Fisher-Price H7182 - Manuals

Page 2 - WARNING; This product contains small parts in its unassembled state.; Prevent serious injury or death from falls or sliding out:; The tray is not designed to hold the child in the chair.; CAUTION; Warning and Caution; Australia

WARNING This product contains small parts in its unassembled state. Adult assembly is required. Prevent serious injury or death from falls or sliding out: • The child should at all times wear a safety harness correctly fitted and adjusted. The tray is not designed to hold the child in the chair. • A...

Page 3 - Note: Tighten and loosen all screws with a Phillips; Parts

Pad Food Tray 2 Teether Toys Seat Back Frame Seat Bottom Frame Hinge Rod 2 Seat Bottom Tubes 2 Screw Retainers Screw Retainer Screw Retainer Base Tray Footrest Front Base Back Base #10 x 2.2 cm Black Screw #10 x 2.2 cm Black Screws - 2 #10 x 2.2 cm Black Screws - 2 #10 x 2.2 cm Black Screws - 2 #10 ...

Page 4 - Assembly

4 3 • Slide a seat bottom tube through each set of plastic rings on the seat bottom. 2 • Place the seat bottom face down on a flat surface.• At an angle, fit the footrest on the seat bottom, as shown. Assembly Plastic Rings Footrest Seat Bottom IMPORTANT! Before each use, inspect this product for da...

Page 5 - black

5 5 Assembly 5 Insert Screws Here Footrest • Insert two #10 x 2.2 cm black screws through the footrest and into the seat bottom. Tighten the screws. #10 x 2.2 cm Black Screw - 2 6 • Turn the seat bottom assembly upright.• Fit the seat back pins into the openings in the top side of the seat bottom as...

Page 8 - Back and Bottom View

8 8 8 Assembly Back and Bottom View Seat Bottom Tube Ends 14 Seat Height Adjusters • From the back and bottom of the assembly, insert a #8 x 1.9 cm screw through both seat height adjusters and the ends of theseat bottom tube. Tighten the screws. #8 x 1.9 cm Screw - 2 15 Back and Bottom View Hole Pad...

Page 9 - and; Back View

9 Assembly Shoulder Portion 16 • Insert the crotch belt through the slot in the pad. Make sure the crotch belt is not twisted. • Fold the top of the pad down. • Remove the shoulder portion of the waist/shoulder belts by feeding them through the slots in the seat back. 17 • Lift the top of the pad. •...

Page 10 - Battery Installation; alkaline

10 Battery Installation 1.5V x 3 "AA" (LR6) Battery Compartment Shown Actual Size • Loosen the screws in the battery compartment. Remove the battery compartment door. • Insert three “AA” (LR6) alkaline batteries. • Replace the battery compartment door and tighten the screws. Hint: We recomme...

Page 11 - Securing Your Child; The child should at all; Tighten; To tighten the waist belts:; Loosen; To loosen the waist belts:

11 11 Securing Your Child IMPORTANT! Before each use, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT useif any parts are missing or broken. Contact Mattel for replace-ment parts and instructions if needed. Never substitute parts.Place the high chair on ...

Page 12 - To tighten the shoulder belts:; To change shoulder belt slots:

12 12 Securing Your Child 4 • To tighten the shoulder belts: Hold the adjuster and pull the front shoulder strap down. • To loosen the shoulder belts: Slide the adjuster down. Note: After adjusting the restraint system to fit your child, make sure you pull on it to be sure it is securely fastened. S...

Page 13 - Using the Trays and Toys

13 Prevent serious injury or death fromfalls or sliding out. The child should at all times wear a safety harness correctly fittedand adjusted. The tray is not designed tohold the child in the chair. WARNING 7 • Fit the base tray onto the seat armrests. Push down until the base tray "snaps" i...

Page 14 - “snap”

14 11 Release Bar Base Tray • While pushing the release bar on the front of the base tray, pull the tray base towards you and remove. • Insert the tab on the edge of the electronic toy into the groove in the front of the base tray. • Push the electronic toy down to secure in place. Hint: The electro...

Page 15 - It is recommended; To adjust the seat height:; To adjust the seat angle:; Storage; • Always leave wheels locked

15 Prevent serious injury or death fromfalls or sliding out. It is recommended that the high chair be used in the uprightposition only by children capable of sittingupright unassisted. WARNING Hint: Adjust the seat height to any of seven positions! 16 To adjust the seat height: • Press the levers on...

Page 16 - Care

Storage Storage 19 Base Tray • Fit the holes on the base tray latches onto the pegs on the back of the high chair frame. • Fit the electronic toy to the tab on the back of the high chair, as shown. Peg Hole 20 Pull Frame Release Latch • With the legs all the way open, lower the seat to position 7 th...