Garmin GTP 59 - Manuals - manualsarea.com

Page 2 - RECORD OF REVISIONS; Revision; Initial

Page A G3X Installation Manual Revision A 190-01115-01 © Copyright 2009 Garmin Ltd. or its subsidiaries All Rights Reserved Except as expressly provided herein, no part of this manual may be reproduced, copied, transmitted, disseminated, downloaded or stored in any storage medium, for any purpose wi...

Page 3 - WARNING; INFORMATION SUBJECT TO EXPORT CONTROL LAWS; DOCUMENT PAGINATION; Section Page

G3X Installation Manual Page i 190-01115-01 Revision A WARNING This product, its packaging, and its components contain chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. This Notice is being provided in accordance with California's Proposition 65. If you...

Page 4 - TABLE OF CONTENTS; PAGE

Page ii G3X Installation Manual Revision A 190-01115-01 TABLE OF CONTENTS PARAGRAPH PAGE 1 G3X Installation Overview .............................................................................................................. 1-1 1.1 Unpacking Unit ....................................................

Page 5 - PARAGRAPH

G3X Installation Manual Page iii 190-01115-01 Revision A PARAGRAPH PAGE 5 GTP 59 ............................................................................................................................................. 5-1 5.1 Equipment Description...................................................

Page 7 - LIST OF ILLUSTRATIONS; FIGURE

G3X Installation Manual Page v 190-01115-01 Revision A LIST OF ILLUSTRATIONS FIGURE PAGE 1-1 G3X Interconnect Example .............................................................................................................. 1-2 1-2 Coaxial Cable Installation .......................................

Page 10 - LIST OF TABLES; TABLE

Page viii G3X Installation Manual Revision A 190-01115-01 LIST OF TABLES TABLE PAGE 1-1 G3X LRU Part Numbers .................................................................................................................. 1-3 1-2 Contents of GDU 37X Assembly (010-00667-XX) ...........................

Page 12 - Limited Warranty for Garmin GMU 44 and GTP 59 Products; Street

Page x G3X Installation Manual Revision A 190-01115-01 Limited Warranty for Garmin GMU 44 and GTP 59 Products The Garmin products GMU 44 and GTP 59 are warranted to be free from defects in materials or workmanship for two years from the date of purchase. Within this period, Garmin will at its sole o...

Page 13 - Limited Warranty for GSU 73 and GDU 37X Products

G3X Installation Manual Page xi 190-01115-01 Revision A Limited Warranty for GSU 73 and GDU 37X Products The Garmin products GSU 73 and GDU 37X are warranted to be free from defects in materials or workmanship for one year from the date of purchase. Within this period, Garmin will at its sole option...

Page 14 - GSU 73 HARDWARE MOD LEVEL HISTORY; Improved HSCM accuracy when using +28V supply

Page xii G3X Installation Manual Revision A 190-01115-01 GSU 73 HARDWARE MOD LEVEL HISTORY The following table identifies hardware modification (Mod) Levels for the GSU 73 LRU. Mod Levels are listed with the associated service bulletin number, service bulletin date, and the purpose of the modificati...

Page 15 - G3X Installation Overview; NOTE

G3X Installation Manual – Installation Overview Page 1-1 190-01115-01 Revision A 1 G3X Installation Overview 1.1 Unpacking Unit Carefully unpack the equipment and make a visual inspection of the unit for evidence of damage incurred during shipment. If any component of the G3X system is damaged, noti...

Page 16 - System Overview; GNS

Page 1-2 G3X Installation Manual –Installation Overview Revision A 190-01115-01 1.3 System Overview The G3X is an advanced technology avionics suite designed to integrate pilot/aircraft interaction into one central system. The system combines primary flight instrumentation, aircraft systems instrume...

Page 17 - General G3X LRU Specifications

G3X Installation Manual – Installation Overview Page 1-3 190-01115-01 Revision A 1.4 General G3X LRU Specifications 1.4.1 Garmin LRU Part Numbers Table 1-1. G3X LRU Part Numbers LRU Unit Only Part Number Assembly Part Number GDU 370 Americas DB 011-01747-15 010-00667-15 GDU 370 Atlantic DB 011-01747...

Page 18 - Physical Specifications; Table 1-4. G3X LRU Physical Specifications; Cooling Requirements; No cooling air is required for the GDU 37X

Page 1-4 G3X Installation Manual –Installation Overview Revision A 190-01115-01 1.4.3 Physical Specifications All width, height, and depth measurements are taken with unit rack (if applicable) and connectors. Table 1-4. G3X LRU Physical Specifications LRU Width Height Depth (GMU 44 Diameter, includi...

Page 19 - Installation Requirements; GMU 44, Connector Kit; Item Garmin; Mounting; nominal impedance and meeting applicable aviation

G3X Installation Manual – Installation Overview Page 1-5 190-01115-01 Revision A 1.5 Installation Requirements One GDU 37X assembly (listed in Table 1-1) is required, dependent upon customer’s desired database region. Each GDU 37X (010-00667-XX) comes with all equipment needed for installation. 1.5....

Page 20 - Wiring Harness Installation; Table 1-7. Pin Contact and Crimp Tools Part Numbers; NOTES

Page 1-6 G3X Installation Manual –Installation Overview Revision A 190-01115-01 1.7.1 Wiring Harness Installation Allow adequate space for installation of cables and connectors. Ensure that routing of the wiring does not come in contact with sources of heat, RF or EMI interference. Analog Input wire...

Page 21 - Cable Location Considerations; All cable routing should be kept as short and as direct as possible.; Cable Installation

G3X Installation Manual – Installation Overview Page 1-7 190-01115-01 Revision A 1.7.2 Cable Location Considerations Use cable meeting the applicable aviation regulation for the interconnect wiring. Any cable meeting specifications is acceptable for the installation. When routing cables, observe the...

Page 22 - Backshell Assemblies

Page 1-8 G3X Installation Manual –Installation Overview Revision A 190-01115-01 1.7.4 Backshell Assemblies Connector kits include backshell assemblies. The backshell assembly houses the configuration module and a thermocouple reference junction (if applicable, see Appendix D). Garmin’s backshell con...

Page 23 - Equipment Description; There is no TSO/ETSO applicable to the GDU G37X.; Navigation Functions; Display of position and ground speed

G3X Installation Manual – GDU 37X Page 2-1 190-01115-01 Revision A 2 GDU 37X Figure 2-1. GDU 37X Unit View 2.1 Equipment Description NOTE There is no TSO/ETSO applicable to the GDU G37X. The GDU 37X provides a central display and user interface for the G3X system. The display is mounted flush to the...

Page 24 - Interface Summary; Other GDU 37X; Electrical Specifications; Power Consumption; LRU; GPS Specifications; Characteristics Specifications

Page 2-2 G3X Installation Manual – GDU 37X Revision A 190-01115-01 2.1.2 Interface Summary The GDU 37X uses CAN and RS-232 communications interfaces. The GDU 37X communicates with the following Garmin LRUs: • Other GDU 37X • GSU 73 • SL30 Nav/Comm Transceiver • SL40 Comm Transceiver • GNS 400/500 Se...

Page 25 - Antennas

G3X Installation Manual – GDU 37X Page 2-3 190-01115-01 Revision A 2.2.4 Antennas Table 2-4 lists Garmin and non-Garmin antennas currently supported by the GDU 37X. Refer to Section 6 for Garmin antenna installation information. For non-Garmin antennas, follow the manufacturer’s installation instruc...

Page 26 - Additional Equipment; Figure 2-2. GDU 37X Mounting Accessories

Page 2-4 G3X Installation Manual – GDU 37X Revision A 190-01115-01 2.4 Installation Requirements 2.4.1 Accessories The GDU 37X Connector Kit is provided with the GDU 37X unit and is required to install the unit (Figure 2-2). The GDU 37X Nutplate (115-01054-00) is also supplied with the unit to reinf...

Page 27 - Installation Considerations; Mounting Requirements

G3X Installation Manual – GDU 37X Page 2-5 190-01115-01 Revision A 2.5 Installation Considerations Fabrication of a wiring harness is required. Sound mechanical and electrical methods and practices are recommended for installation of the GDU 37X. Refer to Section 1.6 for wiring considerations and to...

Page 28 - Panel Cutout Template; GDU 37X PANEL CUTOUT TEMPLATE; Cut out panel

Page 2-6 G3X Installation Manual – GDU 37X Revision A 190-01115-01 2.9 Panel Cutout Template The below drawing can be used as a template when marking the panel for cutout. Dimensions below are to verify accuracy of printout only, see Figure C-1.2 for complete dimensions. GDU 37X PANEL CUTOUT TEMPLAT...

Page 29 - T a b l e 3 - 1 . G M U 4 4 E l e c t r i c a l S p e c i f i c a t i o n s; Specification Characteristic; Power Requirements

G3X Installation Manual – GMU 44 Page 3-1 190-01115-01 Revision A 3. GMU 44 Figure 3-1. GMU 44 Unit View 3.1 Equipment Description The Garmin GMU 44 Magnetometer is a remote mounted device that interfaces with a Garmin GSU 73 to provide flight attitude and heading data for flight instrumentation. An...

Page 30 - Environmental Specifications; Table 3-2 lists general environmental specifications.; T a b l e 3 - 2 . G M U 4 4 E n v i r o n m e n t a l S p e c i f i c a t i o n s; Regulatory Compliance; GMU 44 TSO/ETSO Compliance; T a b l e 3 - 3 . T S O / E T S O C o m p l i a n c e; All; T a b l e 3 - 4 . T S O / E T S O D e v i a t i o n s

Page 3-2 G3X Installation Manual – GMU 44 Revision A 190-01115-01 3.3 Environmental Specifications Table 3-2 lists general environmental specifications. T a b l e 3 - 2 . G M U 4 4 E n v i r o n m e n t a l S p e c i f i c a t i o n s Specification Characteristic Regulatory Compliance RTCA/DO-160D E...

Page 31 - T a b l e 3 - 5 . G M U 4 4 P a r t N u m b e r s; No; T a b l e 3 - 6 . G M U 4 4 A c c e s s o r i e s; Installation Rack, GMU 44

G3X Installation Manual – GMU 44 Page 3-3 190-01115-01 Revision A 3.5 Installation Requirements 3.5.1 Equipment Available T a b l e 3 - 5 . G M U 4 4 P a r t N u m b e r s Model Catalog Part Number Unit Part Number Installation Rack GMU 44 010-00296-10* 011-00870-10 No *Included in G3X LRU Kit (K10-...

Page 32 - T a b l e 3 - 7 . R e q u i r e d D i s t a n c e f r o m M a g n e t i c D i s t u r b a n c e s; Disturbance Source; Electric motors and relays, including servo motors

Page 3-4 G3X Installation Manual – GMU 44 Revision A 190-01115-01 T a b l e 3 - 7 . R e q u i r e d D i s t a n c e f r o m M a g n e t i c D i s t u r b a n c e s Disturbance Source Minimum Distance from GMU 44 Electric motors and relays, including servo motors 10 feet (3.0 meters) Ferromagnetic st...

Page 33 - Consideration for Wing Grounded Lighting Fixtures

G3X Installation Manual – GMU 44 Page 3-5 190-01115-01 Revision A 3.6.1 Consideration for Wing Grounded Lighting Fixtures The following installation practices are recommended if the required GMU 44 mounting bracket is located in the wing. 1. The wing tip lights should not have a power ground referen...

Page 34 - Mounting Instructions; not; Maintenance

Page 3-6 G3X Installation Manual – GMU 44 Revision A 190-01115-01 3.8 Mounting Instructions After evaluation of the mounting location has been completed and ensuring that requirements are met, assemble the GMU 44 mounting plate kits according to the dimensions given in Appendix C. Install the unit a...

Page 35 - There is no TSO/ETSO applicable to the GSU 73.

G3X Installation Manual – GSU 73 Page 4-1 190-01115-01 Revision A 4 GSU 73 4.1 Equipment Description NOTE There is no TSO/ETSO applicable to the GSU 73. The GSU 73 is intended for the LSA (light sport aircraft) and experimental aircraft markets. The Garmin GSU 73 Sensor Unit is not a TSO-certified p...

Page 36 - Features Summary; Air Data; Table 4-1. GSU 73 Supply Specifications; Characteristic; Input Voltage Range

Page 4-2 G3X Installation Manual – GSU 73 Revision A 190-01115-01 4.1.1 Features Summary Air Data Interfaces Pressure Altitude CAN (1) Density Altitude RS-232 (2 TX/2 RX) Vertical Speed ARINC 429 (4 RX/2 TX) Mach Number OAT Probe (GTP 59) Indicated Airspeed Magnetometer (GMU 44) (1 RS-232 TX/ 1 RS-4...

Page 38 - Additional Equipment Required; Cables: The installer will fabricate and supply all system cables.

Page 4-4 G3X Installation Manual – GSU 73 Revision A 190-01115-01 Table 4-5. Contents of P732 Connector Kit (011-01818-01)** Item Garmin P/N Quantity Sub-Assy,Backshell w/Hdw,Jackscrew 011-01855-04 1 Connector ,Hi Dens, D-Sub, Mil Crimp 78ck 330-00185-78 1 Contact Pin, Mil Crimp, Size 22D 336-00021-...

Page 39 - Pneumatic Plumbing; Figure 4-2. GSU 73 Air Hose Fitting Locations; Pneumatic Connections; CAUTION

G3X Installation Manual – GSU 73 Page 4-5 190-01115-01 Revision A 4.5.1 Pneumatic Plumbing The GSU 73 has two ports that are connected to the aircraft’s pitot pressure source and static pressure source. The two ports are labeled on the unit (see Figure 4-2). The pressure ports have 1/8-27 ANPT femal...

Page 40 - Figure 4-3. GSU 73 Orientation Calibration

Page 4-6 G3X Installation Manual – GSU 73 Revision A 190-01115-01 4.6 Mounting Requirements Mount the GSU 73 with the connectors aligned within 1.0 deg of either the X or Y axis of the aircraft. The direction of the unit will be accounted for during the calibration procedure as shown in Figure 4-3. ...

Page 41 - Unit Installation; Assemble the wiring harness and backshell connectors.

G3X Installation Manual – GSU 73 Page 4-7 190-01115-01 Revision A Do not use shock mounting to mount the GSU 73. Shock mounts used for other types of inertial systems are not acceptable for the GSU 73 AHRS. The mounting system must have no resonance with the unit installed. Excessive vibration may r...

Page 43 - Item; GTP 59 OAT Probe Kit; GTP 59 OAT Probe

G3X Installation Manual – GTP 59 Page 5-1 190-01115-01 Revision A 5 GTP 59 Figure 5-1. GTP 59 5.1 Equipment Description The Garmin GTP 59 is an outside mounted temperature probe that provides raw air temperature data. The temperature input device is a three-wire temperature probe interface. OAT Powe...

Page 44 - Cables - The installer will supply all system cables.; Applicable LRU; Air Data Computer

Page 5-2 G3X Installation Manual – GTP 59 Revision A 190-01115-01 5.2.1 Additional Equipment Required • Cables - The installer will supply all system cables. 5.3 TSO/ETSO Compliance The following table provides a list of applicable TSO/ETSOs for the GTP 59. Table 5-3. Applicable TSO/ETSOs for the GT...

Page 45 - The following instructions are general guidance.; Table 5-5. Parts Needed for GTP 59 Installation; Ring

G3X Installation Manual – GTP 59 Page 5-3 190-01115-01 Revision A 5.4 Installation Considerations 5.4.1 GTP 59 Icing The GTP 59 OAT probe has no icing protection. If ice accumulates on the GTP 59 OAT probe, its accuracy is unknown. Consequently, air temperature measurements may be incorrect if ice a...

Page 47 - Garmin GPS/XM Antennas

G3X Installation Manual – Antennas Page 6-1 190-01115-01 Revision A 6 Garmin GPS/XM Antennas For non-Garmin antennas, follow the manufacturer’s installation instructions. If using a Garmin GA 26C or GA 26XM, refer to the accompanying installation instructions (190-00082-00 or 190-00522-03). For GA 5...

Page 48 - Table 6-4. XM Satellite Radio Antenna Minimum Requirements; Frequency Range; Antenna Mounting Considerations; Locate the GDU 37X as far as possible from all COM antennas.

Page 6-2 G3X Installation Manual – Antennas Revision A 190-01115-01 Table 6-4. XM Satellite Radio Antenna Minimum Requirements Characteristics Specifications Frequency Range 2332.5 to 2345 MHz Gain (Typical) 24 dB* Noise Figure <1.2 dB Nominal Output Impedance 50 ohms Supply Voltage 3.6 to 5.5 VD...

Page 49 - GPS/XM Antenna Mounting Location; To minimize the effects of shadowing at 5

G3X Installation Manual – Antennas Page 6-3 190-01115-01 Revision A 6.3.2 GPS/XM Antenna Mounting Location The GPS antenna is a key element in the overall system performance and integrity for a GPS navigation system. The mounting location, geometry, and surroundings of the antenna can affect the sys...

Page 50 - Figure 6-1. Recommended Antenna Placement

Page 6-4 G3X Installation Manual – Antennas Revision A 190-01115-01 Figure 6-1 shows the recommended placement of antennas. 4 Figure 6-1. Recommended Antenna Placement

Page 51 - Buried Antenna (below the skin covering or glareshield) Mounting

G3X Installation Manual – Antennas Page 6-5 190-01115-01 Revision A 6.3.3 Buried Antenna (below the skin covering or glareshield) Mounting There are potential performance issues related to buried antennas that the kit builder/installer should be aware of prior to electing to install a buried antenna...

Page 52 - Figure 6-3. Glare Shield Buried Antenna Area; provide adequate GPS reception.; Antenna Doubler/Backing Plate

Page 6-6 G3X Installation Manual – Antennas Revision A 190-01115-01 Mounting the antenna under the glare shield (Figure 6-3) is a good option for XM – FIS antennas, although it is not typically the best option for a GPS antenna. This location results in the aft fuselage shading the antenna. Figure 6...

Page 53 - Teardrop Footprint Antenna Installation (GA 55 and GA 56); Aircraft Skin Thickness; Dimple Dimple; Doubler Preparation for Rivets; Countersink Countersink; Preparation of Doubler

G3X Installation Manual – Antennas Page 6-7 190-01115-01 Revision A 6.4 Teardrop Footprint Antenna Installation (GA 55 and GA 56) This section describes the structural mounting of the teardrop footprint antenna installation. An acceptable installation method is to use Garmin P/N: 115-00846-10 double...

Page 54 - Antenna Installation Instructions

Page 6-8 G3X Installation Manual – Antennas Revision A 190-01115-01 6.4.2 Antenna Installation Instructions 1. Refer to Table 6-5 and the drawings in Appendix C for guidance on selecting the appropriate mounting cutout. Drill or punch the holes to match the mating part (doubler). 2. Install a double...

Page 55 - Reference Figures

G3X Installation Manual – Antennas Page 6-9 190-01115-01 Revision A 6.4.3 Reference Figures Figure 6-4. Doubler Design, Teardrop Footprint Antenna, Skin Thickness 0.032" to 0.049" Figure 6-5. Doubler Design, Teardrop Footprint Antenna, Skin Thickness 0.049" to 0.051"

Page 60 - Skin Thickness

Page 6-14 G3X Installation Manual – Antennas Revision A 190-01115-01 6.5 ARINC 743 Footprint Antenna Installation (GA 55A, GA 57X) This section describes the structural mounting of the ARINC 743 footprint antenna (GA 55A, GA 57X) installation. One acceptable method is to use Garmin P/N: 115-00846-00...

Page 68 - Figure 6-24. Installation of ARINC 743 Footprint Antenna

Page 6-22 G3X Installation Manual – Antennas Revision A 190-01115-01 Figure 6-23. Doubler Installation, ARINC 743 Footprint, Skin Thickness 0.051" to 0.063" Figure 6-24. Installation of ARINC 743 Footprint Antenna

Page 69 - Non-Structural Mount Installation

G3X Installation Manual – Antennas Page 6-23 190-01115-01 Revision A 6.6 Non-Structural Mount Installation This section provides installation examples and considerations for non-structural mounting of teardrop and ARINC 743 footprint antennas. Typical installations may be below a non-metallic glares...

Page 70 - Considerations for Non-Structural Mounting; Figure 6-26. Example Bracket Antenna Mounting Under Glareshield

Page 6-24 G3X Installation Manual – Antennas Revision A 190-01115-01 6.6.2 Considerations for Non-Structural Mounting External mounting of the antenna is preferred, although the antenna can be mounted inside the aircraft. When mounted internally, the antenna does not have to be aligned with the airc...

Page 72 - Non-structural Installation to Airframe

Page 6-26 G3X Installation Manual – Antennas Revision A 190-01115-01 6.6.4 Non-structural Installation to Airframe Internal Non-structural Installation Figure 6-28 and Figure 6-29 show examples of under the fabric skin non-structural mounting of the antenna to the airframe of a tube-and-fabric aircr...

Page 73 - External Non-structural Installation; Figure 6-30. Example Non-structural Antenna Mounting On Airframe

G3X Installation Manual – Antennas Page 6-27 190-01115-01 Revision A External Non-structural Installation Figure 6-30 is an example of an external, non-structural mounting of the antenna in a tube-and-fabric aircraft. The antenna support bracket shown should be made of 2024-T3 Aluminum with a minimu...

Page 74 - Minimum Distance from Metal Tube Structure Requirements; Illustrated Case

Page 6-28 G3X Installation Manual – Antennas Revision A 190-01115-01 Minimum Distance from Metal Tube Structure Requirements Figure 6-31 shows minimum distance from metal tube structure requirements for internal, non-structural mounting of the antenna. Table 6-7 presents minimum distance requirement...

Page 75 - Revision A; Configuration Mode; Turn on the unit in configuration mode.

G3X Installation Manual – Software, Configuration, Databases, and XM Activation Page 7-1 190-01115-01 Revision A 7 Software, Configuration, Databases, and XM Activation 7.1 Configuration Mode Some software loading and all configuration settings are performed in the configuration mode. To enter confi...

Page 76 - Audio Data Identification; Turn on the unit in normal mode.

Page 7-2 G3X Installation Manual – Software, Configuration, Databases, and XM Activation Revision A 190-01115-01 7.2.2 Audio Data Identification Do the following steps to view the unit’s current audio data information: 1. Turn on the unit in normal mode. 2. Press the MENU key twice to display the Ma...

Page 77 - Software Loading Procedure; Menu to update the software.; GSU Software Loading Procedure; Power on the GDU in configuration mode.

G3X Installation Manual – Software, Configuration, Databases, and XM Activation Page 7-3 190-01115-01 Revision A 7.3 Software Loading Procedure Software loading is performed in normal mode. Sections 7.3.1 and 7.3.2 describe the GDU and GSU software load procedure. 7.3.1 GDU Software Loading Procedur...

Page 78 - Configuration Pages

Page 7-4 G3X Installation Manual – Software, Configuration, Databases, and XM Activation Revision A 190-01115-01 7.4 Configuration Pages 7.4.1 Main Configuration Page The Main Configuration Page is used to display LRU (device) specific information such as Unit and System ID’s and Database informatio...

Page 79 - ACFT Configuration Page; In configuration mode, use the FMS Joystick to select the ACFT Page.

G3X Installation Manual – Software, Configuration, Databases, and XM Activation Page 7-5 190-01115-01 Revision A 7.4.2 ACFT Configuration Page The Aircraft Configuration Page allows setting the parameters for Flight Planning, Aircraft Identifier, and Map Symbol. The aircraft’s cruise speed, fuel flo...

Page 80 - In configuration mode, use the FMS Joystick to select the W/B Page.

Page 7-6 G3X Installation Manual – Software, Configuration, Databases, and XM Activation Revision A 190-01115-01 7.4.3 W/B (Weight/Balance) Configuration Page The W/B Configuration Page allows setting the weight and balance parameters for the airplane, these parameters are then used on the Main Menu...

Page 81 - UNITS Configuration Page

G3X Installation Manual – Software, Configuration, Databases, and XM Activation Page 7-7 190-01115-01 Revision A 7.4.4 UNITS Configuration Page The Units Configuration Page allows selection of the desired displayed units for the listed items in the Units Configuration window. The various settings fo...

Page 82 - In configuration mode, use the FMS Joystick to select the DSPL Page.

Page 7-8 G3X Installation Manual – Software, Configuration, Databases, and XM Activation Revision A 190-01115-01 7.4.5 DSPL (Display) Configuration Page The DSPL Configuration Page allows setting the parameters for Display and Backlight Control configuration. 1. In configuration mode, use the FMS Jo...

Page 83 - Display Configuration Window:

G3X Installation Manual – Software, Configuration, Databases, and XM Activation Page 7-9 190-01115-01 Revision A 7.4.5.1 Display Configuration Window: Backlight Intensity: Can be set to Auto or Manual (this setting is also available in normal mode on the Display Setup page). Auto–Sets the backlight ...

Page 84 - SOUND Configuration Page; – Controls the volume level of message tones (settings 1-10)

Page 7-10 G3X Installation Manual – Software, Configuration, Databases, and XM Activation Revision A 190-01115-01 7.4.6 SOUND Configuration Page The SOUND Configuration Page allows setting the parameters for various alert and message tones. 1. In configuration mode, use the FMS Joystick to select th...

Page 85 - COMM Configuration Page; Garmin Data Transfer -

G3X Installation Manual – Software, Configuration, Databases, and XM Activation Page 7-11 190-01115-01 Revision A 7.4.7 COMM Configuration Page The COMM Configuration Page allows setting the parameters for the communication ports. 1. In configuration mode, use the FMS Joystick to select the COMM Pag...

Page 86 - Garmin Database Updates; Equipment required to perform the update is as follows:

Page 7-12 G3X Installation Manual – Software, Configuration, Databases, and XM Activation Revision A 190-01115-01 7.5 Garmin Database Updates The GDU 37X MFD database updates can be obtained by visiting the ‘flyGarmin’ website ( www.fly.garmin.com ). The ‘flyGarmin’ website requires the unit’s Syste...

Page 87 - The unit must be restarted by pressing the Restart softkey.; Available Databases

G3X Installation Manual – Software, Configuration, Databases, and XM Activation Page 7-13 190-01115-01 Revision A 5. When the update process is complete, the screen updates the database status 6. Once the database(s) have been updated, the SD card can be removed from the unit. 7. The unit must be re...

Page 88 - SafeTaxi; Softkey. Record the Radio ID for reference during XM Activation.

Page 7-14 G3X Installation Manual – Software, Configuration, Databases, and XM Activation Revision A 190-01115-01 all obstacles are necessarily charted and therefore may not be contained in the obstacle database. This database is updated on a 56-day cycle. SafeTaxi The SafeTaxi database contains det...

Page 90 - Recommended Test Equipment; Pitot/static ramp tester; GDU 37X Test Procedure; Test the GPS Receiver:; Power on unit and use the FMS Joystick to select the Info Page.

Page 8-2 G3X Installation Manual – Post Installation Checkout and Calibration Procedures Revision A 190-01115-01 8.1 Recommended Test Equipment The following test equipment is recommended to conduct and complete all post installation checkout procedures in this section: (All test equipment should ha...

Page 91 - Power on unit and use the FMS Joystick to select the XM Page.

G3X Installation Manual – Post Installation Checkout and Calibration Procedures Page 8-3 190-01115-01 Revision A Test the XM Receiver (if applicable): 1. Power on unit and use the FMS Joystick to select the XM Page. 2. Verify that the XM receiver is functioning correctly as indicated by the green si...

Page 92 - GSU 73/GMU 44 Post-Installation Calibration Procedures

Page 8-4 G3X Installation Manual – Post Installation Checkout and Calibration Procedures Revision A 190-01115-01 8.3 GSU 73/GMU 44 Post-Installation Calibration Procedures After mechanical and electrical installation of the GSU 73 AHRS and GMU 44 magnetometer have been completed, prior to operation,...

Page 93 - AHRS Calibration Procedure; Table 8-3. Configuration Mode GSU Page Status Boxes; Status Box

G3X Installation Manual – Post Installation Checkout and Calibration Procedures Page 8-5 190-01115-01 Revision A For each Calibration Procedure, Table 8-2 lists the LRU’s that require valid calibration data. Table 8-2. Data Validity Requirements for AHRS Calibration Procedures AHRS Calibration Proce...

Page 94 - Calibration Procedure A: AHRS ORIENTATION; Use the FMS Joystick to select the GSU Page.

Page 8-6 G3X Installation Manual – Post Installation Checkout and Calibration Procedures Revision A 190-01115-01 8.3.1 Calibration Procedure A: AHRS ORIENTATION 1. Enter configuration mode by holding down the left-hand softkey while powering on the GDU 37X. 2. Use the FMS Joystick to select the GSU ...

Page 96 - Use the FMS Joystick to select PITCH/ROLL OFFSET.

Page 8-8 G3X Installation Manual – Post Installation Checkout and Calibration Procedures Revision A 190-01115-01 8.3.2 Calibration Procedure B: Pitch/Roll Offset Compensation by Aircraft Leveling 1. Enter configuration mode by holding down the left-hand softkey while powering on the GDU 37X (if need...

Page 98 - Calibration Procedure C: Magnetometer Calibration; °). It is best to offset the aircraft position; Figure 8-2 – Aircraft Alignment

Page 8-10 G3X Installation Manual – Post Installation Checkout and Calibration Procedures Revision A 190-01115-01 8.3.3 Calibration Procedure C: Magnetometer Calibration NOTE Calibration Procedure B must be successfully completed prior to Calibration Procedure C. NOTE Calibration Procedure C must be...

Page 99 - On the GSU Status Page, use the FMS Joystick to select MAGNETOMER.

G3X Installation Manual – Post Installation Checkout and Calibration Procedures Page 8-11 190-01115-01 Revision A 3. Unlock the GSU Page by pressing softkeys 2, 3, 4 in order (if needed). 4. Ensure that all the required status boxes are checked (Tables 8-2 and 8-3). The GMU 44 and GSU 73 units must ...

Page 100 - increments for the time recommended by the PFD

Page 8-12 G3X Installation Manual – Post Installation Checkout and Calibration Procedures Revision A 190-01115-01 7. Ensure that the aircraft has been properly positioned per the on-screen instructions. 8. Use the FMS Joystick to highlight the Calibrate button at the bottom of the display, press the...

Page 102 - Calibration Procedure D: Heading Offset Compensation

Page 8-14 G3X Installation Manual – Post Installation Checkout and Calibration Procedures Revision A 190-01115-01 8.3.4 Calibration Procedure D: Heading Offset Compensation NOTE Calibration Procedures B and C must have been successfully completed before Calibration Procedure D can be performed. This...

Page 105 - Calibration Procedure E: Engine Run-Up Vibration Test; Use the FMS Joystick to select ENGINE RUN-UP TEST.

G3X Installation Manual – Post Installation Checkout and Calibration Procedures Page 8-17 190-01115-01 Revision A 8.3.5 Calibration Procedure E: Engine Run-Up Vibration Test NOTE Calibration Procedure E is required for all installations to validate the vibration characteristics of the installation. ...

Page 107 - GSU 73 connector not firmly attached to unit.

G3X Installation Manual – Post Installation Checkout and Calibration Procedures Page 8-19 190-01115-01 Revision A e) Absence of mounting supports recommended by the aircraft manufacturer. f) GSU 73 connector not firmly attached to unit. g) Cabling leading to GSU 73 or GMU 44 not firmly secured to su...

Page 108 - Calibration Procedure F: Magnetometer Interference Test

Page 8-20 G3X Installation Manual – Post Installation Checkout and Calibration Procedures Revision A 190-01115-01 8.3.6 Calibration Procedure F: Magnetometer Interference Test NOTE Calibration Procedure F is required for initial installation verification. This test should also be repeated to verify ...

Page 109 - Use the FMS Joystick to select MAGNETOMETER INTERFERENCE TEST.

G3X Installation Manual – Post Installation Checkout and Calibration Procedures Page 8-21 190-01115-01 Revision A 5. Use the FMS Joystick to select MAGNETOMETER INTERFERENCE TEST. 6. Use the FMS Joystick to highlight the Calibrate button, press the ENT Key. 7. Ensure that the aircraft has been prope...

Page 111 - Table 8-4. Magnetometer Interference Test Sequence Example; Elapsed Time Since Start

G3X Installation Manual – Post Installation Checkout and Calibration Procedures Page 8-23 190-01115-01 Revision A Table 8-4. Magnetometer Interference Test Sequence Example Elapsed Time Since Start of Test (min:secs) Action 0:00 Test begins 0:10 Aileron full right 0:20 Aileron full left 0:30 Aileron...

Page 114 - This page intentionally left blank

Page 8-26 G3X Installation Manual – Post Installation Checkout and Calibration Procedures Revision A 190-01115-01 This page intentionally left blank

Page 115 - Troubleshooting

G3X Installation Manual - Troubleshooting Page 9-1 190-01115-01 Revision A 9 Troubleshooting In this section the term ‘Red-X’ refers to a red “X” that appears on different areas of the display to indicate the failure of that particular function. Refer to the G3X Pilot’s Guide (190-01054-00) for a co...

Page 117 - Table 9-1 – GSU 73 AHRS Operating Mode Table

G3X Installation Manual - Troubleshooting Page 9-3 190-01115-01 Revision A 9.3 GSU 73 GSU 73 ground operation is heavily dependent on GPS data inputs. Be sure to correct any GPS performance problems (i.e. interference caused by some types of cell phones or anything that transmits in the area) before...

Page 118 - Attitude/Heading Failure Troubleshooting

Page 9-4 G3X Installation Manual –Troubleshooting Revision A 190-01115-01 9.3.1 Attitude/Heading Failure Troubleshooting Prior to troubleshooting an Attitude Failure on-board the aircraft, gather information from the pilot by asking the following questions. 1. What specifically was the nature of the...

Page 121 - GSU 73 –Air Data Troubleshooting; Check the GTP 59 OAT probe wiring and connection for faults.

G3X Installation Manual - Troubleshooting Page 9-7 190-01115-01 Revision A 9.4 GSU 73 –Air Data Troubleshooting Under normal operating conditions, the GSU 73 provides the following air data information: • Total Air Temperature is measured • Outside Air Temperature (OAT) • Indicated Airspeed (IAS) • ...

Page 122 - Troubleshooting GSU 73 Engine Indication Failures

Page 9-8 G3X Installation Manual –Troubleshooting Revision A 190-01115-01 1. Inspect GSU73 pitot/static plumbing integrity 2. Inspect pitot/static ports and associated equipment 3. If the problem persists replace the GSU 73 with a known good unit 9.4.1 Troubleshooting GSU 73 Engine Indication Failur...

Page 124 - Troubleshooting On-board the Aircraft; Have ground power put on the aircraft.

Page 9-10 G3X Installation Manual –Troubleshooting Revision A 190-01115-01 9.5 Troubleshooting On-board the Aircraft 1. Review the airframe logbook to verify if any G3X or other avionics or electrical maintenance had been performed recently that may have contributed to the failure. 2. Check for loos...

Page 125 - GSU Page

G3X Installation Manual - Troubleshooting Page 9-11 190-01115-01 Revision A 9.6 GSU Page All three status boxes on the GSU Page (config mode) must indicate a positive state (green check marks) before performing any calibration procedures (Section 8). The GMU 44 and GSU 73 units must be communicating...

Page 127 - Return to Service Information; Original GSU 73 is Reinstalled

G3X Installation Manual – Return to Service Page 10-1 190-01115-01 Revision A 10 Return to Service Information These return to service procedures are intended to verify the serviceability of the appliance only. These tests alone do not verify or otherwise validate the airworthiness of the installati...

Page 128 - New GSU 73 Installed; GMU 44 is Reinstalled

Page 10-2 G3X Installation Manual – Return to Service Revision A 190-01115-01 10.2.2 New GSU 73 Installed If a new GSU 73 is installed (new serial number), verify the correct software version on the MAIN page in configuration mode. If the correct software version is not installed, load the GSU 73 so...

Page 129 - APPENDIX A G3X Pinouts; Figure A-1. View of J3701 Connector from Back of Unit; * Indicates Active Low

G3X Installation Manual – Pinouts Page A-1 190-01115-01 Revision A APPENDIX A G3X Pinouts A.1 GDU 37X A.1.1 P3701 Connector PIN 1 PIN 17 PIN 18 PIN 33 PIN 34 PIN 50 Figure A-1. View of J3701 Connector from Back of Unit Pin Pin Name I/O 1 MONO AUDIO OUT HI Out 2 STEREO AUDIO OUT LO -- 3 STEREO AUDIO ...

Page 130 - Pin Pin; Aircraft Power; Pin Name; Mode Selections; GDU Mode

Page A-2 G3X Installation Manual – Pinouts Revision A 190-01115-01 Connector P3701, continued Pin Pin Name I/O 33 CONFIG MODULE CLOCK I/O 34 SIGNAL GROUND -- 35 SIGNAL GROUND -- 36 SIGNAL GROUND -- 37 SIGNAL GROUND -- 38 SPARE -- 39 SPARE -- 40 SPARE -- 41 SPARE -- 42 CDU SYSTEM ID PROGRAM* 4 In 43 ...

Page 131 - Serial Data

G3X Installation Manual – Pinouts Page A-3 190-01115-01 Revision A A.1.4 Serial Data A.1.4.1 RS-232 The RS-232 outputs conform to EIA Standard RS-232C with an output voltage swing of 0-5V when driving a standard RS-232 load. Pin Name Connector Pin I/O RS-232 IN 1 P3701 47 In RS-232 OUT 1 P3701 48 Ou...

Page 132 - Audio

Page A-4 G3X Installation Manual – Pinouts Revision A 190-01115-01 A.1.6 Audio A.1.6.1 Mono Audio Pin Name Connector Pin I/O MONO AUDIO OUT HI P3701 1 Out MONO AUDIO OUT LO P3701 18 -- A.1.6.2 Stereo Audio Pin Name Connector Pin I/O STEREO AUDIO OUT LEFT P3701 3 Out STEREO AUDIO OUT LO P3701 20 -- S...

Page 133 - Power Function

G3X Installation Manual – Pinouts Page A-5 190-01115-01 Revision A A.2 GMU 44 A.2.1 P441 Connector Figure A-2. View of J441 Connector Looking at Rear of Unit Pin Pin Name I/O 1 SIGNAL GROUND -- 2 RS-485 OUT B Out 3 SIGNAL GROUND -- 4 RS-485 OUT A Out 5 SPARE -- 6 POWER GROUND -- 7 SPARE -- 8 RS-232 ...

Page 134 - Connector Description; Figure A-3 Rear View of Connector End Plate; Pin List; Figure A-4 Rear Connector J731 Viewed from Connector End of Unit

Page A-6 G3X Installation Manual – Pinouts Revision A 190-01115-01 A.3 GSU 73 A.3.1 Connector Description The GSU 73 has one 62-pin connector (J731) and one 78-pin connector (J732) located on the connector end of the unit, as shown below. J731 and J732 are clearly marked on the connector end plate. ...

Page 135 - Connector P731, continued

G3X Installation Manual – Pinouts Page A-7 190-01115-01 Revision A Connector P731, continued Pin Pin Name I/O 16 RS-232 IN 2 In 17 RS-232 OUT 2 Out 18 RS-232 IN 3 In 19 RS-232 OUT 3 Out 20 ARINC 429 OUT 1 A Out 21 ARINC 429 OUT 1 B Out 22 ARINC 429 OUT 2 A Out 23 ARINC 429 OUT 2 B Out 24 SIGNAL GROU...

Page 136 - Figure A-5 Rear Connector J732 Viewed from Connector End of Unit

Page A-8 G3X Installation Manual – Pinouts Revision A 190-01115-01 A.3.2.2 P732 Connector Figure A-5 Rear Connector J732 Viewed from Connector End of Unit Pin Pin Name I/O 1 ANALOG IN 2 LO In 2 ANALOG IN 3 HI In 3 ANALOG IN 8 LO In 4 ANALOG IN 9 LO In 5 ANALOG IN 14 LO In 6 ANALOG IN 17 LO In 7 ANAL...

Page 137 - Connector P732, continued

G3X Installation Manual – Pinouts Page A-9 190-01115-01 Revision A Connector P732, continued Pin Pin Name I/O 40 ANALOG IN 4 LO In 41 ANALOG IN 1 LO In 42 ANALOG IN 10 LO In 43 ANALOG IN 7 LO In 44 ANALOG IN 15 LO In 45 ANALOG IN 16 LO In 46 ANALOG IN 25 LO In 47 ANALOG IN 22 HI In 48 ANALOG/CURRENT...

Page 138 - The GSU 73 has four inputs for aircraft power bus inputs of 14/28Vdc.; Transducer Output Power; The GSU 73 outputs supply voltage to the GMU 44 via pins 38 & 39.; GSU System ID Program

Page A-10 G3X Installation Manual – Pinouts Revision A 190-01115-01 A.3.3 Power I/O A.3.3.1 Aircraft Power The GSU 73 has four inputs for aircraft power bus inputs of 14/28Vdc. Pin Connector Pin Name I/O 47 P731 AIRCRAFT POWER 1 IN 49 P731 AIRCRAFT POWER 2 IN 59 P731 POWER GROUND -- 61 P731 POWER GR...

Page 139 - Serial Data Electrical Characteristics

G3X Installation Manual – Pinouts Page A-11 190-01115-01 Revision A A.3.5 Serial Data Electrical Characteristics A.3.5.1 ARINC 429 Input/Output The ARINC 429 outputs conform to ARINC 429 electrical specifications when loaded with up to 5 standard ARINC 429 receivers. Pin Connector Pin Name I/O 20 P7...

Page 140 - CAN Bus; The GSU 73 has 4 configurable discrete inputs conforming to:

Page A-12 G3X Installation Manual – Pinouts Revision A 190-01115-01 A.3.5.3 RS-485 Input The GSU 73 contains one channel of RS-485 serial data communications. Pin Connector Pin Name I/O 1 P731 MAGNETOMETER RS-485 IN B IN 2 P731 MAGNETOMETER RS-485 IN A IN A.3.5.4 CAN Bus This data bus conforms to th...

Page 141 - Discrete Outputs; Vout; Pin Connector; DISCRETE; Analog Input Configuration; Configurable Parameter; When Disabled

G3X Installation Manual – Pinouts Page A-13 190-01115-01 Revision A A.3.6.2 Discrete Outputs INACTIVE: Floating (can be pulled up to externally sourced Vout in the range 0 ≤  Vout ≤  33VDC) Leakage current in the INACTIVE state is typically ≤ 10 uA to ground ACTIVE: Vout ≤ 0.5VDC with ≤  20 mA si...

Page 142 - or less between ground and the Analog; continued

Page A-14 G3X Installation Manual – Pinouts Revision A 190-01115-01 NOTE If installing an ungrounded thermocouple to an Analog In input, a DC reference must be added to the LO input. This can be accomplished by adding a resistance of 1 M Ω or less between ground and the Analog In LO input that the u...

Page 143 - Temperature Inputs; for the temperature probe; Frequency Counter Inputs; Vdc or the resistance to ground is

G3X Installation Manual – Pinouts Page A-15 190-01115-01 Revision A Pin Connector Pin Name I/O 47 P732 ANALOG IN 22 HI IN 67 P732 ANALOG IN 22 LO IN 28 P732 ANALOG IN 23 HI IN 8 P732 ANALOG IN 23 LO IN 27 P732 ANALOG IN 24 HI IN 7 P732 ANALOG IN 24 LO IN 66 P732 ANALOG IN 25 HI IN 46 P732 ANALOG IN ...

Page 144 - Fuel Select Outputs

Page A-16 G3X Installation Manual – Pinouts Revision A 190-01115-01 The following table lists the minimum frequency, maximum frequency, and duty cycles for each of these inputs. Pin Name Minimum Frequency Maximum Frequency Duty Cycle FREQUENCY COUNTER IN* 1 1 Hz 500 Hz/100 KHz* 50% FREQUENCY COUNTER...

Page 145 - APPENDIX B Connector Installation Instructions; Figure Ref; ” Thermocouple, K type

G3X Installation Manual – Appendix B Page B-1 190-01115-01 Revision A APPENDIX B Connector Installation Instructions B.1 Thermocouple Installation into a Backshell Table B-1 lists parts needed to install a Thermocouple. Parts for this installation are included in the Thermocouple Kit (011-00981-00),...

Page 146 - Figure B-2. Jackscrew Backshell Thermocouple Installation

Page B-2 G3X Installation Manual – Appendix B Revision A 190-01115-01 Figure B-2. Jackscrew Backshell Thermocouple Installation

Page 147 - cond. Cable harness

G3X Installation Manual – Appendix B Page B-3 190-01115-01 Revision A B.2 Jackscrew Configuration Module Installation into a Jackscrew Backshell Tables B-2 & B-3 list parts needed to install a Jackscrew Configuration Module with pins or with sockets. Parts for these installations are included in...

Page 149 - Figure B-4. Jackscrew Backshell Installation

G3X Installation Manual – Appendix B Page B-5 190-01115-01 Revision A Figure B-4. Jackscrew Backshell Installation

Page 150 - Jackscrew Backshell Installation Instructions

Page B-6 G3X Installation Manual – Appendix B Revision A 190-01115-01 B.3 Jackscrew Backshell Installation Instructions B.3.1 Shield Block Installation Parts Tables B-4 and B-5 list the parts needed to install a Shield Block. Parts listed in Table B-4 are supplied in the jackscrew backshell kits (01...

Page 152 - Table B-6. Shielded Cable Preparations for Garmin Connectors; Suggested tools to accomplish the window cut:

Page B-8 G3X Installation Manual – Appendix B Revision A 190-01115-01 B.3.2 Shield Termination Technique – Method A.1 (Standard) NOTE For the following steps please refer to the drawings showing the installation of a Jackscrew Backshell. 1. The appropriate number of Jackscrew Backshells will be incl...

Page 153 - Solder Sleeves with pre-installed Flat Braid; Raychem recommended heating tools:; Individual solder sleeves and Flat Braid

G3X Installation Manual – Appendix B Page B-9 190-01115-01 Revision A 3. Connect a Flat Braid (item 4) to the shield exposed through the window of the prepared cable assembly (item 2) from step 2. The Flat Braid should go out the front of the termination towards the connector. It is not permitted to...

Page 154 - Teflon Heat Shrinkable Tubing:

Page B-10 G3X Installation Manual – Appendix B Revision A 190-01115-01 Secondary Method: Solder a Flat Braid (item 4) to the shield exposed through the window of the prepared cable assembly (item 2). Ensure a solid electrical connection through the use of acceptable soldering practices. Use care to ...

Page 159 - Figure B-11. Daisy Chain between Methods A and B

G3X Installation Manual – Appendix B Page B-15 190-01115-01 Revision A B.3.6. Daisy Chain between Methods A and B In rare situations where more braids need to be terminated for a connector than three per ring terminal and a mixture of Methods A and B have been used, it is allowable to daisy chain a ...

Page 160 - All other restrictions set forth for in Table B-8 are applicable.; Table B-8. Shielded Cable Preparations for Garmin Connectors

Page B-16 G3X Installation Manual – Appendix B Revision A 190-01115-01 B.3.7 Double-Shield Termination Technique - Method C.1 In rare situations where double shielding may be necessary, the outer shield should be grounded at both ends, while the inner shield should be grounded only at one end. All o...

Page 161 - Termination

G3X Installation Manual – Appendix B Page B-17 190-01115-01 Revision A B.3.8 Double-Shield Termination Technique (Quick Term) - Method C.2 In addition to method C.1, described previously, another suitable method for double-shielding wires is presented in Figure B-13. All restrictions set forth for M...

Page 163 - Circular Connector Installation Instructions

G3X Installation Manual – Appendix B Page B-19 190-01115-01 Revision A B.4 Circular Connector Installation Instructions B.4.1 Pigtail Installation Parts Table B-9 provides a list of parts needed to install a circular connector with backshell. Parts for this installation are included in the pigtail c...

Page 164 - B.4.2 Standard Shield Termination Technique – Method A; Figure B-16. Standard Shield Termination

Page B-20 G3X Installation Manual – Appendix B Revision A 190-01115-01 NOTE In Figure B-15, “AR” denotes quantity “As Required” for the particular installation. Figure B-15. Circular Connector Install (19 contact example) B.4.2 Standard Shield Termination Technique – Method A Figure B-16. Standard S...

Page 165 - Table B-11. Shielded Cable Preparations for Garmin Connectors; Recommended Solder Sleeve

G3X Installation Manual – Appendix B Page B-21 190-01115-01 Revision A Table B-11. Shielded Cable Preparations for Garmin Connectors Float (in) Window (in) Backshell Size Insert Arrangement Min Max Ideal Min Max Ideal 14 19 1.35 1.60 1.50 2.10 4.60 3.60 1. At one end of a shielded cable (item 4) mea...

Page 168 - B.4.3 Daisy Chain Shield Termination Technique – Method A

Page B-24 G3X Installation Manual – Appendix B Revision A 190-01115-01 B.4.3 Daisy Chain Shield Termination Technique – Method A In rare situations where more braids need to be terminated for a connector than three per ring terminal it is allowable to daisy chain a maximum of two shields together be...

Page 169 - B.4.4 Quick Term Shield Termination – Method B

G3X Installation Manual – Appendix B Page B-25 190-01115-01 Revision A B.4.4 Quick Term Shield Termination – Method B If desired, the drain wire termination (item 5) and the floating shield termination (item 7) can be effectively combined into a “Quick Term”. This method eliminates the float in the ...

Page 172 - B.4.6 Daisy Chain Shield Termination Between Methods A and B; Figure B-21. Daisy Chain Shield Termination between Methods A and B

Page B-28 G3X Installation Manual – Appendix B Revision A 190-01115-01 B.4.6 Daisy Chain Shield Termination Between Methods A and B In rare situations where more braids need to be terminated for a connector than three per ring terminal and a mixture of Methods A and B have been used, it is allowable...

Page 173 - APPENDIX C OUTLINE AND INSTALLATION DRAWINGS; G3X Installation Manual – Outline & Installation Drawings; XM

APPENDIX C OUTLINE AND INSTALLATION DRAWINGS G3X Installation Manual – Outline & Installation Drawings Page C-1 (Page C-2 blank) 190-01115-01 Revision A 7.83 198.8 6.04 153.4 2.98 75.8 3.89 98.7 2X 1.72 43.7 .004 0.1 1.09 27.7 [86.7] 3.41 .59 15.0 1.08 27.5 #6-32 CAPTIVE SCREW (4 PLCS) 5.47 139....

Page 174 - APPENDIX C OUTLINE & INSTALLATION DRAWINGS; Drawing is not to scale! Use for dimensions only.; PANEL CUTOUT; Figure C-1.2 GDU 37X Panel Cutout Drawing

APPENDIX C OUTLINE & INSTALLATION DRAWINGS G3X Installation Manual – Outline & Installation Drawings Page C-3 (Page C-4 blank) 190-01115-01 Revision A Drawing is not to scale! Use for dimensions only. 4X 4X 45° 45° 4X 4X .160 .160 4.1 4.1 R R .39 .39 TYP. TYP. 10.0 10.0 .19 .19 TYP. 4.9 1.24...

Page 175 - GMU 44 MOUNTING RACK; AIRCRAFT HOLES

APPENDIX C OUTLINE AND INSTALLATION DRAWINGS G3X Installation Manual – Outline & Installation Drawings Page C-5 (Page C-6 blank) 190-01115-01 Revision A 2.520 64.01 3.370 85.60 GMU 44 MOUNTING RACK NOTE:1. DIMENSIONS IN INCHES [mm]2. SEE SECTIONS 3 AND 4 FOR MOUNTING INSTRUCTIONS OF THE GSU 73 A...

Page 176 - GMU 44 INSTALLATION

APPENDIX C OUTLINE AND INSTALLATION DRAWINGS G3X Installation Manual – Outline & Installation Drawings Page C-7 (Page C-8 blank) 190-01115-01 Revision A 3.37 85.60 2.10 53.34 2.38 60.33 1.84 46.61 8.4 214 .3 8 AIRCRAFT MOUNTINGSURFACE NOTES:1. DIMENSIONS IN INCHES [mm] GMU 44 INSTALLATION FROM A...

Page 177 - Figure C-2.3 GMU 44 Bottom Mounted Installation

APPENDIX C OUTLINE AND INSTALLATION DRAWINGS G3X Installation Manual – Outline & Installation Drawings Page C-9 (Page C-10 blank) 190-01115-01 Revision A GMU 44 6-32 100 FLATHEAD BRASS SCREWSREQUIRED 6-32 PANHEAD BRASS SCREWS0.24 [6.1] MAX THREAD LENGTHWITHOUT CLEARANCE HOLES AIRCRAFTMOUNTING RA...

Page 180 - SHIELD OF CABLE ELECTRICALLY CONNECTED TO 16 AWG WIRE.

APPENDIX C OUTLINE AND INSTALLATION DRAWINGS G3X Installation Manual – Outline & Installation Drawings Page C-15 (Page C-16 blank) 190-01115-01 Revision A .563 -.012 +.000 NOTES: 2. MAX HEIGHT OF INCOMPLETE THREAD: 0.050 1. DIMENSIONS: INCHES 3. CABLE: M27500-22TE3V14. CABLE LENGTH TO BE 10 FEET...

Page 181 - GA 55 STUD MOUNT

APPENDIX C OUTLINE AND INSTALLATION DRAWINGS G3X Installation Manual – Outline & Installation Drawings Page C-17 (Page C-18 blank) 190-01115-01 Revision A AIRCRAFT SKIN FORWAR D FABRICATE AND INSTALL DOUBLER PLATE TORQUE 20 TO 25 in-lbs 011-01153-00 AS REQUIRED TO COMPLY WITH APPLICABLE GA 55A X...

Page 182 - GA 56 STUD MOUNT; Figure C-5.2 GA 56 Installation Drawing

APPENDIX C OUTLINE AND INSTALLATION DRAWINGS G3X Installation Manual – Outline & Installation Drawings Page C-19 (Page C-20 blank) 190-01115-01 Revision A 3.00 76.2 2X 1.2 5 31.8 5.00 127.0 FORWAR D BACKING PLATE OUTLINE .83 [21.1 ] 2.59 65.8 .60 15.2 BNC CONNECTOR FRONT VIEW 011-00134-00 ANTENN...

Page 184 - APPENDIX D INTERCONNECT DRAWING; G3X Installation Manual – Interconnect Drawings

APPENDIX D INTERCONNECT DRAWING G3X Installation Manual – Interconnect Drawings Page D-1 (Page D-2 blank) 190-01115-01 Revision A Figure D-1.1 Notes, 14V Power, and Antennas

Page 186 - APPENDIX E EXTERNAL INTERFACE DRAWING (EXAMPLE ONLY); G3X Installation Manual – External Interface Drawings

APPENDIX E EXTERNAL INTERFACE DRAWING (EXAMPLE ONLY) G3X Installation Manual – External Interface Drawings Page E-1 (Page E-2 blank) 190-01115-01 Revision A Figure E-1.1 Notes, GDU 37X RS-232 and Audio Examples

Page 188 - Figure E-1.3 Tru Trak and Trio Auto Pilot Examples

APPENDIX E EXTERNAL INTERFACE DRAWING (EXAMPLE ONLY) G3X Installation Manual – External Interface Drawings Page E-5 (Page E-6 blank) 190-01115-01 Revision A Figure E-1.3 Tru Trak and Trio Auto Pilot Examples