs FROM WALL CONSOLE STB BWC IWC FROM STBs FROM WALL OM STB ROM WA OM W C...

Required Programming 3 Force and Speed Control These controls are factory programmed and automatically set themselves when you use the Wall Console to open and close the garage door for the first time. The door MUST complete a full cycle from open to close and close to open before it is fully set. N...

Required Programming 3 REMOTES / New Intellicode 2 Openers NOTE: The following instructions are for the remote control transmitters (“Remotes”) provided with this opener. This Remote is preset for use with the Intellicode 2 Access Security System. Refer to page 14 for additional information on Intel...

The Remote button is now programmed. Repeat as necessary for additional Remotes. To program the same Remote for other garage door openers, repeat the steps above using one of the other two Remote buttons. Each Remote can be programmed for three door openers. BASIC PROGRAMMING IS COMPLETE AND YOUR GA...

KEYPAD THE KEYPAD IS PROGRAMMED. Optional Programming 4 A Moving Door can cause serious injury or death. 1 Keep 3 Wall Control should be mounted within sight of door, at least 5 feet above floor and clear of moving parts. people clear of opening while Door is moving. 2 Do Not allow children to play ...

Optional Programming 4 CLEARING MEMORY FOR REMOTES If the memory has been cleared, the Remote will not activate the door opener. NOTE: The garage door opener will operate normally using the Wall Console. NOTE: When the remote is pressed the round LED will flash blue but will not activate the door op...

INTELLICODE 1 REMOTES Remotes provided with this unit can operate other (Intellicode 1) models of Genie garage door openers. The default Intellicode 2 setting must be changed to Intellicode 1. (Follow these same steps to change Intellicode 1 back to Intellicode 2.) NOTE: The button directly above th...

One-Piece Doors 5 ATTACHING DOOR BRACKET TO DOOR NOTE: Center bracket on door as high as possible, preferably top edge . ATTACHING DOOR ARM TO DOOR BRACKET 1 Using bracket, mark holes on door or frame and drill 5/32" hole completely through door frame. Door centerline Door centerline 2 Secure br...

Maintenance and Adjustments 6 If you have any questions, please do not hesitate to contact customer service at: 1-800-35-GENIE or visit www.geniecompany.com IMPORTANT SAFETY INSTRUCTIONS REGULAR MAINTENANCE Basic monthly maintenance tasks include:• Contact Reverse• Safe-T-Beam® System Check• Door ba...

WA R N I N G • Use extreme caution when working from a ladder or step stool.• When replacing light cover, make sure wires are not pinched or near moving parts. Maintenance and Adjustments 6 REGULAR MAINTENANCE (continued) • Screw drive models: Verify shuttle release lever is in ENGAGED (UP) position...

Maintenance and Adjustments 6 C A U T I O N Door closing force is FACTORY set and requires no adjustment for normal operation. • NEVER adjust the force settings to compensate for damage, including an unbalanced door, binding door track, or broken spring.• Perform monthly a CONTACT REVERSE TEST. See ...

Maintenance and Adjustments 6 ADjUSTMENT GUIDES (continued) Speed Settings (DC motors only) Speed settings are pre-programmed at the factory for the maximum speed. Speed settings should not need adjustment with this unit. However, travel speed for the opener can be adjusted to a slower speed in both...

Opener circuit wiring diagram. This wiring diagram is for reference only. Wiring Diagram 7 1 2 3 4 5 6 1 2 3 7 6 POWER CORD CONNECTOR WHITE BLACK GREEN WHITE WHITE BLACK RED BLACK STRIPED WHITE WALL CONSOLE SCREW DRIVE MOTOR STRIPED WHITE SAFE-T-BEAM ® 5 4 3 2 1 (Purchased Separately) INTELLIGENT WA...

Troubleshooting 8 Opener does NOT run from wall console. • Check power source. – Plug a lamp into outlet used for powerhead. If lamp works, power source is OK. – If not, check fuse or circuit breaker. • If power is OK, – Check connections at powerhead terminals and at wall console. – Limits must be ...

Troubleshooting 8 Powerhead LED Possible Problem Solution Round LED Long LED OFF OFF Normal operation. None required. No response from unit. Check power supply. Contact a trained door system technician. ON/RED/ STEADY ON/RED/ STEADY Limits NOT set properly. Re-program limits, see page s 6-7 . ON/RED...

PowerMax ® 1200/1500, SC 1200/1500, TriloG ™ 1200/1500, PowerLift ® 900, GPower ™ 900, SilentMax ® 1000/1200, CB 1000/1200, IntelliG ® 1000/1200 LIMITED WARRANTY GMI Holdings, Inc. d/b/a The Genie Company ("Seller") warrants to the original purchaser of the below identified, SilentMax® 1000/...

Looking for Leading-Edge Technology or the Perfect Update/Replacement? Genie Has the Answer! Leading-Edge Technology 37337R GLRN-R Closed Confirm Wireless Remote (Works with Revolution Series 1500, 1200 and 1000 Models) • Sleek and compact design• Beeps and flashes green when garage door closes. Giv...