Fisher & Paykel DD605 - Manuals

599464 8 3 DIAGNOSTICS 3.1 DishDrawer™ Diagnostics Dishwasher Diagnostics can only be entered in Power Off mode, i.e. when there is no display on the LCD or the badge LED’s are off. Diagnostics is entered by holding the KEYLOCK and START/PAUSE buttons simultaneously for 5 seconds. Ensure that KEYLOC...

599464 9 3.5 Hardware Output Diagnostic Test Mode This level tests all the hardware outputs and inputs. The LCD display shows “HO”. Press POWER to skip hardware diagnostics and advance to the next level. Press START/PAUSE to enter hardware diagnostics. Once hardware diagnostics has been entered, the...

599464 13 3.8 Temperature & Voltage Display Mode (Not available on integrated or flat door models) During a wash cycle, the current water temperature or the power supply rail voltage of the controller can be displayed on the LCD instead of the time remaining. To enter temperature/voltage display...

599464 14 The DishDrawer™ is still in the Showroom wash mode however, and it can be re-run by pressing POWER and then START/PAUSE. Once show off/showroom wash mode has been initiated, the mains power must be removed to exit out. 3.10 Playing Tunes Once in showroom mode, pressing the START/PAUSE butt...

599464 15 4.2 Hardware Output Test Mode Press and hold KEYLOCK, then START/PAUSE for 5 seconds. All LEDs & LCD segments except Keylock are illuminated. Press POWER once. “HO” will show in the display (integrated and flat door models: Heavy, Normal, Fast, Delicate, Rinse LEDs showing). Press STAR...

599464 16 4.3 Fast Test Cycle Press and hold KEYLOCK, then START/PAUSE for 5 seconds. All LEDs & LCD segments except Keylock are illuminated. Press POWER twice. “FC” will show in the display (integrated and flat door models: Heavy, Normal, Delicate, Rinse LEDs showing). Press START/PAUSE twice. ...

599464 17 4.6 Fault Codes There are 10 F (fatal) faults, which are displayed in the LCD along with the symbol of a spanner (not on integrated or flat door models). A fatal fault will usually require the assistance of a qualified service person. In addition, there are 4 U (user) faults. U1 indicates ...

599464 18 Once the fault has been cleared for an F3, F8 or F9 fault, the power needs to be disconnected and reconnected to reset the isolation relay before the product can be used again. 4.7 Fault Code Description Chart The following chart is a quick reference guide on fault codes. To read a fault c...

599464 22 4.8 Fault Code Problem Solving Charts The following charts can be used as a guide to help locate faults in a DishDrawer™. F1 Flood Detected The bottom controller flood detector circuit has been activated. The product will abort the wash program, log the fault, start the drain pump, and rep...

599464 23 F2 Motor Not Rotating The controller has not sensed the motor rotating. The product will pause the wash program, log the fault, and report to the user. PRIMARY ACTION - Check the rotor is free to turn. - Check that power is available at controller (e.g. do the lid actuators run in diagnost...

599464 24 F3 Water Temperature Measurement Exceeds 85 Degrees Celsius The water temperature is sensed at greater than 85 degrees C / 185 degrees F. The product will abort the wash program, log the fault, report to the user, and disable the power supply. Note: The isolation relay will be disabled. Po...

599464 25 F4 Element Has Been On Too Long (About 4 Hours) And Water Has Not Reached Required Temperature The element has been on too long (about 3 hours) and the water has not reached the required temperature. The product will abort the wash program, log the fault and report to the user. PRIMARY ACT...

599464 26 F6 Lid Motors Ran But Did Not Reach Stall Current Lid actuators ran but did not reach stall current. The product will pause the wash program, log the fault and report to the user. PRIMARY ACTION - Check that the lid actuators are properly connected to the yokes and the slide mounting brack...

599464 28 F9 Power Supply/Controller Fault Power supply/controller fault. The product will disable power supply, log the fault, lock out the user and report to the user. Note: The isolation relay will be disabled. Power to the product will need to be disconnected then reconnected for it to become fu...

599464 30 U2 Restricted Lid Travel Restricted lid travel. The lid has reached its stall current too soon. The product will retry the lid 3 times, log the fault if the retries fail, then report to the user. PRIMARY ACTION - Check dishes, cutlery or cups are not projecting above the top of the tub. SE...

599464 36 To check that the amount spray leakage is appropriate:- Fill the salt reservoir with water. • In diagnostics mode, turn on the fill water valve and the motor drain. Water will flow out of the dispenser into the tub, as well as out of the water softener overflow into the tub. • Observe the ...

599464 38 5 WIRING DIAGRAM 5.1 Power Distribution Concept Heater Plate Isolation relay Auxillary PSU Mains main PSU Output Drivers dispenser, water softener, drying fan, LEDs Fill valve +Lid Motors 24V 0V Relay control 5 v reg Beeper Tub Home sensor W ash/drain motor bridge sensors (temperature,curr...