Fisher & Paykel V3 DD603 - Manuals

Page 2 - SINGLE MODELS; PARTS SUPPLIED; DOUBLE MODELS; TOOLS NEEDED; INSTALLATION PREPARATION; ELECTRICAL PREPARATION; C) Refer to Page 9, Step 5 for electrical connection options.; PLUMBING & DRAINAGE PREPARATION; E) This Dishwasher’s maximum drain height is 37; CAVITY PREPARATION; ELECTRICAL INFORMATION; POWER SUPPLY CORD

BEFORE YOU START - DOUBLE & SINGLE MODELS PARTS SUPPLIED DOUBLE MODELS Drain Hose Support (1) Drain Hose Joiner (1) Wire Clips (2) Installation Tabs (2) Phillips 16mm Screws (7) Prefinished Toe Kick (1) White prefinished toe kick kit p/n 526678or Black prefinished toe kick kit p/n 526679or Iridi...

Page 3 - SERVICES SPECIFICATIONS; Prefinished & Flat Door 30; THE CAVITY; NN; ” and

DOUBLE MODELS SERVICES SPECIFICATIONS TOE KICK DEPTH Prefinished & Flat Door 2”-4 3 / 8 ” (50-110mm); Integrated 5” (127mm) less the Toe Kick Panel thickness. Minimum Panel thickness using the supplied screws is 3 / 8 ” (9mm). # DOOR FRONT HEIGHT Prefinished & Flat Door 30 5 / 64 ” (764mm); ...

Page 4 - DOUBLE; PLUMBING OPTIONS; OPTION 1; DishDrawer® and Standpipe Ø1; OPTION 2; DishDrawer® with Waste Disposal.; OPTION 3; DishDrawer® using Air Break with Drain Hose Joiner.

MAX height t o t op of AIR BREAK (c ount er to p or wall-mount ed) 37 3 / 8 ” (950mm) DOUBLE MODELS PLUMBING OPTIONS OPTION 1 DishDrawer® and Standpipe Ø1 1 / 2 ” (38mm) with Air Gap. OPTION 2 DishDrawer® with Waste Disposal. 29 1 / 2 ” - 34 3 / 4 ” (750mm - 882.5mm) OPTION 3 DishDrawer® using Air B...

Page 5 - ” and Ø; w NN

WATER CONNECTION Recommended HOT (Maximum 140°F/60°C). Supplied hose to suit 3 / 8 ”(9mm) male compression fitting. WATER SOFTENER MODELS Refer to your DishDrawer® User Guide for how to set up your water softener. WATER PRESSURE DRAIN CONNECTION Drain Hose Joiner to suit Ø 3 / 4 ” ± 5 / 64 ” and Ø 5...

Page 6 - DishDrawer®; Drains will need to be separated to satisfy Kosher; DishDrawer®

SINGLE MODELS OPTION 1 DishDrawer® and Standpipe Ø1 1 / 2 ” (38mm) with Air Gap. OPTION 2 DishDrawer® with Waste Disposal. MAX height t o t op of AIR BREAK (c ount er to p or wall-mount ed) 37 3 / 8 ” (950mm) v v MMMM v v MMMM 6 PLUMBING OPTIONS R NOTE: Prefinished Model is shown. There is no variat...

Page 7 - Optional Flexible Extrusion; INSTALLATION INSTRUCTIONS; MOVING THE PRODUCT INTO THE CAVITY

PLEASE NOTE: Your model of DishDrawer® may differ from the model shown in the installation diagrams. Installation is similar for all models for either Single or Double models. Information referring to Single models only is highlighted in blue. Installation diagrams have been simplified to enable cle...

Page 8 - The product must be levelled to within; SECURING THE PRODUCT

SINGLE MODELS ONLY Check the position of the chassis is still where marked on the cavity, before securing the product. There are four 5 / 8 ” (16mm) round holes, two on the left and two on the right hand side in the sound insulation. These provide access to the mounting tabs. To secure the product t...

Page 9 - ELECTRICAL CONNECTION; Be sure the tub clips on both sides are reset.; REFITTING THE TUB; This must only be done by a certified person.

R INSTALLATION INSTRUCTIONS STEP 5: ELECTRICAL CONNECTION To refit the tub, make sure both of the latches at the rear of each drawer runner are facing forward. Ensure hoses are hooping upward. Place the tub on the half open drawer runners and close the drawer. Important! Before refitting the tub, be...

Page 10 - NOTE: SINGLE MODELS DO NOT HAVE A TOE KICK TO; DO NOT cut the inlet hose.; TIP - Turn the water valve ON to check for any leaks.; CONNECTING THE INLET HOSE

Attach the Drain Hose Support to the cabinetry (with the screw supplied) to prevent siphoning and to keep the drain hose(s) from kinking. If required, the Drain Hose(s) may be trimmed to a suitable length. 29 1 / 2 ” - 34 3 / 4 ” (750mm - 882.5mm) 29 1 / 2 ” - 34 3 / 4 ” (750mm - 882.5mm) DishDrawer...

Page 11 - MEASURING THE TOE KICK

On the chosen groove cut down the vertical ribs at the centre and the ends using a knife. Cut along full length with a knife. Turn Toe Kick over, bend and then cut from front. Sand or scrape bottom edge to remove rough patches. Important! Before cutting ensure the Toe Kick is positioned on a wooden ...

Page 12 - Repeat for each Drawer.; TROUBLE SHOOTING; PHONE TOLL FREE; FITTING THE TOE KICK TO THE PRODUCT; Note: Clearance between Toe Kick and floor must be; FINAL CHECKLIST

R INSTALLATION INSTRUCTIONS Be sure product is level, securely fastened to the cabinetry and opens and closes freely. The DishDrawer® must be free to close with no resistance from the cabinetry. Be sure the inlet hose to valve connection is tightened a further half turn after seal contact. Be sure a...

Fisher & Paykel V3 DD603 - Manuals

Manuals:

Manual Fisher & Paykel V3 DD603

Summary

Fisher & Paykel Manuals