Fisher & Paykel CG604DWFCX1 - Manuals

4 Safety and warnings Safety and warnings WARNING! WARNING! Hot Surface Hazard This appliance becomes hot during use.Do not touch the cooktop components, burners, trivets, pan supports or the base when hot.Before cleaning, turn the burners off and make sure the whole cooktop is cool. Failure to foll...

5 Safety and warnings Important safety instructions! Operation Keep children away from the cooktop when it is in use. Household appliances are not intended to be played with by children. Children, or persons with a disability which limits their ability to use the appliance, should have a responsible...

6 Installation instructions A B C D E F G H I J Cooktop and cutout dimensions (mm) C G604 C G905DWFC C G905DW A C A overall width of cooktop 578 914 914 B overall depth of cooktop 511 533 546 C height of chassis below top of bench 50 50 76 D width of chassis 554 840 855 E depth of chassis 480 480 47...

7 Installation instructions Clearances (mm) C G604 C G905DWFC C G905DW A C A minimum clearance from left edge of cutout to: nearest combustible surface 140 140 100 B minimum clearance from right edge of cutout to: nearest combustible surface 140 140 100 C minimum clearance from rear edge of cutout t...

8 Installation instructions Before you start Before starting to install the cooktop, make sure that: the cooktop has not been damaged during transport. In case of doubt after unpacking and checking it, contact the retailer the local distribution conditions (nature of gas and pressure) and the adjust...

9 Installation instructions Fastening the cooktop to the bench This cooktop is suppled with fastening brackets (and screws) that will cope with abench thickness of 20-50 mm. For benches thicker than 50 mm, recess the undersideto a thickness of 20-50 mm. Connecting the cooktop to the gas supply Impor...

10 Installation instructions Special requirements for CG604 and CG905DWFC models Gas connection to these cooktops MUST use the elbow supplied. The regulator will not seal if installed without it. Ensure the fibre washer (supplied) is located between the elbow (supplied) and cooktop gas inlet (Fig.2)...

11 Installation instructions Leak-testing and flame-testing the cooktop Important! The operation of the cooktop, including the ignition system, must be tested before installation is complete. If, after following the instructions below, satisfactory performance cannot be obtained, contact the local g...

12 Installation instructions Converting to a different gas type Important! Gas conversion may only be carried out by a suitably qualified person. To convert from one gas type to another, you need to replace the injectors and adjust the minimum burner setting. To replace the injectors, you will need ...

13 Installation instructions Adjusting the minimum burner setting This has been adjusted at the factory for Natural Gas but may need adjusting for local conditions. When converting to LPG, the minimum setting MUST be re-adjusted for each burner. To adjust the minimum setting, you will need a Ø 2.5 x...

14 Installation instructions Gas rate and injector size table NATURAL GAS LPG Test point pressure (kPa) 1.0 2.75 Burners Injector orifice size (mm) Nominal gas rate (MJ/h@1kPa) Injector orifice size (mm) Nominal gas rate (MJ/[email protected]) CG604LC, CG604CWC, CG604DWFC, CG905DWFC Auxiliary (right...

15 Final checklist TO BE COMPLETED BY THE INSTALLER Have you securely fastened the cooktop to the bench with the supplied brackets? All models except CG905DWAC: Have you used the supplied elbow and fibre washer to connect the gas to the inlet on the cooktop? Have you leak-tested all connections? Are...

16 Introduction About your new cooktop Thank you for buying a Fisher & Paykel gas cooktop. Once it is installed and ready to use, you will want to know everything about it to make sure you get excellent results right from the start.We recommend you read the whole guide before using your new cook...

17 Control dials The dials control the flow of gas through the valve. Using the burners Models with auto-reignition (CG905DWAC) 1 Press the selected burner’s dial down gently and turn it anti-clockwise to HIGH. The ignitors on all the burners will spark. You do not need to hold the dial down. 2 Adju...

18 Using your cooktop If a burner does not light Turn the control dial to O (OFF) and wait at least 1 minute before trying again. Thisis to allow the gas to disperse. If after trying again the burner still does not light, check that: the cooktop is plugged in and the power supply is switched on ther...

19 Using your cooktop If there is a power failure Models with auto-reignition (CG905DWAC) The gas supply will be cut off, even if a burner is in use. The cooktop cannot be used if there is a power failure. Wait until power is restored. If a control dial is still turned on when the power is restored,...

20 Cooking guidelines and cookware Cooking guidelines Important! Never leave the cooktop unattended when in use. Boilover causes smoking and greasy spills that may ignite. Take care when deep-frying: oil or fat can overheat very quickly, particularly on a high setting. Start cooking on a high settin...

21 Cooking guidelines and cookware Using a wok – models with wok burner Use your wok only on a wok burner. On CG604CWC, CG604DWFC, and CG905DWFC models, a wok must always be used with the wok stand supplied. See Fig.18. The centre pan support of CG905DWAC models is shaped to take a traditional wok w...

22 Care and cleaning What? How often? How? Important! Stainless steel base After every use 1 Soak any stubborn stains under a hot soapy cloth. 2 Wipe the soiling off with a cloth using a mild household detergent or stainless steel cleaner. 3 Wipe with a clean damp cloth. 4 Wipe the surface dry with ...

24 Care and cleaning Replacing the pan supports correctly CG905 models The wok support goes in the centre, over the wok burner. The other two pan supports areinterchangeable, but need to be rotated to match the rounded corners of the cooktop base. CG604 models The pan supports are interchangeable, b...

25 Care and cleaning Replacing the burner parts correctly Semi-rapid, rapid, and auxiliary burners Wok burner with cast iron cap and ring (CG604 and CG905DWFC models) Fit the flame spreader to the housing as shown by the arrow in Fig.22 following. Make sure the burner is not able to rotate. Fig.21 C...

27 Troubleshooting Problem Possible solutions A burner does not light. Check that the power to the cooktop is switched on at the wall and there is no power failure. Check the gas supply valve is turned on and the supply to the house is working. You should hear the gas when you turn a burner on. If y...

29 Warranty and service Before you call for service or assistance ... Check the things you can do yourself. Refer to the installation instructions and your user guide and check that: 1 Your product is correctly installed. 2 You are familiar with its normal operation. If after checking these points y...