Fender SR-6520PD - Manuals - manualsarea.com

Page 2 - TABLE OF CONTENTS; SETUP AND OPERATION

TABLE OF CONTENTS 1. OVERVIEW 1-1. BLOCK DIAGRAM1-2. INTRODUCTION 2. FRONT PANEL CONTROLS, JACKS, AND LEDS 2-1. INPUT JACKS 2-1-1. LINE INPUTS2-1-2. MICROPHONE INPUTS 2-2. CHANNEL CONTROLS 2-2-1. CHANNEL MAIN CONTROL2-2-2. CHANNEL TONE CONTROLS2-2-3. EFF./REV. CONTROL2-2-4. MONITOR CONTROL 2-3. MAST...

Page 3 - Signal path typical

Signal path exclusive of individual channel Signal path typical for each channel MICROPHONE LINE HIGH LOW MAIN MON. EFF./REV. TO MAIN BUSS TO EFFECTS/ REVERB BUSS TO MONITOR BUSS MONIT OR EFFECTS/REVERB MAIN MAIN MASTER MAIN OUTPUT GEQ INPUT POWER AMP SPEAKER OUTPUT 2 OHM MINIMUM EFFECTSOUTPUT REVER...

Page 4 - The SR series mixers include DELTACOMP; tive compression system. DELTACOMP

1. OVERVIEW. 1-2. INTRODUCTION. The SR series integrated mixer/amplifiers have beendesigned for easy setup and simple but versatile oper-ation. Requiring only the addition of microphones andspeakers, the SR powered mixers are self-containedsound reinforcement systems, with features and per-formance ...

Page 6 - REAR PANEL

channel is turned all the way down - otherwise a feed-back loop will exist which could cause oscillation andpossible damage to speakers. Care must be taken toinsure that the amplitude of the return signal is not toogreat for the preamp channel input. An input padmay be used if needed. REVERB FOOTSWI...

Page 8 - UPKEEP AND SERVICE

4. Slowly attenuate the Equalizer control which hasthe greatest effect on reducing the ringing. This willtake some trial and error - the first ringing usuallyoccurs between 1 kHz and 4 kHz. Continue until theringing has stopped. 5. Again, slowly increase the output level control untilthe system is o...

Page 9 - POWER AMPLIFICATION SECTION:; PHYSICAL SPECIFICATIONS:; THIS EQUIPMENT MUST BE EARTH GROUNDED.

7. SPECIFICATIONS SR-6520PD / SR-8520PD Part Number: 100V Version: 071-6521-270 / 071-8521-270 120V Version: 071-6521-200 / 071-8521-200 230V Version: 071-6521-260 / 071-8521-260 230V Version: 071-6521-240 / 071-8521-240 U.K. 240V Version: 071-6521-230 / 071-8521-230 AUST. Type Specification: SR-652...

Page 10 - DSP POWERED MIXER; DIGITAL REVERB and EFFECTS; CHANNEL CONTROLS; FRONT P

SR6520PD MAIN OUTPUT MONITOR OUTPUT EFF . OUTPUT REVERB FOOTSWITCH GEQ OUTPUT GEQ INPUT PWR. AMP INPUT SYSTEM P A TCH BA Y PHANTOM POWER OFF ON 12 12 9 9 6 6 3 3 0 0 3 3 6 6 9 9 12 12 -dB -dB +dB +dB 63 125 250 500 1K 2K 4K 8K 16K GRAPHIC EQUALIZER DSP POWERED MIXER AUX. INPUT SPECIAL EFFECTS REVERS...

Page 11 - FIGURE 1

FENDER MAIN P.A. SPEAKERS FIGURE 1 SPEAKER OUT MONITOROUT GRAPHIC EQUALIZER FENDER MODEL M-300 STAGE MONITOR AMPLIFIER FENDER MONITORS (MODEL 1272A, 1275A, 1282 Mk. II, OR 1285 Mk. II). KEYBOARD MICROPHONES MAX. EFF./REV. 00 +15 HIGH -15 +15 LOW -15 MAX. MON. 00 MICROPHONE LINE 3 MAX. EFF./REV. 00 +...

Page 12 - Cabinet A Impedance; FIGURE 4

FIGURE 2 *Example- The length of speaker wire required is between 25 and 50 feet and the speaker impedance is 8 ohms. The minimum recommended gauge speaker wire is 16 gauge. 100'-UP 8 10 12 14 50'-100' 10 12 14 16 *25'-50' 12 14 *16 18 10'-25' 14 16 18 18 0'-10' 16 18 18 18 2 Ω 4 Ω *8 Ω 16 Ω Speaker...

Page 13 - FIGURE 5; total

FIGURE 5 FENDER SPL 6000 ORSPL 9000 POWER AMPLIFIER SPEAKER OUT MAIN OUT AN ILUSTRATION USING AN AUXILIARY POWER AMP AND ADDITIONAL SPEAKERS ON THE MAINS FOR MORE POWER, AND THE BUILT IN SR POWER AMP TO POWER UP TO 4 STAGE MONITOR LOUDSPEAKERS. BUILT IN GEQ NOW WORKS ON MONITORS. 8 Ω 8 Ω 4 Ω total 8...

Page 14 - FIGURE 6; PATCHING AN EFFECT BETWEEN THE EFFECTS OUT AND THE AUX. IN.; EFFECTS OUT; FIGURE 7; PATCHING AN EFFECT BETWEEN THE EFFECTS OUT AND CHANNEL INPUT.; INPUT; EFFECTS

FIGURE 6 PATCHING AN EFFECT BETWEEN THE EFFECTS OUT AND THE AUX. IN. EFFECTS EFFECTS OUT AUX. IN FIGURE 7 PATCHING AN EFFECT BETWEEN THE EFFECTS OUT AND CHANNEL INPUT. CHANNEL INPUT EFFECTS OUT IMPORTANT: EFFECTS/REVERB TURNED ALL THE WAY DOWN (OFF). INPUT OUTPUT INPUT OUTPUT EFFECTS MAX. EFF./REV. ...