Generac Gn - 360 - Manuals

— 5 — G Geen neerraacc G GN N-- 332200//336600//441100 E En ng giin nee OIL AND FUEL INFORMATION NOTE: BE SURE TO READ THESE INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING TO START OR OPERATE THIS EQUIPMENT. Using old or improper oil or fuel can cause engine damage. CAUTION: Any attempt to crank or start ...

G Geen neerraacc G GN N--332200//336600//441100 E En ng giin nee — 6 — OPERATION AND MAINTENANCE It is the owner’s/operator's responsibility to perform all safetychecks; to make sure that all maintenance for safe operation isperformed promptly; and to have the engine checked by anauthorized dealer p...

A If the engine FAILS TO START, go to Step 3. B. If the engine STARTS, go to Step 4. Figure 4 — Recoil Handle 3. Move the choke lever to the HALF CHOKE POSITION,and pull the recoil handle (Figure 4) two (2) times. • If the engine STILL FAILS TO START, repeat Steps 1-3. 4. Move the choke lever to the...

G Geen neerraacc G GN N--332200//336600//441100 E En ng giin nee — 8 — GENERAL MAINTENANCE RECOMMENDATIONS The owner/operator is responsible for making sure that all periodicmaintenance tasks are completed on a timely basis; that all discrepancies are corrected; and that the equipment is kept cleana...

G Geen neerraacc G GN N--332200//336600//441100 E En ng giin nee — 9 — CAUTION: Never run this equipment without the completeair cleaner system installed on the engine. This could resultin premature wear to the engine. Use the following instructions to clean or replace the air cleaner components. 1....

Generac GN-320/360/410 Engine — 10 — Figure 9 — Removing Heat Shield SERVICE AND ADJUSTMENTS ENGINE SPEED CAUTION: The engine speed was properly adjusted at thefactory and should require no additional adjustment. Donot attempt to change engine speed. If you believe theengine is running too fast or t...

3. Loosen the rocker arm jam nut. Using an allen wrench to turnthe pivot ball stud, check the clearance between the rockerarm and the valve stem with a flat feeler gauge (Figure 11). Figure 11 — Adjusting Valve to Rocker Arm Clearance 4. When the valve clearance is correct, hold the pivot ball studw...

G Geen neerraacc G GN N--332200//336600//441100 E En ng giin nee — 12 — RETORQUING THE HEAD BOLTS After the first 50 hours of operation, retorque the head bolts. NOTE: Only perform this adjustment after the first 50 hours of operation. The head bolts will need no further adjustment. 1. Remove the fo...

G Geen neerraacc G GN N--332200//336600//441100 E En ng giin nee — 13 — STORAGE INSTRUCTIONS This engine should be started at least once a week and run for atleast 30 minutes. If this cannot be done and the equipment mustbe stored for more than 30 days, use the following guidelines toprepare it for ...

— 18 — G Geen neerraacc G GN N--332200//336600//441100 E En ng giin nee E EX XP PL LO OD DE ED D V VIIE EW W — — G GA AS S T TA AN NK K M MO OU UN NT TIIN NG G H HA AR RD DW WA AR RE E ITEM PART # QTY. DESCRIPTION 22 40976 2 SHCS M8-1.25 X 20 26 22129 2 Lock Washer M8 94 B2348 1 Tank Cradle 95 52858...

G Geen neerraacc G GN N--332200//336600//441100 E En ng giin nee CALIFORNIA EMISSION CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS The California Air Resources Board ("CARB") and Generac Corporation are pleased to explain the Emission Control SystemWarranty on your new util...

G Geen neerraacc G GN N--332200//336600//441100 E En ng giin nee — 23 — EMISSION CONTROL SYSTEM WARRANTY Emission Control System Warranty ("ECS Warranty") for 1995 and Later Model Year Utility and Lawn and Garden Equipment Engines: A. Applicability: This warranty shall apply to 1995 and late...

G Geen neerraacc G GN N--332200//336600//441100 E En ng giin nee GENERAC POWER SYSTEMS, INC. TWO YEAR LIMITED WARRANTY FOR “GN” ENGINES Generac Power Systems, Inc. warrants to the original purchaser that the engine will be trouble free from defects in materialor workmanship for the items and period ...