Friedrich P/N9359944072-01 - Manuals

En-5 PREPARATION CAUTION! ● Take care to prevent infants fromaccidentally swallowing batteries. ● When not using the remote control unitfor an extended period, remove thebatteries to avoid possible leakage anddamage to the unit. ● If leaking battery fluid comes in contactwith your skin, eyes, or mou...

En-6 Example: When set to COOL Example: When set to 88 °F Example: When set to AUTO To Select Mode Operation 1 Press the START/STOP button. The indoor unit’s OPERATION indicator lamp (red) will light.The air conditioner will start operating. 2 Press the MASTER CONTROL button to select the de-sired m...

En-7 OPERATION Instructions relating to heating (*) are applicable only to “HEAT & COOL MODEL” (Reverse Cycle). * During Heating mode: Set the thermostat to a temperature set-ting that is higher than the current roomtemperature. The Heating mode will notoperate if the thermostat is set lower tha...

En-8 To Use the ON timer or OFF timer 1 Press the START/STOP button(if the unit is already operating, proceed to step 2). The indoor unit’s OPERATION indicator lamp (red) will light. 2 Press the TIMER button to select the OFF timer or ONtimer operation. Each time the button is pressed the timer func...

En-9 SLEEP TIMER OPERATION To Use the SLEEP timer While the air conditioner is operating or stopped, press theSLEEP button. Both the indoor unit’s OPERATION indicator lamp (red) and the TIMER indicatorlamp (green) will light. To Change the Timer Settings Press the SLEEP button once again and set the...

En-10 ADJUSTING THE DIRECTION OF AIR CIRCULATION Instructions relating to heating (*) are applicable only to “HEAT & COOL MODEL” (Reverse Cycle). Vertical (up-down) direction of airflow is adjusted by pressing the remote control unit’s AIR FLOW DIRECTION VERTICAL SETbutton. Horizontal (right-lef...

En-11 SWING OPERATION Begin air conditioner operation before performing this procedure. To select Vertical airflow SWING Operation Press the AIR FLOW DIRECTION VERTICAL SWING button. The SWING indicator lamp (VERTICAL SWING) (orange) will light.In this mode, the UP/DOWN air direction flaps will swin...

En-12 ● Before cleaning the air conditioner, be sure to turn it off and disconnect the power supply cord. ● Be sure the intake grille is installed securely. ● When removing and replacing the air filters, be sure not to touch the heat exchanger, as per-sonal injury may result. CLEANING AND CARE CAUTI...

En-13 When two or more air conditioners are installed in a room and the remote controlunit is operating an air conditioner other than the one you wish to set, change thesignal code of the remote control unit to operate only the air conditioner you wishto set (four selections possible).When two or mo...

En-14 TROUBLESHOOTING Instructions relating to heating (*) are applicable only to “HEAT & COOL MODEL” (Reverse Cycle). In the event of a malfunction (burning smell, etc.), immediately stop operation, disconnect thepower supply plug, and consult authorized service personnel.Merely turning off the...

En-15 TROUBLESHOOTING Instructions relating to heating (*) are applicable only to “HEAT & COOL MODEL” (Reverse Cycle). Symptom Doesn’t operate at all: Poor Cooling (or *Heating)performance: The unit operates differ-ently from the remote con-trol unit’s setting: Signal is not received afterreplac...

En-16 OPERATING TIPS ● Should the power supply to the air conditioner be inter-rupted by a power failure, the air conditioner will restartautomatically in the previously selected mode once thepower is restored. ● Should a power failure occur during TIMER operation, thetimer will be reset and the uni...

Friedrich Air Conditioning Co. 4200 N. Pan Am San Antonio, Texas 78218 USA Tel. (210) 357-4400 Fax (210) 357-4490 Visit us at www. friedrich. com 9359944072-01_OM_es.p65 1/21/10, 1:56 PM 19