Ford 2007 Taurus- Manuals

Please read the section Supplemental restraint system (SRS) in the Seating and Safety Restraints chapter. Failure to follow the specific warnings and instructions could result in personal injury. Front seat mounted rear-facing child or infant seats should NEVER be placed in front of an active passen...

Cell phone use The use of Mobile Communications Equipment has become increasinglyimportant in the conduct of business and personal affairs. However,drivers must not compromise their own or others’ safety when usingsuch equipment. Mobile Communications can enhance personal safetyand security when app...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat Child Seat InstallationWarning Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Brake Fluid -...

WARNING LIGHTS AND CHIMES Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause expensive repairs. A warning light mayilluminate when a problem exists with one of your vehicle’s functions.Many lights will illuminate when you start your vehicle to make ...

Brake system warning light: To confirm the brake system warninglight is functional, it willmomentarily illuminate when theignition is turned to the ON positionwhen the engine is not running, or in a position between ON and START,or by applying the parking brake when the ignition is turned to the ONp...

Engine oil pressure: Illuminates when the oil pressure falls below thenormal range, refer to Engine oil in the Maintenance and Specifications chapter. Traction Control 娂 active (if equipped): Flashes when the Traction Control 娂 is active. If the light remains on a malfunction hasbeen detected; have ...

GAUGES Speedometer: Indicates the current vehicle speed. Engine coolant temperaturegauge: Indicates engine coolant temperature. At normal operatingtemperature, the needle will be inthe normal range (between “H” and“C”). If it enters the red section, the engine is overheating. Stopthe vehicle as soon...

AUDIO SYSTEMS AM/FM stereo cassette/MACH 姞 AUDIO SYSTEM with AM/FM stereo cassette (if equipped) 1. Tape: Insert the cassette with the opening to the right. If a tape isalready inserted into the system,press TAPE to begin tape play. 2. Clock: To set the hour, press and hold the H control. When thede...

6. Scan: Press to hear a brief sampling of all listenable radiostations or CD tracks. Press again tostop. 7. CD: Press to play a CD. Press again to toggle between single CDmode and CD Changer mode (ifequipped). 8. Shuffle: Press to play CD tracks in random order. 9. COMP (compression): Press to brin...

5. Line up the CD with the grooveof the disc holder. Ensure that thelabel on the CD faces downwards. 6. Press the disc holder until it lockssecurely into the magazine. Ensure that the disc holder isevenly inserted and at the samelevel as the magazine (A). The unitwill not operate if the disc holder ...

• Remove loose labels before inserting tapes. • Allow tapes which have been subjected to extreme heat, humidity orcold to reach a moderate temperature before playing. • Clean the cassette player head with a cassette cleaning cartridge after10–12 hours of play to maintain good sound/operation. Don’t:...

MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED) 1. Temperature selection: Controls the temperature of theairflow in the vehicle. 2. Passenger airbag indicator light: Refer to Front passenger sensing system in the Seating and Safety Restraints chapter. 3. Air flow selections: Controls the dir...

Operating tips • To reduce fog build up on the windshield during humid weather, placethe air flow selector in the position. • To reduce humidity buildup within the cabin, do not drive with theselector in the OFF or MAX A/C position when outside temperature isbelow 40°F (3°C). • To improve A/C cool d...

AUTOMATIC TEMPERATURE CONTROL SYSTEM (IF EQUIPPED) 1. OFF: Outside air is shut out and the climate control system is turnedoff. 2. A/C: Press to activate/deactivate air conditioning. Use with the recirculated air to improve cooling performance and efficiency. Engagesautomatically in the AUTO, F (def...

6. AUTO: Press to engage full automatic operation, and select thedesired temperature using thetemperature control. The system will automatically determine fan speed,airflow location, A/C on or off, and outside or recirculated air, to heat orcool the vehicle to reach the desired temperature. 7. Fan S...

The defroster turns off automatically after 10 minutes or when theignition is turned to the OFF position. To manually turn off the defrosterbefore 10 minutes have passed, push the control again. Do not use razor blades or other sharp objects to clean the insideof the rear window or to remove decals ...

HEADLAMP CONTROL Turns the lamps off. Turns on the parking lamps, instrument panel lamps, licenseplate lamps and tail lamps. Turns the headlamps on. Autolamp control (if equipped) The autolamp system provides lightsensitive automatic on-off control ofthe exterior lights normallycontrolled by the hea...

Flash to pass Pull toward you slightly to activateand release to deactivate. Daytime running lamps (DRL) (if equipped) Turns the headlamps on with a reduced output. To activate: • the ignition must be in the ON position, • the headlamp control is in the OFF or parking lamp position and • the parking...

Replacing the interior bulbs Check the operation of all bulbs frequently. Replacing exterior bulbs Check the operation of all the bulbs frequently. Replacing headlamp bulbs To remove the headlamp bulb: 1. Make sure headlamp switch is inOFF position and open the hood. 2. Remove the bolt (1) from theh...

5. Disconnect the electricalconnector from the bulb by pullingrearward. 6. Remove the bulb retaining ring byrotating it counterclockwise. 7. Remove the old bulb from thelamp assembly by pulling it straightout of the lamp assembly. To install the new bulb: Handle a halogen headlamp bulb carefully and...

MULTI-FUNCTION LEVER Windshield wiper: Rotate the end of the control away from you toincrease the speed of the wipers;rotate towards you to decrease thespeed of the wipers. Windshield washer: Push the end of the stalk: • briefly: causes a single swipe ofthe wipers without washer fluid. • a quick pus...

ILLUMINATED VISOR MIRROR (IF EQUIPPED) Lift the mirror cover to turn on thevisor mirror lamp. CENTER CONSOLE Your vehicle may be equipped with a variety of console features. Theseinclude: • Utility compartment • Bin mat (snap-in) • Cupholders (front and rear) • Coin holder slots • Compact disc chang...

Do not use the power point for operating the cigarette lighter element (ifequipped). To prevent the fuse from being blown, do not use the power point(s)over the vehicle capacity of 12 VDC/180W. To prevent the battery from being discharged, do not use the powerpoint longer than necessary when the eng...

EXTERIOR MIRRORS Power side view mirrors To adjust your mirrors: 1. Select L to adjust the left mirror or R to adjust the right mirror. 2. Move the control in the directionyou wish to tilt the mirror. 3. Return to the center position todisable the adjust function. Heated outside mirrors (if equipped...

Setting speed control The controls for using your speedcontrol are located on the steeringwheel for your convenience. 1. Press the ON control and releaseit. 2. Accelerate to the desired speed. 3. Press the SET ACC control andrelease it. 4. Take your foot off the acceleratorpedal. 5. The CRUISE indic...

• Depress the brake pedal until thedesired vehicle speed is reached,press the SET ACC control. Turning off speed control There are two ways to turn off the speed control: • Depress the brake pedal. This willnot erase your vehicle’spreviously set speed. • Press the speed control OFFcontrol. Note: Whe...

Before operating the moonroof you should verify that it is free ofobstructions and ensure that children and/or pets are not in the proximity of moon roof opening. Do not let children play with the moon roof or leave childrenunattended in the vehicle. They may seriously hurt themselves. HOMELINK 姞 WI...

Note: If the indicator light blinks rapidly for two seconds and then turns to a continuous red, proceed with Steps 6 through 8 to completeprogramming of a rolling code equipped device. 6. At the garage door opener receiver (motor-head unit) in the garage,locate the “learn” or “smart” button (usually...

Operating the HomeLink 姞 Wireless Control System To operate, simply press and releasethe appropriate HomeLink 威 button. Activation will now occur for thetrained product (garage door, gateoperator, security system, entrydoor lock, or home or office lightingetc.). For convenience, thehand-held transmi...

MESSAGE CENTER With the ignition in the ON position,the message center, located on yourinstrument cluster, displaysimportant vehicle information through a constant monitor ofvehicle systems. You may select display features on the message center for a display of status precededby a brief indicator ch...

Most geographic areas (zones) have a magnetic north compass point thatvaries slightly from the northerly direction on maps. This variation is fourdegrees between adjacent zones and will become noticeable as thevehicle crosses multiple zones. A correct zone setting will eliminate thiserror. Refer to ...

System warnings System warnings alert you to possible problems or malfunctions in yourvehicle’s operating systems. In the event of a multiple warning situation, the message center will cyclethe display to show all warnings by displaying each one for several seconds. The message center will display t...

POSITIVE RETENTION FLOOR MAT Do not install additional floor mats on top of the factory installedfloor mats as they may interfere with the accelerator or the brake pedals. Position the driver floor mat so thatthe eyelet is over the pointed end ofthe retention post and rotateforward to lock in. Make ...

KEYS The key operates all locks on your vehicle. In case of loss, replacementkeys are available from your dealer. You should always carry a second key with you in a safe place in caseyou require it in an emergency. Refer to the SecuriLock 娂 passive anti-theft system section in this chapter for more ...

1. Turn the ignition to the 4 (ON)position, then press the power doorUNLOCK control 3 times. 2. Turn the ignition to the 3 (OFF)position, then press the power doorUNLOCK control 3 times. 3. Turn the ignition to the 4 (ON)position. The horn will chirp one time as confirmation that theprogramming mode...

INTERIOR LUGGAGE COMPARTMENT RELEASE Your vehicle is equipped with a mechanical interior luggage compartmentrelease handle that provides a means of escape for children and adults inthe event they become locked inside the luggage compartment.Adults are advised to familiarize themselves with the opera...

To replace the battery: 1. Twist a thin coin between the twohalves of the remote entrytransmitter near the key ring. DONOT TAKE THE RUBBER COVERAND CIRCUIT BOARD OFF THEFRONT HOUSING OF THEREMOTE ENTRY TRANSMITTER. 2. Do not wipe off any grease on thebattery terminals on the backsurface of the circu...

2. Press and release the 1 • 2 within five seconds of completing Step 1. 3. Press and hold the 1 • 2 for two seconds to erase the customer programmed codes. All personal codes are now erased and only the factory set 5–digit codewill work. Note: To exit programming mode, either wait 5 seconds after p...

engine. If a problem occurs, turn the ignition off, remove all objects onthe key chain away from the coded key and restart the engine. Anti-theft indicator The anti-theft indicator is located in the instrument cluster. • When the ignition is in the 2 (LOCK) position, the indicator will flashonce eve...

Programming spare keys You can program your own coded keys to your vehicle. Please read andunderstand the entire procedure before you begin. Tips: • A maximum of eight keys can be coded to your vehicle. • Only use Securilock 娂 keys. • You must have two previously programmed coded keys (keys thatalre...

Disarming the system You can disarm the system by any of the following actions: • Unlock the doors by pressing the control on your remote entry transmitter. • Unlock the doors by using the keyless entry pad. • Unlock the doors with a key. Turn the key full travel (toward the frontof the vehicle) to ...

SEATING Notes: Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in the event of a collision. Do not pile cargo higher than the seatbacks to reduce the risk ofinjury in a collision or sudden stop. Before returning the seatback to...

To lower the head restraint: • Push the release control. • Push down on the head restraint. Using the manual lumbar support (if equipped) The lumbar control is located on thefront of the seat cushion. Turn to adjust lumbar support. Adjusting the front manual seat (if equipped) Never adjust the drive...

Pull lever up to adjust seatback. Before returning theseatback to its original position, make sure that cargo orany objects are not trappedbehind the seatback. Afterreturning the seatback to itsoriginal position, pull on theseatback to ensure that it has fullylatched. An unlatched seat maybecome dan...

REAR SEATS 2nd seat/split-folding rear seat (if equipped) Pull the loop forward to release theseatback and then fold the seatbackdown. When raising the seatback(s), make sure you hear the seat latch intoplace. Make sure that the safety belt for the rear center passenger is properlyrouted over the re...

• A series of five beeps will be heard. The tone pattern will repeatperiodically until the problem and warning light are repaired. If any of these things happen, even intermittently, have the PersonalSafety System 娂 serviced at an authorized dealer immediately. Unless serviced, the system may not fu...

Always transport children 12 years old and under in the backseat and always properly use appropriate child restraints. Combination lap and shoulder belts 1. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) until you hear a snap and feelit lat...

Vehicle sensitive mode This is the normal retractor mode, which allows free shoulder belt lengthadjustment to your movements and locking in response to vehiclemovement. For example, if the driver brakes suddenly or turns a cornersharply, or the vehicle receives an impact of approximately 5 mph (8km/...

How to disengage the automatic locking mode Ford Motor Company recommends that all safety belt assembliesand attaching hardware should be inspected by an authorized dealer after any collision. Safety belt assemblies not in use during acollision should also be inspected and replaced if either damage ...

activated, the safety belt pretensioner for that seating position will beactivated if the safety belt is properly buckled. The driver and front outboard passenger safety belt system (includingretractors, buckles and height adjusters) must be replaced if the vehicleis involved in a collision that res...

Position the safety belt height adjusters so that the belt restsacross the middle of your shoulder. Failure to adjust the safety belt properly could reduce the effectiveness of the seat belt andincrease the risk of injury in a collision. Lap beltsAdjusting the center front lap belt The center front ...

Do not use extensions to change the fit of the shoulder beltacross the torso. Safety belt maintenance Inspect the safety belt systems periodically to make sure they workproperly and are not damaged. Inspect the safety belts to make surethere are no nicks, tears or cuts. Replace if necessary. All saf...

The following are reasons most often given for not wearing safety belts(All statistics based on U.S. data): Reasons given... Consider... “Crashes are rare events” 36700 crashes occur every day. The more we drive, the more we areexposed to “rare” events, even forgood drivers. 1 in 4 of us will be ser...

Reasons given... Consider... “I have an airbag” Airbags offer greater protection whenused with safety belts. Frontal airbagsare not designed to inflate in rear andside crashes or rollovers. “I’d rather be thrown clear” Not a good idea. People who are ejected are 40 times more likelyto DIE. Safety be...

AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) The airbag supplemental restraint system (SRS) is designed to work inconjunction with the safety belts to help protect the driver and frontoutboard passenger from certain upper body injuries. The term“supplemental restraint” means the airbags are intended a...

Important supplemental restraint system precautions Airbags DO NOT inflate slowly orgently and the risk of injury from adeploying airbag is greatest close tothe trim covering the airbag module. All occupants of the vehicle, including the driver, should alwaysproperly wear their safety belts, even wh...

Do not attempt to service, repair, or modify the airbagsupplemental restraint system (SRS) or its fuses. See your authorized dealer. The front passenger airbag is not designed to offer protection toan occupant in the center front seating position. Modifying or adding equipment to the front end of th...

How do the airbag supplemental restraints work? The airbags inflate and deflaterapidly upon activation. After airbagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt propellant. This mayconsist of cornstarch, talcumpowder (to lubricate the bag) orsodium compounds (e.g...

The front passenger sensing system works with sensors that are part ofthe front passenger’s seat and safety belt. The sensors are designed todetect the presence of a properly seated occupant and determine if thefront passenger’s frontal airbag should be enabled (may inflate) ordisabled (will not inf...

• Objects placed on the occupant’s lap • Cargo interference with the seat • Other passengers pushing or pulling on the seat • Rear passenger feet and knees resting or pushing on the seat The conditions listed above may cause the weight of a properly seatedoccupant to be incorrectly interpreted by th...

• If the airbag readiness lamp remains illuminated, this may or may/notbe a problem due to the front passenger sensing system. DO NOT attempt to repair or service the system; take your vehicleimmediately to an authorized dealer. The front passenger airbag is not designed to offer protection toan occ...

The side airbags are fitted on the outboard side of the seatbacks of thefront seats. In certain lateral collisions, the airbag on the side affected bythe collision will be inflated, even if the respective seat is not occupied.The airbag was designed to inflate between the door panel and occupantto f...

Important child restraint precautions You are required by law to use safety restraints for children in the U.S.and Canada. If small children (generally children who are four years oldor younger and who weigh 40 lb. [18 kg] or less) ride in your vehicle, youmust put them in safety seats made especial...

Never use pillows, books, or towels to boost a child. They canslide around and increase the likelihood of injury or death in a collision. SAFETY SEATS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of thechild. Carefully follow all o...

Installing child safety seats in the center lap belt seating position 1. Lengthen the lap belt. To lengthen the belt, hold the tongue so that itsbottom is perpendicular to the direction of webbing while sliding thetongue up the webbing. 2. Place the child safety seat in the center seating position. ...

Attaching safety seats with LATCH (Lower Anchors and Tethers forChildren) attachments for child seat anchors Some child safety seats have two rigid or webbing mounted attachmentsthat connect to two anchors at certain seating positions in your vehicle.This type of child seat eliminates the need to us...

INFORMATION ABOUT UNIFORM TIRE QUALITY GRADING New vehicles are fitted with tiresthat have a rating on them calledTire Quality Grades. The Qualitygrades can be found whereapplicable on the tire sidewallbetween tread shoulder andmaximum section width. Forexample: • Treadwear 200 Traction AA Temperatu...

The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning or peak traction characteristics. Temperature A B C The temperature grades are A (the highest), B and C, representing thetire’s resistance to the gene...

gauges may be inaccurate. Ford Motor Company recommends the use ofa digital or dial-type tire pressure gauge rather than a stick-type tirepressure gauge. Use the recommended cold inflation pressure for optimum tireperformance and wear. Under-inflation or over-inflation may causeuneven treadwear patt...

To check the pressure in your tire(s): 1. Make sure the tires are cool, meaning they are not hot from drivingeven a mile. Note: If you have to drive a distance to get air for your tire(s), check and record the tire pressure first and add the appropriate air pressurewhen you get to the pump. It is no...

Improper or inadequate vehicle maintenance can cause tires to wearabnormally. Inspect all your tires, including the spare, frequently, andreplace them if one or more of the following conditions exist: Tire wear When the tread is worn down to1/16th of an inch (2 mm), tires mustbe replaced to help pre...

Do not spin the wheels at over 35 mph (56 km/h). The tires mayfail and injure a passenger or bystander. Highway hazards No matter how carefully you drive there’s always the possibility that youmay eventually have a flat tire on the highway. Drive slowly to theclosest safe area out of traffic. This m...

• Front Wheel Drive (FWD)vehicles (front tires at top ofdiagram) Sometimes irregular tire wear can be corrected by rotating the tires. Note: If your tires show uneven wear ask an authorized dealer to check for and correct any wheel misalignment, tire imbalance or mechanicalproblem involved before ti...

Information on “P” type tires P215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (Note thatthe tire size, load index and speedrating for your vehicle may bedifferent from this example.) 1. P: Indicates a tire, designated by the Tir...

12. Treadwear, Traction and Temperature Grades • Treadwear: The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on aspecified government test course. For example, a tire graded 150would wear one and one-half (1 1 ⁄ 2 ) times as well ...

Additional information contained on the tire sidewall for “LT” typetires “LT” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: 1. LT: Indicates a tire, designated by the Tire and Rim Association(T&RA), that is intended for serviceon ...

Information on “T” type tires “T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: T145/80D16 is an example of a tiresize. Note: The temporary tire size for your vehicle may be different fromthis example. 1. T: Indicates a type of tire, ...

SNOW TIRES AND CHAINS Snow tires must be the same size and grade as the tires youcurrently have on your vehicle. The tires on your vehicle have all weather treads to provide traction inrain and snow. However, in some climates, you may need to use snowtires and chains. If you need to use snow tires a...

Vehicle Curb Weight – is the weight of your new vehicle when you picked it up from your authorized dealer plus any aftermarketequipment. Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Label on the B-...

Example only: Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue loador king pin weight is also part of cargo weight. GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehi...

GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Labellocated on the B-Pillar or the edge of the driver’s door. The totalload on each axle must never exceed its GAWR....

Exceeding any vehicle weight rating limitation could result inserious damage to the vehicle and/or personal injury. Steps for determining the correct load limit: 1. Locate the statement “The combined weight of occupants and cargoshould never exceed XXX kg or XXX lbs.” on your vehicle’s placard. 2. D...

transport the cement to your home? If you and your friend each weigh220 lb. (99 kg), the calculation would be: 1400 – (2 x 220) – (12 x100) = 1400 – 440 – 1200 = – 240 lb. No, you do not have enoughcargo capacity to carry that much weight. In metric units, thecalculation would be: 635 kg — (2 x 99 k...

Trailer lamps Trailer lamps are required on most towed vehicles. Make sure all runninglights, brake lights, turn signals and hazard lights are working. See yourauthorized dealer or trailer rental agency for proper instructions andequipment for hooking up trailer lamps. Driving while you tow When tow...

RECREATIONAL TOWING Follow these guidelines for your specific powertrain combination to towyour vehicle with all four wheels on the ground (such as behind arecreational vehicle). These guidelines are designed to ensure that your transmission is notdamaged due to insufficient lubrication. All Front W...

STARTING Positions of the ignition 1. ACCESSORY, allows the electricalaccessories such as the radio tooperate while the engine is notrunning. 2. LOCK, locks the automatictransmission gearshift lever andallows key removal. 3. OFF, shuts off the engine withoutlocking the steering wheel. Thisposition a...

Starting the engine 1. Turn the key to 4 (ON) withoutturning the key to 5(START). 2. Turn the key to 5 (START), thenrelease the key as soon as theengine starts. Excessive crankingcould damage the starter. Note: If the engine does not start within five seconds on the first try, turn the key to OFF, w...

Even when the ABS is disabled,normal braking is still effective. (Ifyour BRAKE warning lampilluminates with the parking brakereleased, have your brake systemserviced immediately.) Parking brake To set the parking brake (1), pressthe parking brake pedal down untilthe pedal stops. To release, pull the...

During Traction Control 娂 operation, the traction control active light willilluminate, you may hear an electricmotor type of sound coming fromthe engine compartment and theengine will not “rev-up” when you push further on the accelerator. Thisis normal system behavior and should be no reason for con...

• Some noise is normal during operation. If the noise is excessive, checkfor low power steering pump fluid level before seeking service by yourauthorized dealer. • Heavy or uneven steering efforts may be caused by low power steeringpump fluid level. Check for low power steering pump fluid level befo...

If it is necessary to use the above procedure to move the gearshift lever,it is possible that a fuse has blown or the vehicle’s brakelamps are notoperating properly. Refer to Fuses and relays in the Roadside Emergencies chapter. Do not drive your vehicle until you verify that the brakelampsare worki...

If your vehicle gets stuck in mud or snow If your vehicle gets stuck in mud or snow, it may be rocked out byshifting between forward and reverse gears, stopping between shifts in asteady pattern. Press lightly on the accelerator in each gear. If necessary, try turning the Traction Control 娂 system o...

ROADSIDE ASSISTANCE Getting roadside assistance To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24–hours, seven days a week • for the...

Canadian customers refer to your Owner Information Guide forinformation on: • coverage period • exact fuel amounts • towing of your disabled vehicle • emergency travel expense reimbursement • travel planning benefits Using roadside assistance Complete the roadside assistance identification card and ...

HAZARD FLASHER The hazard flasher is located on thesteering column, just behind thesteering wheel. The hazard flasherswill operate when the ignition is inany position or if the key is not inthe ignition. Push in the flasher control and allfront and rear direction signals willflash. Press the flasher...

3. If no fuel leak is apparent, reset the fuel pump shut-off switch bypushing down on the reset button. 4. Turn the ignition to the ON position. Pause for a few seconds andreturn the key to the OFF position. 5. Make a further check for leaks in the fuel system. FUSES AND RELAYS Fuses If electrical c...

COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge Maxi fuses Fuse link cartridge 50A — — Red Red Red 60A — — Blue — Yellow 70A — — Tan — Brown 80A — — Natural — Black Passenger compartment fuse panel The fuse panel is located below and to the left of the steering wheel bythe brake ped...

Power distribution box The power distribution box islocated in the engine compartment.The power distribution box containshigh-current fuses that protect yourvehicle’s main electrical systemsfrom overloads. Always disconnect the battery before servicing high currentfuses. To reduce risk of electrical...

• Use snow chains on the end of the vehicle with the dissimilar sparetire/wheel The usage of a full-size dissimilar spare tire/wheel can lead toimpairment of the following: • Handling, stability and braking performance • Comfort and noise • Ground clearance and parking at curbs • Winter weather driv...

JUMP STARTING The gases around the battery can explode if exposed to flames,sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. Batteries contain sulfuric acid which can burn skin, eyes andclothing, if contacted. Do not attempt to push-start your automatic transmissionv...

Connecting the jumper cables 1. Connect the positive (+) jumper cable to the positive (+) terminal ofthe discharged battery. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2. Connect the other end of the positive (+) cable to the positive (+)termi...

3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery. 4. Make the final connection of the negative (-) cable. Make theconnection to an exposed metal part of the stalled vehicle’s engine, awayfrom the battery and the fuel injection system. Do not use fuel lines, engi...

Jump starting 1. Start the engine of the booster vehicle and run the engine atmoderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for anadditional three minutes before disconnecting the jumper cables. Removing the j...

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery. After the disabled vehicle has been started and the jumper cablesremoved, allow it to idle for several minutes so the...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider.It is recommended that your vehicle be towed with a wheel lift or flatbedequipment. Do not tow with a slingbe...

GETTING THE SERVICES YOU NEED At home You must take your Ford vehicle to an authorized dealer for warrantyrepairs. While any authorized dealer handling your vehicle line willprovide warranty service, we recommend you return to your sellingauthorized dealer who wants to ensure your continued satisfac...

THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM(U.S. ONLY) Your satisfaction is important to Ford Motor Company and to your dealer.Experience has shown that our customers have been very successful inachieving satisfaction by following the three-step procedure outlined onthe front page of the Warr...

authorized dealer to resolve a factory-related vehicle service concernhave been unsatisfactory, Ford of Canada participates in an impartialthird party mediation/arbitration program administered by the CanadianMotor Vehicle Arbitration Plan (CAMVAP). The CAMVAP program is a straight-forward and relat...

GETTING ASSISTANCE OUTSIDE THE U.S. AND CANADA Before exporting your vehicle to a foreign country, contact theappropriate foreign embassy or consulate. These officials can inform youof local vehicle registration regulations and where to find unleaded fuel. If you cannot find unleaded fuel or can onl...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3–A), which isavailable from your authorized dealer. • Never use strong household detergents or soap, such as dish washing orlaundry liquid. These products can dis...

• Do not allow paint sealant to come in contact with any non-body(low-gloss black) colored trim, such as grained door handles, roofracks, bumpers, side moldings, mirror housings or the windshield cowlarea. The paint sealant will “gray” or stain the parts over time. PAINT CHIPS Your authorized dealer...

• Spray Motorcraft Engine Shampoo and Degreaser (ZC-20) on all partsthat require cleaning and pressure rinse clean. • Cover the highlighted areas to prevent water damage when cleaningthe engine. • 3.0L Vulcan engine • Never wash or rinse the engine while it is running; water in therunning engine may...

• The wiper blades can be cleaned with isopropyl (rubbing) alcohol orMotorcraft Premium Windshield Washer Concentrate (ZC-32–A),available from your authorized dealer. This washer fluid containsspecial solution in addition to alcohol which helps to remove the hotwax deposited on the wiper blade and w...

• Remove light stains and soil with Motorcraft Professional StrengthCarpet & Upholstery Cleaner (ZC-54). • If grease or tar is present on the material, spot-clean the area firstwith Motorcraft Spot and Stain Remover (ZC-14). • If a ring forms on the fabric after spot cleaning, clean the entire a...

FORD AND LINCOLN MERCURY CAR CARE PRODUCTS Your Ford or Lincoln Mercury authorized dealer has many qualityproducts available to clean your vehicle and protect its finishes. Thesequality products have been specifically engineered to fulfill yourautomotive needs; they are custom designed to complement...

SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easylocation. • We provide scheduled maintenance information which makes tracking routine service easy. If your vehicle requires professional service, your authorized dealer ca...

OPENING THE HOOD 1. Inside the vehicle, pull the hoodrelease handle located under thebottom of the instrument panel. 2. Go to the front of the vehicle andrelease the auxiliary latch located inthe center between the hood andthe grille. 3. Lift the hood until the liftcylinders hold it open. 2007 Tauru...

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely. Only use a washer fluid that meetsFord specification WSB-M8B16-A2.Do not use any special washer fluidsuch as windshield water repellenttype fluid or bug wash. They m...

CHANGING THE WIPER BLADES 1. Pull the wiper arm away from thevehicle. Turn the blade at an anglefrom the wiper arm. Push the lockpin manually to release the bladeand pull the wiper blade downtoward the windshield to remove itfrom the arm. 2. Attach the new wiper to thewiper arm and press it into pla...

• 3.0L Vulcan engine 6. Wipe the indicator clean. Insert the indicator fully, then remove itagain. • If the oil level is between the two holes or between the MIN and MAX marks (depending on application), the oil level is acceptable. DO NOT ADD OIL. • If the oil level is at or below the lower hole or...

7. Put the indicator back in and ensure it is fully seated. Adding engine oil 1. Check the engine oil. For instructions, refer to Checking the engine oil in this chapter. 2. If the engine oil level is not within the normal range, add only certifiedengine oil of the recommended viscosity. Remove the ...

Do not use supplemental engine oil additives, cleaners or other enginetreatments. They are unnecessary and could lead to engine damage thatis not covered by Ford warranty. Change your engine oil and filter according to the appropriate schedulelisted in scheduled maintenance information. Ford product...

When lifting a plastic-cased battery, excessive pressure on theend walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery.Lift the battery with a battery carrier or with your hands on oppositecorners. Keep batteries out of reach of ...

• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recycling centerto find out more about recyclingautomotive batteries. ENGINE COOLANT Checking engine coolant The concentration and level of engine coolant sho...

When the engine is cold, check thelevel of the engine coolant in thereservoir. • The engine coolant should be at the “FULL COLD” level or within the“COLD FILL RANGE” as listed on the engine coolant reservoir(depending upon application). • Refer to scheduled maintenance information for service interv...

Do not add engine coolant when the engine is hot. Steam andscalding liquids released from a hot cooling system can burn you badly. Also, you can be burned if you spill coolant on hot engine parts. Do not put engine coolant in the windshield washer fluidcontainer. If sprayed on the windshield, engine...

remove the coolant pressure relief cap on the radiator of a vehicle withan overflow system, follow these steps to add engine coolant. To reduce the risk of personal injury, make sure the engine iscool before unscrewing the coolant pressure relief cap. The cooling system is under pressure; steam and ...

Used engine coolant should be disposed of in an appropriate manner. Follow your community’s regulations and standards for recyclingand disposing of automotive fluids. Coolant refill capacity To find out how much fluid your vehicle’s cooling system can hold, referto Maintenance product specifications...

WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELS Important safety precautions Do not overfill the fuel tank. The pressure in an overfilled tankmay cause leakage and lead to fuel spray and fire. The fuel system may be under pressure. If the fuel filler cap isventing vapor or if you hear a hissing sound, w...

• Avoid getting fuel liquid in your eyes. If fuel is splashed in the eyes,remove contact lenses (if worn), flush with water for 15 minutes andseek medical attention. Failure to seek proper medical attention couldlead to permanent injury. • Fuels can also be harmful if absorbed through the skin. If f...

Use the following guidelines to avoid electrostatic charge build-up whenfilling an ungrounded fuel container: • Place approved fuel container on the ground. • DO NOT fill a fuel container while it is in the vehicle (including thecargo area). • Keep the fuel pump nozzle in contact with the fuel conta...

Do not be concerned if your engine sometimes knocks lightly. However, ifit knocks heavily under most driving conditions while you are using fuelwith the recommended octane rating, see your authorized dealer toprevent any engine damage. Fuel quality If you are experiencing starting, rough idle or hes...

Replace the fuel filter with an authorized Motorcraft part. Thecustomer warranty may be void for any damage to the fuel systemif an authorized Motorcraft fuel filter is not used. ESSENTIALS OF GOOD FUEL ECONOMY Measuring techniques Your best source of information about actual fuel economy is you, th...

• Have the vehicle loading and distribution the same every time. Your results will be most accurate if your filling method is consistent. Calculating fuel economy 1. Fill the fuel tank completely and record the initial odometer reading(in miles or kilometers). 2. Each time you fill the tank, record ...

Readiness for Inspection/Maintenance (I/M) testing In some localities, it may be a legal requirement to pass an I/M test ofthe on-board diagnostics system. If the indicator is on, refer to the description in the Warning lights and chimes section of the Instrument Cluster chapter. Your vehicle may no...

4. Check the fluid level on thedipstick. It should be between thearrows in the FULL HOT range. Donot add fluid if the level is withinthis range. 5. If the fluid is low, add fluid in small amounts, continuously checkingthe level until it reaches the FULL HOT range. Be sure to put thedipstick back in ...

Adjusting automatic transmission fluid levels Before adding any fluid, make sure the correct type is used. The type offluid used is normally indicated on the dipstick. Refer to Maintenance product specifications and capacities in this chapter. Use of a non-approved automatic transmission fluid may c...

The Vehicle Identification Number (VIN) contains the followinginformation: 1. World manufacturer identifier 2. Brake system / Gross VehicleWeight Rating (GVWR) / RestraintSystem 3. Vehicle line, series, body type 4. Engine type 5. Check digit 6. Model year 7. Assembly plant 8. Production sequence nu...

GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for yourvehicle through your local Ford or Ford of Canada dealer. These qualityaccessories have been specifically engineered to fulfill your automotiveneeds; they are custom designed to complement th...

Peace of mind Remote start Vehicle security systems Wheel locks For maximum vehicle performance, keep the following information inmind when adding accessories or equipment to your vehicle: • When adding accessories, equipment, passengers and luggage to yourvehicle, do not exceed the total weight cap...

A Accessory delay ..........................44 Air cleaner filter .......................218 Air conditioning ..........................25 Airbag supplemental restraintsystem ............................97–98, 106 and child safety seats ..............99description ........................98, 106disp...

headlamps, flash to pass ..........30instrument panel, dimming .....30interior lamps ...............32–33, 35replacing bulbs .........................35 Lane change indicator(see Turn signal) ........................32 Lights, warning and indicator ....10 anti-lock brakes (ABS) ..........149 Load li...