Friedrich 920-087-09 - Manuals

5 PTAC Installation Recommendations PTAC units should be installed no closer than 12" apart when two units are side by side. If three or more PTAC units are to operate next to one another allow a minimum of 36" between units. Also, a vertical clearance of 60" should be maintained between...

6 Wall Sleeve Installation Instructions (PDXWS) NOTE: Insure that the unit is only installed in a wall structurally adequate to support the unit including the sleeve, chassis and accessories. If the sleeve projects more than 8" into the room, a subbase or other means of support MUST be used. Ple...

7 NOTE: Follow all wall system manufacturer installation instructions. For sunrooms and modular buildings, adhere to their installation instructions for supporting and sealing sleeve to their frames. All wall and window/wall installations must provide for proper drainage. In applications where the d...

8 Figure 9 Dimensions FRP007 NOTE: The Wall Sleeve must behorizontally level (side-to-side)and pitched 1/4 bubble to theoutside when installed in anopening.The mounting hole locationshould be approximately 2-4”from the top and bottom of thesleeve. MOUNTING HOLES PLASTIC ANCHORS WOOD SCREW ALTERNATEF...

9 FRP010 NOTE: Construct wall opening to comply with all applicable building codes. MAIN STUDS JACK STUDS LINTEL MOUNTINGSCREW HOLES NO HOLES IN BOTTOM OF WALLSLEEVE UNLESS DRAIN KIT IS USED MAIN STUDS JACK STUDS 5. Drill two 3/16" holes through each side of the sleeve approximately 4" from ...

10 FRP011 DRAIN TUBE SIDE VIEW FRONT VIEW WALL SLEEVE OPTIONAL AREA PREFERRED AREA-NO FOAM INSULATION IF THE DRAIN MUST BELOCATED IN THE OPTIONALAREA, THE FOAM INSULATIONMUST BE CUT AWAY ANDREMOVED TO ALLOW ACCESSTO THE DRAIN. NUT MOUNTINGPLATE GASKET SCREW 3" Figure 11 Drain Kit Location and In...

11 FRP012 FOAMGASKET OVERFLOW SLOTS DETAIL B DETAIL A COVERPLATE FOAMGASKET SCREWS ½” O.D. TUBE MOUNTINGPLATE NUT External Drain (for new construction or unit replacement) When using an external drain system, the condensate is removed through either of two drain holes on the back of the wall sleeve....

12 PXGA Standard Grille Installation Instructions 1. Remove the center support and weatherboard if still installed in the sleeve. 2. Insert six plastic grommets into the grille openings from the outside of the grille as shown in Figure 13. 3. Insert two #8 x ⅜" sheet metal screws (provided) in t...

13 W ARNING 15/20A LCDI Device 30A LCDI Device TEST BEFORE EACH USE 1. PRESS RESET BUTT ON 2. PLUG LCDI INT O POWER RECEPT ACLE 3. PRESS TEST BUTT ON, RESET BUTT ON SHOULD POP UP 4. PRESS TEST BUTT ON, FOR USE DO NOT USE IF ABOVE TEST F AILS WHEN GREEN LIGHT IS ON IT IS WORKING PROPERL Y RESET TEST ...

14 TABLE 2 Model Heater kW Power Cord Kit Voltage Amperage Receptacle PDE07K 0.0 PXPC23000 230/208 15 NEMA 6-15r PDE/PDH07K 2.0 PXPC23015 230/208 15 NEMA 6-15r 3.0 STD 230/208 20 NEMA 6-20r PDE09K 0.0 PXPC23000 230/208 15 NEMA 6-15r PDE/PDH09K 2.0 PXPC23015 230/208 15 NEMA 6-15r 3.0 STD 230/208 20 N...

16 Chassis Install Preparation Check to be sure the wall sleeve, extension (if used), grille, and drain kit are installed properly before chassis installation. 1. Remove the weatherboard and center support from the sleeve (if still in place). Be sure an outdoor grille is attached. NOTE: Use a wall s...

17 FRP020 SHIPPINGTAPE Figure 20 Shipping Tape Location FRP021 REMOVE SHIPPINGSCREW IF PRESENT Figure 21 Shipping Screw Location Figure 22 Removing Front Panel CAUTION Unit Damage Hazard Failure to follow this caution may result in equipment damageor improper operation. Failure to remove shipping ta...

18 1. Lift unit level and slide unit into wall sleeve until from seal rests firmly against front of wall sleeve. 2. Locate the four supplied chassis mounting screws. Insert the screws through the chassis mounting flange holes that are aligned with the speed nuts in the wall sleeve. Tighten all four ...

19 How To Connect IMPORTANT: Please read following electrical safety data carefully. 1. Remove front panel. See Figure 22. 2. Remove junction box. • Remove junction box cover by removing three screws from front. Remove junction box by taking out top, rear and side screws. See Figure 24. WARNING Elec...

20 Friedrich PTAC Digital Control and Unit Features The new Friedrich digital PTAC has state of the art features to improve guest comfort, indoor air quality and conserve energy. Through the use of specifically designed control software for the PTAC industry Friedrich has accomplished what other Man...

22 System Configuration Fresh Air Vent Control The vent control lever is located on the left side of the unit, behind the front panel. NOTE: The vent door shipping hardware must be removed before using the vent control lever. See page 17, Figure 21, (Remove Shipping Screw from Vent Door if present)....

23 The adjustable control dip switches are located at the lower left hand portion of the digital Smart Center. The inputs are only visible and accessible with the front cover removed from the PTAC. Digital Control User Input Configuration Switch Description Function Factory Setting Option 1 Emergenc...

24 FRP030 High Med Low Fan Cool Heat Fan Speed Mode Temperature Power °F vs. °C Display The unit is factory configured to display all temperatures in degrees Fahrenheit (° F). To switch to degrees Celsius press the ‘Fan Only’ and ‘Low Fan’ buttons simultaneously for three seconds. The display will s...

26 Desk Control Terminals The Friedrich PD model PTAC has built-in provisions for connection to an external switch to control power to the unit. The switch can be a central desk control system or even a normally open door switch.For desk control operation connect one side of the switch to the D1 ter...

27 q Inspect and ensure that all components and accessories have been installed properly and that they have not been damaged during the installation process. q Check the condensate water drain(s) to ensure they are adequate for the removal of condensate water, and that they meet the approval of the ...

28 Basic Troubleshooting COMPLAINT CAUSE SOLUTION Unit does not operate. ● Unit turned off. ● Turn unit on ● Thermostat is satisfied. ● Raise/Lower temperature setting. ● LCDI power cord is unplugged. ● Plug into a properly grounded 3 prong recep- tacle. See "Electrical Rating Tables" on pag...

30 New Construction Accessories PDXWS PDXWSEXT WALL SLEEVE Galvanized zinc coated steel is prepared in an 11-step process, then powder coated with a polyester finish and cured in an oven for exceptional durability. The wall sleeve is insulated for sound absorption and thermal ef- ficiency, 16" H...

31 New Construction Accessories PXCJA CONDUIT KIT WITH JUNCTION BOX Hard wire conduit kit with junction box for 208/230V and 265V units (subbase not required). Kit includes a means of quick disconnect for easy removal of the chassis. *Required for 265V installations. PXFTA REPLACEMENT FILTER PACK Th...

32 Friedrich Air Conditioning Company 10001 Reunion Place, Suite 500 San Antonio, TX 78216 210.357.4400 www.friedrich.com ROOM AIR CONDITIONERS LIMITED WARRANTY ANY PART: If any part supplied by FRIEDRICH fails because of a defect in workmanship or material within twelve months from date of original...