Friedrich MR12C1H - Manuals

Notices for use Anti-cool wind function: In "Heat" mode, under the following three kinds of state, if indoor heat exchanger doesn't 2 mins): 1. Heating starts. 2.After Auto Defrost finished. 3.Heating under the low temperature. The operating temperature range (outdoor temperature) for coolin...

MODE (AUTO/COOL/DRY/FAN/HEAT). setting. : Press to decrease temperature setting. FAN Press it set swing angle. TIMER ON TIMER OFF CLOCK TEMP TURBO SLEEPLIGHT Press it to set auto-on timer. Press it to set auto-off timer Press it set clock. 1 6 7 5 3 2 4 11 10 14 9 12 13 15 Operation of Remote Contro...

This area will show the set tempe-rature. In SAVE mode,"SE" will be displayed. During defrosting opera-tion, “H1” will be displayed. DIGITAL display: LOCK icon: is displayed by pressing "+" and “-” buttons simultaneously. Press them again to clear the display. LIGHT icon: is displaye...

is displayed when pressing the again to clear the display. Press FAN button to select thedesired fan speed setting (AUTO- Low-Med-High).Your selection willbe displayed in the LCD windows,except the AUTO fan speed. FAN SPEED display: is displayed when pressing the to clear the display. Operation of R...

Press ing CLOCK button, blink s . Within 5 seconds , pressing + or - button adjusts the present time. Holding down either button above 2 seconds increases or decreases the CLOCK : time by 1 minute every 0.5 second and then by 10 minutes every 0.5 second. During blinking after setting, press CLOCK bu...

13 TEMP: ambient temperature, 5s later or within 5s, it receives other remote control signal that will return to display the setting temperature. if the users haven't set up the temperature displaying status,that will display the setting temperature.(This function is not applicable for some models)....

★ ● ● ●● ● 1.Remove the battery cover plate from the rear of the remote controller. (As shown in the figure) 2.Take out the old batteries. 3.Insert two new AAA1.5V dry batteries, and pay attention to the polarity. 4. Reinstall the battery cover plate. When replacing the batteries, do not use old or ...

If the wireless remote control is lost or broken, please use the manual switch Auto mode, but the temperature and fan pressing this button. In which case,the diss-player indicator light will be on if the AC receives be off if the AC receives this signal. ● ● display on the remote controller screen b...

℃ ● ● ● ● ● ℃ ② Clean the air filter ③ ① ( a ) ( b ) Caution Turn power off and pull out the power plug before cleaning air conditioner, or it may cause electric shock. Never sprinkle water on the indoor unit and the outdoor unit for cleaning because it can cause an electric shock. Volatile liquid (...

T h e s o u n d o f w a t e r f l o wd u r i n g o p e r a t i o n . ● Tu r n u n i t o n . ● R a i s e / L o w e r t e m p e r a t u r e s e t t i n g . ● U n i t w i l l r e s u m e n o r m a l o p e r a t i o n o n c e p o w e r h a s b e e n r e s t o r e d . ● C l e a n a i r f i l t e r. ● C l...

C a u s e Immediately stop all operations and plug out, contact the dealer in following situations occur. There is harsh sound during operation . The terrible odors emitted during operation . Water is leaking in the room . Air switch or protection switch often breaks . There is an abnormal heat in p...

S e r v i c e & A s s i s t a n c e Tr o u b l e s h o o t i n g " s e c t i o n a n d s t i l l n e e d h e l p , h e r e i s a l i s t o f a v a i l a b l e s e r v i c e s : 1 2 3 15

1. 2. Select a position where the condensing water can be easily drained out, and the place is easily connected for outdoor unit. 4. Can select the place where is strong enough to withstand the full weight and vibration of the unit. And will not increase the noise. 5. 6. 7. 8. Make sure that the ind...

Safety Requirements For Electric Appliances Note: Make sure that the Live wire or Zero line as well as the earth wire in the family power socket can not be wrong connected, there should be reliable and no short circuit in the diagram. wrong connection may cause fire. ● ● 1. The power supply should b...

Space to the wall e v o b A e v o b A Installation dimension diagram Space to the ceiling Space to the wall Space to the wall Air outlet side Space to the floor Above Above Above Above Above The dimensions of the space necessary for correct installation of the appliance including the minimum permiss...

Install indoor unit Ø 5 5 Install the rear panel 1.Always mount the rear panel horizontally. Due to the water tray of indoor unit has been adopted the both-way drainage design, the outlet of water tray should be adjusted slightly down when installing, that is taking the outlet of the water tray as t...

● ● ● After tighten the screw, slight pull the wire and confirm whether is it firm or not. ● ● The cover plate must be fixed, and tighten the connection wire, if it is poor installed, that Install indoor unit NOTE: When connecting the electric wire if the wire length is not enough, please contact wi...

Ø Condensate drainage of outdoor unit (no for cooling only) The condensate and defrosting water formd during heating in the outdoor unit can be properly discharged by drainage pipe . Installation method:set the drain connection in 25 hole of the chassis has been installed and then connect drainage p...

1. (2) Electric wiring must be connected correctly and securely. (3) Cut-off valves of the connection pipes should be opened. (4) 2. the operation. (2) Check after installation Items to be checked Possible malfunction Has it been fixed firmly? The unit may drop, shake or emit noise. Have you done th...