Fisher-Price L0542 - Manuals

Page 2 - Prevent injury from burns:; WARNING; Consumer Information; • Please read these instructions before assembly and use of

2 Prevent serious injury or death from falls or sliding out: • The child should at all times wear a safety harness correctly fitted and adjusted. The tray is not designed to hold the child in the chair. • It is recommended that only children capable of sitting upright unassisted use the high chair i...

Page 3 - Assembled Parts; Tighten or loosen all screws with a Phillips screw-; Shown Actual Size

3 Assembled Parts 2 Bases Footrest 2 Frames Hinge Rod 2 Seat Bottom Tubes Pad Seat Bottom Seat Back Base Tray Food Tray Teether Toy Note: Tighten or loosen all screws with a Phillips screw- driver. Do not over-tighten the screws. Shown Actual Size #8 x 1,9 cm Screws – 8 #10 x 2,2 cm Black Screw – 7

Page 4 - Assembly; • Slide a seat bottom tube through each set of plastic rings on; Before assembly and each use, inspect this prod-

4 1 • Place the seat bottom face down on a flat surface.• At an angle, fit the footrest on the seat bottom, as shown. Assembly Seat Bottom Footrest • Slide a seat bottom tube through each set of plastic rings on the seat bottom. 2 Plastic Rings Seat Bottom Tubes Plastic Rings IMPORTANT! Before assem...

Page 5 - black

5 Assembly 4 • Insert two #10 x 2,2 cm black screws through the footrest and into the seat bottom. Tighten the screws. This may require extra force. Insert Screws Here 5 Seat Back Pin Slot • Turn the seat bottom assembly upright.• Fit the seat back pins into the slots in the top side of the seat bot...

Page 8 - • Push each seat height adjuster to be sure they are completely on; PRESS; • Fit the pocket on the top of the pad onto the seat back.

8 Assembly 12 • Push each seat height adjuster to be sure they are completely on the seat bottom tubes. • Insert a #8 x 1,9 cm screw through each seat height adjuster and the ends of the seat bottom tube. Tighten the screws. This may require extra force. Seat Bottom Tube Ends PRESS 13 • Squeeze the ...

Page 9 - Do not unbuckle the restraint system. It is easier to attach or

9 Assembly 16 Clips • Fit the clips on the front edge of the pad onto the seat bottom.• Hook the elastic loops on each side of the pad onto the tabs in the seat back. Shoulder Straps Up Crotch Strap Down Lowest Slot Hint: Do not unbuckle the restraint system. It is easier to attach or re-attach it t...

Page 10 - Smaller Baby; Larger Baby

10 Assembly Smaller Baby • Insert the ends of the shoulder straps through the lower slots in the pad. • From behind the product, attach the ends of the shoulder straps to the peg. 18 Shoulder Straps Larger Baby • From the front of the product, insert the ends of the shoulder straps through the upper...

Page 11 - The child should at all; Secure Child; To tighten the waist straps:; TIGHTEN; To loosen the waist straps:; LOOSEN

11 Prevent serious injury or death from falls or sliding out: The child should at all times wear a safety harness correctly fitted and adjusted. The tray is not designed to hold the child in the chair. WARNING Secure Child 1 • Place your child in the seat. Position the crotch belt between your child...

Page 12 - To change strap slots:

12 4 To change strap slots: • From behind the product, squeeze the restraint release tabs and remove the shoulder straps. • From the front of the high chair, pull the shoulder portions of the restraint system out and then fit them back through the desired shoulder strap slots in the seat pad and in ...

Page 13 - Using the Trays; contact food. The base tray is not dishwasher safe.

13 Using the Trays 6 Base Tray Armrest • Fit the base tray onto the seat armrests. Push down until the base tray "snaps" into place. Hint: Before use, thorougly wash all parts (the trays) that may contact food. The base tray is not dishwasher safe. • While pushing the release bar on the fron...

Page 14 - Using the Teether Toy; • Fit the food tray into the base tray, as shown.

14 Teether Toy Tab Slot Tab • Insert and “snap” the teether toy tab into either slot in the tray. Hint: To remove the teether toy, press the tab and lift the toy. 10 Using the Teether Toy • Fit the food tray into the base tray, as shown. Hint: Before use, thorougly wash all parts (the trays) that ma...

Page 15 - Adjusting the Seat; To adjust the seat angle:; Adjust the seat angle to any of three positions: Upright,; Adjust the seat height to any of seven positions!; It is recommended

15 Adjusting the Seat To adjust the seat angle: • Squeeze the seat back handle and push the seat back forward or, pull it backwards to the desired position. • Push the seat back to be sure it is latched in position. Semi-Recline Upright Recline Hint: Adjust the seat angle to any of three positions: ...