Ford 2007 Mustang- Manuals

Special instructions For your added safety, your vehicle is fitted with sophisticated electroniccontrols. Please read the section Supplemental restraint system (SRS) in the Seating and Safety Restraints chapter. Failure to follow the specific warnings and instructions could result in personal injury...

To access this information, special equipment must be directly connectedto the recording modules. Ford Motor Company and Ford of Canada donot access event data recorder information without obtaining consent,unless pursuant to court order or where required by law enforcement,other government authorit...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat Child Seat InstallationWarning Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Brake Fluid -...

WARNING LIGHTS AND CHIMES Base instrument cluster Optional instrument cluster Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause extensive repairs. A warning light mayilluminate when a problem exists with one of your vehicle’s functions.Many lights ...

Service Engine Soon: The Service Engine Soon indicator light illuminates when the ignition is firstturned to the ON position to checkthe bulb. Solid illumination after the engine is started indicates the OnBoard Diagnostics System (OBD-II) has detected a malfunction. Refer to On board diagnostics (O...

Anti-lock brake system (ifequipped): If the ABS light stays illuminated or continues to flash, amalfunction has been detected, havethe system serviced immediately byyour authorized dealer. Normal braking is still functional unless the brakewarning light also is illuminated. Airbag readiness: If this...

Low tire pressure warning: Illuminates when your tire pressureis low. If the light remains ON atstart up or while driving, the tirepressure should be checked. Referto Inflating Your Tires in the Tires, Wheels and Loading chapter. When the ignition is first turned to ON, the light will illuminate for...

GAUGES Base instrument cluster gauges Optional instrument cluster gauges Refer to Message Center (if equipped) in the Driver Controls chapter to select one of six preset colors or one user definable color (MyColor)for the nighttime gauge backlighting. 2007 05+ Mustang (197) Owners Guide (post-2002-f...

AUDIO SYSTEMSAM/FM stereo / single CD/MP3 sound system (if equipped) Accessory delay: Your vehicle is equipped with accessory delay. With this feature, the window switches and radio may be used for up to tenminutes after the ignition switch is turned to the OFF position or untilany door or trunk is ...

Speed sensitive volume: Radio volume changes automatically and slightly with vehicle speed to compensate for road and wind noise.Recommended level is 1–3. Level 0 turns the feature off and level 7 isthe maximum setting.Press MENU to access and use / to adjust the volume setting. The level will appea...

In CATEGORY MODE, press / to scroll through the list of available Sirius channel Categories (Pop, Rock, News, etc.). Refer to Category Mode under Menu for further information. Satellite radio is available only with a valid SIRIUS subscription.Check with your authorized dealer for availability. 2. Ph...

To view the station name or type: When the desired category appears in the display, press TEXT/SCAN to toggle between displaying the stationtype (COUNTRY, ROCK, etc.) or the station name (WYCD, WXYZ, etc.). 4. AUX: Press to cycle through toggle between SAT1, SAT2 andSAT3 (Satellite Radio mode, ifequ...

20. CD slot: Insert one CD/MP3 at a time, label side up, when thesystem prompts to load a CD. MP3 track and folder structure Your MP3 system recognizes MP3 individual tracks and a folder structureas follows: • There are two different modes for MP3 disc playback: MP3 track mode(system default) and MP...

To play your portable music player using the auxiliary input jack: 1. Begin with the vehicle parked and the radio turned off.2. Ensure that the battery in your portable music player is new or fullycharged and that the device is turned off.3. Attach one end of the audio extension cable to the headpho...

GENERAL AUDIO INFORMATION Radio frequencies: AM and FM frequencies are established by the Federal CommunicationsCommission (FCC) and the Canadian Radio and TelecommunicationsCommission (CRTC). Those frequencies are: AM - 530, 540–1600, 1710 kHz FM- 87.7, 87.9–107.7, 107.9 MHz Radio reception factors...

Audio system warranty and service: Refer to the Warranty Guide for audio system warranty information. If service is necessary, see your dealer or qualified technician. Satellite radio information (if equipped) Satellite radio channels: SIRIUS broadcasts a variety of music, news, sports, weather, tra...

MANUAL HEATING AND AIR CONDITIONING SYSTEM 1. Temperature selection: Controls the temperature of the airflow in the vehicle. 2. Mode selections: Controls the location of the airflow in the vehicle. See the following for a brief description of each selection. MAX A/C: Distributes recirculated air thr...

4. Passenger heated seat: Press to activate or deactivate the passenger side heated seat. Note: The passenger heated seat will turn off automatically after 10 minutes of use. 5. Rear defroster (R ): Press to activate/deactivate the rear window defroster. Refer to Rear window defroster later in this ...

For maximum cooling performance in panel or panel/floor modes: 1. Move temperature control to the coolest setting. 2. Select A/C and recirculated air ( ) to provide colder airflow. 3. Set the fan to the highest speed initially, then adjust to maintaincomfort. To aid in side window defogging/demistin...

CABIN AIR FILTER Your vehicle is equipped with a cabin air filter, which is located just infront of the windshield under the cowl grille on the passenger side of thevehicle. The particulate air filtration system is designed to reduce theconcentration of airborne particles such as dust, spores and po...

HEADLAMP CONTROL Turns the lamps off. Turns on the parking lamps, instrument panel lamps, licenseplate lamps and tail lamps. Turns the headlamps on. Foglamp control (if equipped) The foglamps can be turned onwhen the ignition is in the ONposition, the headlamp control is inthe or position and the hi...

Flash to pass Pull toward you, to the first detent,to activate and release to deactivate. Daytime running lamps (DRL) (if equipped) Turns the headlamps on with a reduced output. When activated, the DRLtelltale is illuminated.To activate: • the ignition must be in the ON position, • the headlamp cont...

If your vehicle has been in an accident the alignment of your headlampsshould be checked by your authorized dealer. Vertical aim adjustment 1. Park the vehicle directly in front of a wall or screen on a level surface,approximately 25 feet (7.6 meters) away. • (1) 8 feet (2.4 meters) • (2) Center hei...

Function Trade Number Headlamp H13 Park lamp, turn lamp, side marker (front) 3157 or 3157K Sidemarker (front) W5W or W5WL Fog lamp 9145–GT or H11–Pony (if equipped) Tail lamp, brakelamp, turn lamp 3057K or 4057K Sidemarker (rear) W5W or W5WL High-mount brakelamp 921 Backup lamp 921 License plate lam...

MULTI-FUNCTION LEVER Windshield wiper: For intermittent operation, move control up oneposition. Adjust the rotary control to thedesired speed setting. For normal or low speed wiperoperation, move control up twopositions from OFF. For high speed wiper operation,move control up three positionsfrom OFF...

TILT STEERING WHEEL (IF EQUIPPED) To adjust the steering wheel: 1. Push the lever down to unlockthe steering column. While the leveris in the down position, tilt thesteering column to its desiredorientation. 2. While holding the steeringcolumn, pull the lever up to itsoriginal position to lock the s...

The power point is an additionalpower source for electricalaccessories. The power points arelocated on the instrument panel andinside the center console storagebin. Do not use the power point foroperating the cigarette lighterelement (if equipped). To prevent the fuse from beingblown, do not use the...

Press and pull the switches to openand close windows. • Push down (to the first detent)and hold the switch to open. • Pull up (to the first detent) andhold the switch to close. Express down (One Touch Down, Front windows only) Allows the driver and passenger’swindow to open fully withoutholding the ...

Bounce Back (Front windows only) When an obstacle has been detected in the window opening as thewindow is moving upward, the window will automatically move down andstop at a prescribed position. Bounce Back Override (Front windows only) To override Bounce Back, within 2 seconds after reaching Bounce...

AUTOMATIC DIMMING INSIDE REAR VIEW MIRROR (IF EQUIPPED) Your vehicle is equipped with aninside rear view mirror which has anauto-dimming function. Theelectrochromic day/night mirror willchange from the normal (highreflective) state to the non-glare(darkened) state when bright lights (glare) reach th...

EXTERIOR MIRRORS Power side view mirrors To adjust your mirrors: 1. Rotate the control clockwise toadjust the right mirror and rotatethe control counterclockwise toadjust the left mirror. 2. Move the control in the directionyou wish to tilt the mirror. 3. Return to the center position to lock mirror...

• Depress the brake pedal until thedesired vehicle speed is reached,press the SET + control. Turning off speed control There are two ways to turn off the speed control: • Press the speed control OFFcontrol. • Turn OFF the ignition. Note: When you turn off the speed control or the ignition, your spee...

The latch handles must be pulleddownwards fully to allow thelatch to fully rotate into theopen position 3. Unclamp the top from thewindshield header by pulling eachlatch handle down and then rotatingthe latch to the rear until it clearsthe header. Note: If the top has not been lowered for some time ...

Installation of the boot (if equipped) Be sure the boot is secure on the vehicle before driving. 1. Install the boot on the vehicle by hooking the boot retaining clips onthe back panel.2. Install the boot on the right side tucking in the front part of the bootin the quarter panel and hooking the ret...

Storing the boot 1. Position the boot right-side up and fold each side of the boot inward. 2. Turn the boot upside down and fold the left side of the boot inward. 3. Fold the right side inward and secure the boot with the strap. Stow the boot in the trunk. Raising the convertible top The convertible...

MESSAGE CENTER (IF EQUIPPED) With the ignition in the ON position,the message center, located on yourinstrument cluster, displaysimportant vehicle information through a constant monitor ofvehicle systems. You may select display features on the message center for a display of status. Thesystem will a...

Pressing the RESET control cycles the message center through each ofthe systems being monitored. The sequence of the system check report and how it appears in themessage center is as follows: 1. OIL PRESSURE 2. CHARGING SYSTEM 3. DRIVER DOOR 4. PASSENGER DOOR 5. TRUNK 6. BRAKE SYSTEM 7. SECURITY SYS...

Adjusting MyColor 娂 : MyColor 娂 is a user defined backlighting color. The backlighting colors are achieved through the blending of light fromRed, Green, and Blue LEDs. Apart from the 6 preset colors, drivers cancreate their own color by adjusting the levels of the three primary colorsthrough the MyC...

2. Pressing the RESET controlcycles the message center througheach of the language choices. 3. Press and hold the RESETcontrol to set the language choice. Info menu This control displays the followingcontrol displays: • Odometer • Trip odometer • Distance to Empty • Average Fuel Economy • Instantane...

Dual mode display The DTE function will display LOW FUEL LEVEL and sound a tone forone second when you have approximately 50 miles (80 km) to empty. Ifyou RESET this warning message, this display and tone will returnwithin 10 minutes. DTE is calculated using a running average fuel economy, which is ...

System warnings System warnings alert you to possible problems or malfunctions in yourvehicle’s operating systems. In the event of a multiple warning situation, the message center willcycle the display to show all warnings by displaying each one for 4seconds. The message center will display the last...

CHECK TRACTION CONTROL 娂 . Displayed when the Traction Control 娂 system is not operating properly. If this message is displayed on the message center the Traction Control 娂 system will be partially operable. If this warning stays on, contact your authorized dealer forservice as soon as possible. For...

KEYS One key operates all the locks and starts the vehicle. Always carry aspare key with you in case of an emergency. Your keys are programmed to your vehicle; using a non-programmed keywill not permit your vehicle to start. If you lose your authorized dealersupplied keys, replacement keys are avail...

Central locking and unlocking feature Your vehicle’s keys are designed to lock and unlock the driver’s door, aswell as open the trunk. • The driver’s door is unlocked when the key is inserted in the driverdoor key cylinder and turned to the unlock position. The driver’s dooris locked when the key is...

INTERIOR LUGGAGE COMPARTMENT RELEASE Your vehicle is equipped with a mechanical interior luggage compartmentrelease handle that provides a means of escape for children and adults inthe event they become locked inside the luggage compartment.Adults are advised to familiarize themselves with the opera...

To replace the battery: 1. Twist a thin coin between the twohalves of the remote entrytransmitter near the key ring. DONOT TAKE THE RUBBER COVERAND CIRCUIT BOARD OFF THEFRONT HOUSING OF THEREMOTE ENTRY TRANSMITTER. 2. Do not wipe off any grease on thebattery terminals on the backsurface of the circu...

The battery saver will shut off the interior lamps 10 minutes after theignition has been turned to the 1 (OFF/LOCK) position and a door is leftopen, and in 30 minutes if the dome lamp control is left on and theignition has been turned to the 1 (OFF/LOCK) position. The batterysaver will also shut off...

At this point, perimeter lighting will be activated if it was previouslydeactivated, and deactivated if it was previously activated. Confirmationof perimeter lighting being activated is provided by a short horn chirpfollowed by a long horn sound; Confirmation of perimeter lighting beingdeactivated i...

If a problem occurs with the SecuriLock 娂 system, the indicator will flash rapidly or glow steadily when the ignition is in the 3 (ON) position. Ifthis occurs, the vehicle should be taken to an authorized dealer forservice. Automatic arming The vehicle is armed immediatelyafter switching the ignitio...

Programming spare keys You can program your own coded keys to your vehicle. Please read andunderstand the entire procedure before you begin. Tips: • A maximum of eight keys can be coded to your vehicle. • Only use SecuriLock 娂 keys. • You must have two previously programmed coded keys (keys thatalre...

If there is any potential active anti-theft problem with your vehicle,ensure ALL remote entry transmitters are taken to an authorized dealer to aid in troubleshooting. Arming the system When armed, the active anti-theft system is designed to notify you of anunauthorized entry. When unauthorized entr...

SEATING Notes: Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in the event of a collision. Do not pile cargo higher than the seatbacks to reduce the risk ofinjury in a collision or sudden stop. Before returning the seatback to...

Rear seat entry/exit Use the seatback release to fold theback of the front seat forward forrear seat access. This release handleis located on the upper back of thefront seat. The seatback locksautomatically when returned to thenormal position. Use the recliner handle to returnthe seatback to the des...

Before returning the seatback to its original position, make surethat cargo or any objects are not trapped behind the seatback. After returning the seatback to its original position, pull on theseatback to ensure that it has fully latched. An unlatched seat maybecome dangerous in the event of a sudd...

Air bags can kill or injure a child in a child seat. NEVER place a rear-facing child seat in front of an active air bag. If you must use a forward-facing child seat in the front seat, move the seat all theway back. Always transport children 12 years old and under in the backseat and always properly ...

Front safety belt energy management retractors The front outboard safety belt energy management retractors allowwebbing to be pulled out of the retractor in a gradual and controlledmanner in response to the occupant’s forward momentum. This helpsreduce the risk of force-related injuries to the occup...

Never let a passenger hold a child on his or her lap while thevehicle is moving. The passenger cannot protect the child from injury in a collision. All occupants of the vehicle, including the driver, should alwaysproperly wear their safety belts, even when an airbag supplemental restraint system (SR...

1. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) until you hear a snap and feelit latch. Make sure the tongue issecurely fastened in the buckle. 2. To unfasten, push the releasebutton and remove the tongue fromthe buckle. The center of the...

After any vehicle collision, the safety belt system at all outboardseating positions (except driver, which has no “automatic locking retractor” feature) must be checked by an authorized dealer to verifythat the “automatic locking retractor” feature for child seats is stillfunctioning properly. In ad...

After any vehicle collision, the front passenger and rear outboardsafety belt systems must be checked by an authorized dealer to verify that the “automatic locking retractor” feature for child seats isstill functioning properly. In addition, all safety belts should be checkedfor proper function. BEL...

Do not use extensions to change the fit of the shoulder beltacross the torso. Safety belt maintenance Inspect the safety belt systems periodically to make sure they workproperly and are not damaged. Inspect the safety belts to make surethere are no nicks, tears or cuts. Replace if necessary. All saf...

Conditions of operation If... Then... The driver’s safety belt is notbuckled before the ignitionswitch is turned to the ONposition... The safety belt warning lightilluminates1-2 minutes and thewarning chime sounds 4-8 seconds. The driver’s safety belt isbuckled while the indicatorlight is illuminate...

The following are reasons most often given for not wearing safety belts(All statistics based on U.S. data): Reasons given... Consider... “Crashes are rare events” 36700 crashes occur every day. The more we drive, the more we areexposed to “rare” events, even forgood drivers. 1 in 4 of us will be ser...

Reasons given... Consider... “I have an airbag” Airbags offer greater protection whenused with safety belts. Frontal airbagsare not designed to inflate in rear andside crashes or rollovers. “I’d rather be thrown clear” Not a good idea. People who are ejected are 40 times more likelyto DIE. Safety be...

AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) Important SRS precautions The SRS is designed to work withthe safety belt to help protect thedriver and right front passengerfrom certain upper body injuries.Airbags DO NOT inflate slowly;there is a risk of injury from adeploying airbag. All occupants of th...

Never place your arm over the airbag module as a deployingairbag can result in serious arm fractures or other injuries. To properly position yourself away from the airbag: • Move your seat to the rear as far as you can while still reaching thepedals comfortably. • Recline the seat slightly one or tw...

Children and airbags Children must always be properlyrestrained. Accident statisticssuggest that children are safer whenproperly restrained in the rearseating positions than in the frontseating position. Failure to followthese instructions may increase therisk of injury in a collision. Airbags can k...

Several air bag system components get hot after inflation. Do nottouch them after inflation. If the air bag has deployed, the air bag will not function again and must be replaced immediately. If the air bag is not replaced, the unrepaired area will increase the risk of injury in acollision. Front pa...

The front passenger sensing systemuses a ⬙ passenger airbag off ⬙ or ⬙ pass airbag off ⬙ indicator which will illuminate and stay lit to remind youthat the front passenger frontal airbag is disabled. The indicator lamp islocated on the top right corner of the center stack of the instrumentpanel abov...

In case there is a problem with thefront passenger sensing system, theairbag readiness lamp in theinstrument cluster will stay lit. If the airbag readiness lamp is lit, do the following: The driver and/or adult passengers should check for any objects thatmay be lodged underneath the front passenger ...

The side airbags are fitted on the outboard side of the seatbacks of thefront seats. In certain lateral collisions, the airbag on the side affected bythe collision will be inflated. The front passenger sensing system willturn off the passenger seat side airbag if the seat is empty. The airbagwas des...

A difficulty with the system is indicated by one or more of the following: • The readiness light will eitherflash or stay lit. • The readiness light will notilluminate immediately afterignition is turned on. • A series of five beeps will be heard. The tone pattern will repeatperiodically until the p...

Children and safety belts If the child is the proper size, restrain the child in a safety seat. Childrenwho are too large for child safety seats (as specified by your child safetyseat manufacturer) should always wear safety belts. Follow all the important safety restraint and airbag precautions that...

Booster seats should be used until you can answer YES to ALL of thesequestions: • Can the child sit all the way backagainst the vehicle seat back withknees bent comfortably at theedge of the seat withoutslouching? • Does the lap belt rest low across the hips? • Is the shoulder belt centered on the s...

Carefully follow all of the manufacturer’s instructions includedwith the safety seat you put in your vehicle. If you do not install and use the safety seat properly, the child may be injured in a suddenstop or collision. Rear-facing child seats or infant carriers should never be placedin front of an...

5. To put the retractor in theautomatic locking mode, grasp theshoulder portion of the belt and pulldownward until all of the belt isextracted and a click is heard. 6. Allow the belt to retract. The belt will click as it retracts to indicate itis in the automatic locking mode. 7. Pull the lap belt p...

Attaching child safety seats with tether straps Most new forward-facing child safety seats include a tether strap whichgoes over the back of the seat and hooks to an anchoring point. Tetherstraps are available as an accessory for many older safety seats. Contactthe manufacturer of your child seat fo...

Note: The attachments for the convertible boot located on the backof the head restraints are not tetheranchors. 4. Access tether anchors locatedbehind the seatback under the vinyltag marked with the child tetheranchor symbol. 2007 05+ Mustang (197) Owners Guide (post-2002-fmt)USA (fus) Seating and S...

INFORMATION ABOUT UNIFORM TIRE QUALITY GRADING New vehicles are fitted with tiresthat have a rating on them calledTire Quality Grades. The Qualitygrades can be found whereapplicable on the tire sidewallbetween tread shoulder andmaximum section width. Forexample: • Treadwear 200 Traction AA Temperatu...

The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning or peak traction characteristics. Temperature A B C The temperature grades are A (the highest), B and C, representing thetire’s resistance to the gene...

Under-inflation is the most common cause of tire failures andmay result in severe tire cracking, tread separation or ⬙ blowout ⬙ , with unexpected loss of vehicle control and increased risk of injury.Under-inflation increases sidewall flexing and rolling resistance,resulting in heat buildup and inte...

Note: If you have to drive a distance to get air for your tire(s), check and record the tire pressure first and add the appropriate air pressurewhen you get to the pump. It is normal for tires to heat up and the airpressure inside to go up as you drive. 2. Remove the cap from the valve on one tire, ...

Tire wear When the tread is worn down to1/16th of an inch (2 mm), tires mustbe replaced to help prevent yourvehicle from skidding andhydroplaning. Built-in treadwearindicators, or “wear bars”, whichlook like narrow strips of smoothrubber across the tread will appearon the tire when the tread is worn...

built. For example, the numbers 317 mean the 31st week of 1997. After2000 the numbers go to four digits. For example, 2501 means the 25thweek of 2001. The numbers in between are identification codes used fortraceability. This information is used to contact customers if a tire defectrequires a recall...

Important: Remember to replace the wheel valve stems when the road tires are replaced on your vehicle. It is recommended that the two front tires or two rear tires generally bereplaced as a pair. The tire pressure sensors mounted in the wheels (originally installed onyour vehicle) are not designed t...

Tire and wheel alignment A bad jolt from hitting a curb or pothole can cause the front end of yourvehicle to become misaligned or cause damage to your tires. If yourvehicle seems to pull to one side when you’re driving, the wheels may beout of alignment. Have an authorized dealer check the wheel ali...

4. R: Indicates a “radial” type tire. 5. 15: Indicates the wheel or rim diameter in inches. If you change your wheel size, you will have to purchase new tires to match the new wheeldiameter. 6. 95: Indicates the tire’s load index. It is an index that relates to how much weight a tire can carry. You ...

13. Maximum Permissible Inflation Pressure: Indicates the tire manufacturers’ maximum permissible pressure and/or the pressure atwhich the maximum load can be carried by the tire. This pressure isnormally higher than the manufacturer’s recommended cold inflationpressure which can be found on the Saf...

Information on “T” type tires “T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: T145/80D16 is an example of a tiresize. Note: The temporary tire size for your vehicle may be different fromthis example. 1. T: Indicates a type of tire, ...

Changing tires with TPMS Each road tire is equipped witha tire pressure sensor fastenedto the inside rim of the wheel.The pressure sensor is coveredby the tire and is not visibleunless the tire is removed. Thepressure sensor is locatedopposite (180 degrees) from thevalve stem. Care must be takenwhen...

When you believe your system is not operating properly The main function of the Tire Pressure Monitoring System is to warn youwhen your tires need air. It can also warn you in the event the system is nolonger capable of functioning as intended. Please refer to the followingchart for information conc...

Low Tire PressureWarning Light Possible cause Customer Action Required Flashing WarningLight Spare tire in use Your temporary spare tire is in use. Repair the damaged roadwheel and re-mount it on thevehicle to restore systemfunctionality. For a descriptionof how the system functionsunder these condi...

SNOW TIRES AND CHAINS Driving too fast for conditions creates the possibility of loss ofvehicle control. Driving at very high speeds for extended periods of time may result in damage to vehicle components. Snow tires must be the same size and grade as the tires youcurrently have on your vehicle. The...

Base Curb Weight – is the weight of the vehicle including a full tank of fuel and all standard equipment. It does not include passengers, cargo, oroptional equipment. Vehicle Curb Weight – is the weight of your new vehicle when you picked it up from your authorized dealer plus any aftermarketequipme...

Example only: Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue loador king pin weight is also part of cargo weight. GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehi...

GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Labellocated on the B-Pillar or the edge of the driver’s door. The totalload on each axle must never exceed its GAWR....

If you use a rental trailer, follow the instructions that the rental agencygives to you. Do not attach safety chains to the bumper. Trailer brakes Electric brakes and manual, automatic or surge-type trailer brakes aresafe if installed properly and adjusted to the manufacturer’sspecifications. The tr...

Trailer towing tips • Practice turning, stopping and backing up before starting on a trip toget the feel of the vehicle trailer combination. When turning, makewider turns so the trailer wheels will clear curbs and other obstacles. • Allow more distance for stopping with a trailer attached. • The tra...

STARTING Positions of the ignition 1. OFF/LOCK, locks the steeringwheel, automatic transmissiongearshift lever and allows keyremoval. Note: The ignition key cannot be removed from the ignition unlessthe gearshift lever is securelylatched in P (Park). 2. ACCESSORY, allows the electricalaccessories su...

3. Turn the key to 3 (ON) withoutturning the key to 4 (START). Some warning lights will briefly illuminate. See Warning lights and chimes in the Instrument Cluster chapter for more information regarding the warning lights. Starting the engine 1. Turn the key to 3 (ON) withoutturning the key to 4 (ST...

ABS warning lamp The ABS lamp in the instrumentcluster momentarily illuminateswhen the ignition is turned on. Ifthe light does not illuminate duringstart up, remains on or flashes, theABS may be disabled and may need to be serviced. Even when the ABS is disabled,normal braking is still effective. (I...

Always set the parking brake fully and make sure that thegearshift is securely latched in P (Park) (automatic transmission) or in 1 (First) (manual transmission). If the parking brake is fully released, but the brake warning lampremains illuminated, the brakes may not be working properly. See your a...

The Traction Control 娂 switch, located above the radio, illuminateswhen the system is off. The TractionControl 娂 system will automatically turn on every time the ignition isturned OFF and ON. If you should become stuck in snowor ice or on a very slippery roadsurface, try switching the TractionContro...

• To return to Overdrive mode, press the transmission control switch.The O/D OFF lamp will not be illuminated. • Overdrive mode is automatically returned each time the key is turnedoff. 3 (Third) This position allows for third gear only. • Provides engine braking. • To return to D (Drive) without Ov...

Do not rock the vehicle for more than a minute or damage to thetransmission and tires may occur, or the engine may overheat. MANUAL TRANSMISSION OPERATION (IF EQUIPPED) Using the clutch The manual transmission has a starter interlock that prevents crankingthe engine unless the clutch pedal is fully ...

Recommended shift speeds Do not downshift into 1 (First) when your vehicle is movingfaster than 15 mph (24 km/h). This will damage the clutch. Upshift according to the following chart: Upshifts when accelerating (recommended for best fuel economy) Shift from: 1 - 2 11 mph (18 km/h) 2 - 3 19 mph (31 ...

DRIVING THROUGH WATER If driving through deep or standingwater is unavoidable, proceed veryslowly especially when the depth isnot known. Never drive throughwater that is higher than the bottomof the wheel rims (for cars) or thebottom of the hubs (for trucks). When driving through water, traction or ...

ROADSIDE ASSISTANCE Getting roadside assistance To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24–hours, seven days a week • for the...

Canadian customers refer to your Owner Information Guide forinformation on: • coverage period • exact fuel amounts • towing of your disabled vehicle • emergency travel expense reimbursement • travel planning benefits Using roadside assistance Complete the roadside assistance identification card and ...

HAZARD FLASHER CONTROL The hazard flasher is located on theinstrument panel by the radio. Thehazard flashers will operate whenthe ignition is in any position or ifthe key is not in the ignition. Push in the flasher control and allfront and rear direction signals will flash. Press the flasher control...

FUSES AND RELAYS Fuses If electrical components in thevehicle are not working, a fuse mayhave blown. Blown fuses areidentified by a broken wire withinthe fuse. Check the appropriatefuses before replacing any electricalcomponents. Note: Always replace a fuse with one that has the specified amperage r...

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 14 5A A/C cycle switch 15 10A Brake On/Off (BOO) power 16 5A Cluster 17 10A Restraint Control Module (RCM),Passenger Occupant DetectionSystem (PODS), Passenger Airbag Deactivation Indicator (PADI) 18 10A Anti-lock Brake...

• hold the steering wheel firmly. • slowly move to a safe place on the side of the road. Your vehicle may be equipped with a conventional spare tire that isdifferent in one or more of the following: type, brand, size, speed ratingand tread design. If this is the case, this dissimilar spare tire is s...

• Load the vehicle beyond maximum vehicle load rating listed on theSafety Compliance Label • Tow a trailer • Use snow chains on the end of the vehicle with the dissimilar sparetire • Use more than one dissimilar spare tire at a time • Use commercial car washing equipment • Try to repair the dissimil...

• All-Wheel driving capability (if applicable) • Load leveling adjustment (if applicable) When driving with the full-size dissimilar spare tire/wheel additionalcaution should be given to: • Towing a trailer • Driving vehicles equipped with a camper body • Driving vehicles with a load on the cargo ra...

3. Place the gearshift lever in P (Park) (automatic transmission) or R(Reverse) (manual transmission). 4. Set the parking brake. 5. Turn off the ignition. To change the tire: Note: Passengers should not remain in the vehicle when the vehicle is being jacked. 1. Block both the front and rear ofthe wh...

8. Remove the jack and fully tightenthe lug nuts in the order shown.Refer to Wheel lug nut torque specifications later in this chapter for the proper lug nut torquespecification. 9. Put flat tire, wheel ornament (ifequipped), jack and lug wrenchaway. Make sure jack is fastened soit does not rattle w...

Batteries contain sulfuric acid which can burn skin, eyes andclothing, if contacted. Do not attempt to push-start your automatic transmissionvehicle. Automatic transmissions do not have push-startcapability. Attempting to push-start a vehicle with an automatictransmission may cause transmission dama...

4. Make the final connection of the negative (-) cable to an exposedmetal part of the stalled vehicle’s engine, away from the battery and thecarburetor/fuel injection system. Do not use fuel lines, engine rocker covers or the intake manifold as grounding points. Do not connect the end of the second ...

Removing the jumper cables Remove the jumper cables in the reverse order that they wereconnected. 1. Remove the jumper cable from the ground metal surface. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2. Remove the jumper cable on the negative (...

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery. After the disabled vehicle has been started and the jumper cablesremoved, allow it to idle for several minutes so the...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift anddollies or flatbed equipment. Do not tow w...

GETTING THE SERVICES YOU NEED At home You must take your Ford vehicle to an authorized dealer for warrantyrepairs. While any authorized dealer handling your vehicle line willprovide warranty service, we recommend you return to your sellingauthorized dealer who wants to ensure your continued satisfac...

THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM(U.S. ONLY) Your satisfaction is important to Ford Motor Company and to your dealer.Experience has shown that our customers have been very successful inachieving satisfaction by following the three-step procedure outlined onthe front page of the Warr...

authorized dealer to resolve a factory-related vehicle service concernhave been unsatisfactory, Ford of Canada participates in an impartialthird party mediation/arbitration program administered by the CanadianMotor Vehicle Arbitration Plan (CAMVAP). The CAMVAP program is a straight-forward and relat...

Monday-Friday 8:00 a.m. - 6:00 p.m. EST Helm, Incorporated can also be reached by their website:www.helminc.com. (Items in this catalog may be purchased by credit card, check ormoney order.) Obtaining a French owner’s guide French Owner’s Guides can be obtained from your authorized dealer orby writi...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3–A), which isavailable from your authorized dealer. • Never use strong household detergents or soap, such as dish washingor laundry liquid. These products can dis...

• Wash the vehicle first. • Do not use waxes that contain abrasives; use Motorcraft PremiumLiquid Wax (ZC-53-A), which is available from your authorized dealer,or an equivalent quality product. • Do not allow paint sealant to come in contact with any non-body(low-gloss black) colored trim, such as g...

ENGINE Engines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing: • Take care when using a power washer to clean the engine. Thehigh-pressure fluid could penetrate the sealed parts and causedamage. • Do not spray a hot engine with ...

• 4.6L 3V SOHC V8 engine • Never wash or rinse the engine while it is running; water in therunning engine may cause internal damage. PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products areavailable from your authorized dealer. • For routine cleaning...

• The wiper blades can be cleaned with isopropyl (rubbing) alcohol orMotorcraft Premium Windshield Washer Concentrate (ZC-32–A),available from your authorized dealer. This washer fluid containsspecial solution in addition to alcohol which helps to remove the hotwax deposited on the wiper blade and w...

INTERIOR TRIM • Clean the interior trim areas with a damp cloth, then with a clean, drycloth; you may also use Motorcraft Dash & Vinyl Cleaner (ZC-38-A). • Do not use household or glass cleaners as these may damage thefinish. INTERIOR For fabric, carpets, cloth seats, safety belts and seats equi...

• Do not use household cleaning products, alcohol solutions, solvents orcleaners intended for rubber, vinyl and plastics, or oil/petroleum-basedleather conditioners. These products may cause premature wearing ofthe clear, protective coating. Note: In some instances, color or dye transfer can occur w...

SERVICE RECOMMENDATIONS To help you service your vehicle we provide scheduled maintenance information which makes tracking routine service easy. If your vehicle requires professional service, your authorized dealer canprovide the necessary parts and service. Check your Warranty Guide/Owner Informati...

2. Block the wheels. To reduce the risk of vehicle damage and/or personal burninjuries do not start your engine with the air cleaner removed and do not remove it while the engine is running. OPENING THE HOOD 1. Inside the vehicle, pull the hoodrelease handle located on thedriver’s side kick panel. 2...

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 4.0L SOHC V6 engine 1. Battery 2. Engine oil filler cap 3. Engine oil dipstick 4. Brake fluid reservoir 5. Air filter assembly 6. Power steering fluid reservoir 7. Engine coolant reservoir 8. Windshield washer fluid reservoir 9. Power distribution box...

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely. Only use a washer fluid that meetsFord specification WSB-M8B16-A2.Do not use any special washer fluidsuch as windshield water repellenttype fluid or bug wash. They m...

CHANGING THE WIPER BLADES 1. Pull the wiper arm away from thevehicle. Turn the blade at an anglefrom the wiper arm. Push the lockpin manually to release the bladeand pull the wiper blade downtoward the windshield to remove itfrom the arm. 2. Attach the new wiper to thewiper arm and press it into pla...

• 4.0L V6 engine • 4.6L 3V V8 engine 6. Wipe the indicator clean. Insert the indicator fully, then remove itagain. • If the oil level is between the lower and upper holes, the oil level is acceptable. DO NOT ADD OIL. • If the oil level is below the lower hole, add enough oil to raise thelevel within...

• 4.0L V6 engine • 4.6L 3V SOHC V8 engine • Oil levels above the upper hole may cause engine damage. Some oilmust be removed from the engine by an authorized dealer. 7. Put the indicator back in and ensure it is fully seated. 2007 05+ Mustang (197) Owners Guide (post-2002-fmt)USA (fus) Maintenance a...

Adding engine oil 1. Check the engine oil. For instructions, refer to Checking the engine oil in this chapter. 2. If the engine oil level is not within the normal range, add only certifiedengine oil of the recommended viscosity. Remove the engine oil filler capand use a funnel to pour the engine oil...

It is recommended you use the appropriate Motorcraft oil filter (oranother brand meeting Ford specifications) for your engine application. BATTERY Your vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice. If your batt...

Keep batteries out of reach of children. Batteries contain sulfuricacid. Avoid contact with skin, eyes or clothing. Shield your eyes when working near the battery to protect against possible splashing ofacid solution. In case of acid contact with skin or eyes, flushimmediately with water for a minim...

• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recycling centerto find out more about recyclingautomotive batteries. ENGINE COOLANT Checking engine coolant The concentration and level of engine coolant sho...

When the engine is cold, check thelevel of the engine coolant in thereservoir. • The engine coolant should be at the “FULL COLD” level or within the“COLD FILL RANGE” as listed on the engine coolant reservoir(depending upon application). • Refer to scheduled maintenance information for service interv...

Do not put engine coolant in the windshield washer fluidcontainer. If sprayed on the windshield, engine coolant could make it difficult to see through the windshield. • Add Motorcraft Premium Gold Engine Coolant or equivalentmeeting Ford specification WSS-M97B51-A1. Refer to Maintenance product spec...

To reduce the risk of personal injury, make sure the engine iscool before unscrewing the coolant pressure relief cap. The cooling system is under pressure; steam and hot liquid can come outforcefully when the cap is loosened slightly. 1. Before you begin, turn the engine off and let it cool. 2. When...

Used engine coolant should be disposed of in an appropriate manner. Follow your community’s regulations and standards for recyclingand disposing of automotive fluids. Coolant refill capacity To find out how much fluid your vehicle’s cooling system can hold, referto Maintenance product specifications...

4. Check the coolant level and replenish if low. Never remove the coolant reservoir cap while the engine isrunning or hot. 5. Restart the engine and take your vehicle to an authorized dealer. Driving the vehicle without repairing the engine problemincreases the chance of engine damage. Take your veh...

Refueling Fuel vapor burns violently and a fuel fire can cause severeinjuries. To help avoid injuries to you and others: • Read and follow all the instructions on the pump island; • Turn off your engine when you are refueling; • Do not smoke if you are near fuel or refueling your vehicle; • Keep spa...

The fuel system may be under pressure. If the fuel filler cap isventing vapor or if you hear a hissing sound, wait until it stops before completely removing the fuel filler cap. Otherwise, fuel mayspray out and injure you or others. If you do not use the proper fuel filler cap, excessive vacuum inth...

If you have run out of fuel: • You may need to cycle the ignition from OFF to ON several times afterrefueling to allow the fuel system to pump the fuel from the tank tothe engine. On restarting, cranking time will take a few seconds longerthan normal. • Normally, adding one gallon of fuel is enough ...

• Use the same filling rate setting (low — medium — high) each timethe tank is filled. • Allow no more than two automatic click-offs when filling. • Always use fuel with the recommended octane rating. • Use a known quality gasoline, preferably a national brand. • Use the same side of the same pump a...

POWER STEERING FLUID Check the power steering fluid.Refer to the scheduled maintenanceguide for the service intervalschedules. If adding fluid is necessary, use only MERCON 威 ATF . 1. Start the engine and let it rununtil it reaches normal operatingtemperature (the engine coolanttemperature gauge ind...

TRANSMISSION FLUID Checking automatic transmission fluid The 5R55S transmission does not have a transmission fluid dipstick. Refer to your scheduled maintenance information for scheduled intervals for fluid checks and changes. Your transmission does notconsume fluid. However, the fluid level should ...

Checking and adding manual transmission fluid (if equipped) 1. Clean the filler plug. 2. Remove the filler plug and inspect the fluid level. 3. Note: There are two different manual transmissions used in thisvehicle and they have different fluid levels. For vehicles equipped with aV6 engine the corre...

• Fill level for V6 • Fill level for V8 4. Add enough fluid through the filler opening to bring the fluid up tothe recommended levels.5. Install and tighten the fill plug securely.Use only fluid that meets Ford specifications. Refer to the Maintenance product specifications and capacities section in...

The Vehicle Identification Number (VIN) contains the followinginformation: 1. World manufacturer identifier 2. Brake system / Gross VehicleWeight Rating (GVWR) / RestraintSystem 3. Vehicle line, series, body type 4. Engine type 5. Check digit 6. Model year 7. Assembly plant 8. Production sequence nu...

GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for yourvehicle through your local Ford or Ford of Canada dealer. These qualityaccessories have been specifically engineered to fulfill your automotiveneeds; they are custom designed to complement th...

A Accessory delay ..........................51 Air cleaner filter .......................241 Airbag supplementalrestraint system ................106, 114 and child safety seats ............108description ......................106, 114disposal ....................................117driver airbag .......