Furman PS-PRO II - Manuals - manualsarea.com

Page 2 - P S - P R O I I - P O W E R C O N D I T I O N E R / S E q u E N C E R; F E aT u R E S; zero ground contamination; I N T R O D u C T I O N; The Series II

P S - P R O I I - P O W E R C O N D I T I O N E R / S E q u E N C E R F E aT u R E S n SMP+ (Series Multi-Stage Protection Plus) non-sacrificial surge suppression — the most comprehensive protection available anywhere! n LiFT (Linear Filtering Technology) with zero ground contamination n Extreme vol...

Page 3 - l i n e a r; D E S C R I P T I O N

P S - P R O I I - P O W E R C O N D I T I O N E R / S E q u E N C E R l I F T ( l i n e a r f i l t e r i n g t e c h n o l o g y ) Unfortunately, traditional AC filter - conditioners have been designed for unrealistic laboratory conditions. Prior technologies, whether multiple pole filter or conven...

Page 4 - maintained; LOCAL CONTROL; NOTE: If the PS-PRO II is to be used under

P S - P R O I I - P O W E R C O N D I T I O N E R / S E q u E N C E R front panel Delay Adjust control. The Delay Adjust control, which can be set us - ing a screwdriver, controls the total delay time between Delay 2 and Delay 3. For example, if the Delay Adjust is set for 30 seconds, the De - lay 1...

Page 5 - REMOTE CONTROL

P S - P R O I I - P O W E R C O N D I T I O N E R / S E q u E N C E R local control only, and a jumper is installed on JMP1 with no switch connected to the PS-PRO II’s terminal strip, then a jumper should be connected between the REM and +12V terminals. Otherwise, turning the front panel key switch ...

Page 6 - REaR PaNEl lIgHT SWITCH:; FRONT PaNEl

P S - P R O I I - P O W E R C O N D I T I O N E R / S E q u E N C E R REaR PaNEl lIgHT SWITCH: All Series II units feature a rear rack BNC socket which will accept any 12 VAC (0.5A) gooseneck lamp as - sembly, (such as the Furman GN-LED or GN-I). Simply slide the BNC plug over the socket and rotate ...

Page 7 - installed at the remote end to indicate that the; REaR PaNEl

P S - P R O I I - P O W E R C O N D I T I O N E R / S E q u E N C E R BNC Connector for rear light (models GN-I or GN-LED) POWER STaTuS (DElaY) lEDs: One green LED is provided for each of the three delay stages. Each LED lights when power is applied to its corresponding duplex outlet on the rear pan...

Page 8 - MAINTAINED MODE; There are 3 maintained modes of operation:; MOMENTARy MODE

P S - P R O I I - P O W E R C O N D I T I O N E R / S E q u E N C E R MAINTAINED MODE There are 3 maintained modes of operation: REM to +12V = OFF (jumper plug installed on JMP1, MAINT ON)The connection of the REM terminal to the +12V terminal initiates an OFF sequence. Disconnecting initiates an ON...

Page 9 - MULTIPLE UNITS

P S - P R O I I - P O W E R C O N D I T I O N E R / S E q u E N C E R contact switch, the RS-1 is not an appropriate remote switch for the PS-PRO II when it is in momentary mode. The Furman RS-2 is the proper choice. Please contact Furman for RS-2 wiring diagrams. MULTIPLE UNITS you can use more tha...

Page 10 - FLASHING DELAy 1 INDICATOR

P S - P R O I I - P O W E R C O N D I T I O N E R / S E q u E N C E R FLASHING DELAy 1 INDICATOR The DELAy 1 LED on a PS-PRO II flashes to indicate that a remote switch is off or not connected. In Maintained Mode (JMP1, MAINT ON’s jumper plug is installed), this will only occur when the REM terminal...

Page 11 - S E R V I C E

P S - P R O I I - P O W E R C O N D I T I O N E R / S E q u E N C E R 10 liability or otherwise. Under no circumstances, whether based on this Limited Warranty or otherwise, shall Manufacturer be liable for in - cidental, special, or consequential damages. Manufacturer’s employees or representatives...