Extron XTP T UWP 202 - Manuals

Page 2 - Instrucciones de seguridad • Español; 注意; 注意; Safety Instructions

Safety Instructions • English WARNING: This symbol, , when used on the product, is intended to alert the user of the presence of uninsulated dangerous voltage within the product’s enclosure that may present a risk of electric shock. ATTENTION: This symbol, , when used on the product, is intended to ...

FCC Class A Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. The Class A limits provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equ...

Page 4 - Conventions Used in this Guide; Notifications; may; Software Commands; CE; File; Specifications Availability

Conventions Used in this Guide Notifications The following notifications are used in this guide: WARNING: A warning indicates a situation that has the potential to result in death or severe injury. CAUTION: A caution indicates a situation that may result in minor injury. ATTENTION: Attention indicat...

Page 5 - Contents; SIS Configuration and Control; Command and Response Tables for SIS; XTP System Configuration Software; Installing the XTP System Configuration; Reference Information; XTP T UWP 202 Wallplate Transmitter • Contents

Contents SIS Configuration and Control ..................... 18 Host Device Connection ................................... 18SIS Programming Guide ................................... 18 Host-to-Device and Device-to-Host Communication ........................................... 18 Device-Initiated Me...

Page 7 - XTP T UWP 202 Wallplate Transmitter • Introduction; Introduction; About this Guide; on

XTP T UWP 202 Wallplate Transmitter • Introduction 1 Introduction This section contains general information about this guide and the Extron XTP T UWP 202 Wallplate Transmitter, and selected device features. Topics in this section include: • About this Guide • About the XTP T UWP 202 • Key Features A...

Page 8 - Extron; Key Features

XTP T UWP 202 Wallplate Transmitter • Introduction 2 Figure 1 shows a typical point-to-point application of the XTP T UWP 202 with two input sources. PWR HDC P HD MI HDMI IN LAN VGA RESET CON FIG AU DIO CL IP AUTO SWITCH AUDIO IN VGA IN Extron XTP T UWP 202 Universal XTP Transmitter POW ER 12V HD MI...

Page 10 - XTP T UWP 202 Wallplate Transmitter • Installation and Operation; Installation Overview; Risk of personal injury

XTP T UWP 202 Wallplate Transmitter • Installation and Operation 4 Installation and Operation This section contains information for mounting, connecting, and wiring the XTP T UWP 202. Topics in this section include: • Installation Overview • Installing the Metal Junction Box or Mud Ring • Rear and S...

Page 11 - Installing the Metal Junction Box or Mud Ring; Cutting an Opening in the Mounting Surface

XTP T UWP 202 Wallplate Transmitter • Installation and Operation 5 4. Route and connect cables to the rear and side panel connectors (see Rear and Side Panel Connectors on page 7). 5. Mount the XTP T UWP 202 to the mud ring or metal junction box (see Mounting the XTP T UPW 202 on page 9). 6. Connect...

Page 12 - Installing the Mud Ring; Installing the Mud Ring with Backing Clips; Loosely fasten the mounting backing clip on the end of each screw.; Detail A; Detail B; Backing Clip Installation

XTP T UWP 202 Wallplate Transmitter • Installation and Operation 6 Installing the Mud Ring Backing Clip Mounting Screw Rotate the backing clip out of the way to insert the mud ring into the wall. Figure 2. Installing the Mud Ring with Backing Clips 1. Place 1.25 inches (3.18 cm) long or 0.75 inch (1...

Page 13 - Installing a UL Listed Metal Junction Box; Installing a Metal Junction Box; Rear and Side Panel Connectors; B CD; Rear; Rear Panel Connectors

XTP T UWP 202 Wallplate Transmitter • Installation and Operation 7 Installing a UL Listed Metal Junction Box Metal junction boxes may differ slightly from model to model. Check with the manufacturer for specific installation instructions. ATTENTION: Use metal junction boxes only. Signal Output Cable...

Page 14 - TP Cable Termination and Recommendations

XTP T UWP 202 Wallplate Transmitter • Installation and Operation 8 A XTP output connector — Connect a twisted pair cable to the RJ-45 connector labeled XTP Out on the XTP T UWP 202 and the XTP input port on another XTP device to pass all signals (see TP Cable Termination and Recommendations on page ...

Page 15 - Mounting the XTP T UWP 202; If desired, connect a host device to the front panel Config port (see; SIS Configuration; on page 18 or; Disconnect the host device after configuration is complete.

XTP T UWP 202 Wallplate Transmitter • Installation and Operation 9 Mounting the XTP T UWP 202 NOTE: If desired, connect a host device to the front panel Config port (see figure 8 , E ) before mounting to configure the transmitter (see SIS Configuration and Control on page 18 or XTP System Configurat...

Page 16 - Front Panel Connectors; HDMI input connector

XTP T UWP 202 Wallplate Transmitter • Installation and Operation 10 Front Panel Connectors PWR HDCP HDMI HDMI IN LAN VGA RESET CONFIG AUDIO CLIP AUTO SWITCH AUDIO IN VGA IN A D B CE A HDMI input connector B Analog audio input connector C Analog video input connector D LAN connector (LAN models only)...

Page 17 - Making Connections; HDMI Connection

XTP T UWP 202 Wallplate Transmitter • Installation and Operation 11 Selected Video Input HDMI Embedded Audio Present Analog Audio Present Audio Sent Over XTP VGA N/A Yes Analog audio VGA N/A No No audio HDMI Yes No HDMI embedded audio HDMI Yes Yes HDMI embedded audio HDMI No Yes Analog audio HDMI No...

Page 18 - Use the following pin configurations for twisted pair cables.; Connector; Straight-through Cable; Pin Wire Color; TP Cable Termination; Supported cables; XTP DTP 24 Plug; Package of 10

XTP T UWP 202 Wallplate Transmitter • Installation and Operation 12 TP Cable Termination and Recommendations Use the following pin configurations for twisted pair cables. 1 2 3 4 5 6 7 8 RJ-45 Connector Insert Twisted Pair Wires Pins: Pin 1 2345678 Wire color White-green Green White-orange Blue Whit...

Page 19 - RS-232 and IR Over XTP Communication; RS-232 and IR data can be transmitted or received simultaneously; Wiring the RS-232 and IR Over XTP Connector; The length of exposed wires is critical.

XTP T UWP 202 Wallplate Transmitter • Installation and Operation 13 RS-232 and IR Over XTP Communication The RS-232 and IR Over XTP connector is for pass-through transmission of serial signals, such as projector control signals, and infrared data. To pass bidirectional serial command signals between...

Page 20 - Power Connection; that uses XTP remote power should be routed outdoors.; Local power; SECTION A–A; Power Wiring; The XTP T UWP 202 can be connected to a local power supply.; Electric shock hazard.; The two power cord wires must be kept separate

XTP T UWP 202 Wallplate Transmitter • Installation and Operation 14 Power Connection Apply power to the transmitter locally with the provided power supply or remotely with a power injector or an XTP matrix switcher. ATTENTION: XTP remote power is intended for indoor use only. No part of the network ...

Page 21 - Remote power; Power injector; on page 14) and connect an XTP Power Injector to the XTP; Typical Pont-to-point Application with Remote Power; pair cable with 24 AWG wire.; Direct power from an XTP matrix switcher

XTP T UWP 202 Wallplate Transmitter • Installation and Operation 15 Remote power The XTP T UWP 202 can be powered remotely through an XTP Power Injector or through an XTP matrix switcher. ATTENTION: XTP remote power is intended for indoor use only. No part of the network that uses XTP remote power s...

Page 22 - Operation; contact numbers; Indicators; EDID; EDID Minder

XTP T UWP 202 Wallplate Transmitter • Installation and Operation 16 Operation After all transmitters, all receivers, and their connected devices are powered up, the system is fully operational. If any problems are encountered, verify that the cables are routed and connected properly. If problems per...

Page 23 - Reset Modes; Reset Button (LAN Model Shown without the Decora Faceplate); After a mode 1 reset,

XTP T UWP 202 Wallplate Transmitter • Installation and Operation 17 Reset Modes PWR HDCP HDMI HDMI IN LAN VGA RESET CONFIG AUDIO CLIP AUTO SWITCH AUDIO IN VGA IN A Figure 16. Reset Button (LAN Model Shown without the Decora Faceplate) Use the recessed Reset button on the front panel of the transmitt...

Page 24 - Host Device Connection; Device-Initiated Message; © Copyright; is the firmware version number.

XTP T UWP 202 Wallplate Transmitter • SIS Configuration and Control 18 SIS Configuration and Control The XTP T UWP 202 can be configured and controlled using Extron Simple Instruction Set (SIS) commands or the XTP System Configuration Software (see XTP System Configuration Software on page 23). This...

Page 25 - ASCII to Hex Conversion Table; ASCII to Hexadecimal Conversion; Symbol Definitions

XTP T UWP 202 Wallplate Transmitter • SIS Configuration and Control 19 Error Responses When the XTP T UWP 202 receives an SIS command and determines that it is valid, it performs the command and sends the corresponding response to the host device. If the command is determined invalid or contains inv...

Page 26 - Command and Response Tables for SIS Commands; Input Commands

XTP T UWP 202 Wallplate Transmitter • SIS Configuration and Control 20 Command and Response Tables for SIS Commands Command ASCII Command (Host to Device) Response (Device to Host) Additional Description Input Commands Input selection Select input X! ! In X!] Select input X! . View the selected inpu...

Page 28 - EDID Commands; Advanced Configuration Commands

XTP T UWP 202 Wallplate Transmitter • SIS Configuration and Control 22 Command ASCII Command (Host to Device) Response (Device to Host) Additional Description EDID Commands NOTE: For EDID management, use the XTP System Configuration Software (see EDID Minder on page 34). Advanced Configuration Comma...

Page 29 - Installing the XTP System Configuration Software; Extron Website Download Page; Download

XTP T UWP 202 Wallplate Transmitter • XTP System Configuration Software 23 XTP System Configuration Software This section contains installation and configuration procedures for the XTP System Configuration Software for configuring and controlling the XTP T UWP 202. It can also be controlled with SIS...

Page 30 - Using the XTP System Configuration Software; Connections; Configuration port; on page 11). Ensure the transmitter is connected and; Connections Screen; From the Connections screen in the software, select the; USB; Click the; Connect

XTP T UWP 202 Wallplate Transmitter • XTP System Configuration Software 24 Using the XTP System Configuration Software The XTP T UWP 202 can be controlled directly from the front panel Config port or remotely from an XTP matrix switcher. Connections When opening the XTP System Configuration Software...

Page 31 - Top Menu; File menu; File Menu; Disconnect; Tools Menu

XTP T UWP 202 Wallplate Transmitter • XTP System Configuration Software 25 Top Menu The top menu bar contains three menus for configuring software settings. File menu The File menu contains options for disconnecting from the transmitter and exiting the program. To access the menu, click the File men...

Page 32 - Update Firmware; Downloading Firmware

XTP T UWP 202 Wallplate Transmitter • XTP System Configuration Software 26 Update Firmware This option uploads firmware from the host device to the connected device. NOTE: If necessary, download new firmware from the Extron website (see Downloading Firmware on page 38). 1. From the Tools menu, selec...

Page 33 - Help menu; Help Menu; About the Software; Extron Website

XTP T UWP 202 Wallplate Transmitter • XTP System Configuration Software 27 Help menu The Help menu contains a way to access XTP System Configuration Software information, a link to the help file, and a link to the Extron website. Figure 24. Help Menu NOTE: The Tutorial (System Configuration) option ...

Page 34 - Device Settings; ) on the Global Navigation bar to open the Device Settings screen.; Transmitter Device Settings Screen; AV Controls panel; Input selection; — Click an; Input; button to select an input. As a new

XTP T UWP 202 Wallplate Transmitter • XTP System Configuration Software 28 Device Settings The Device Settings screen allows a user to view and edit various device settings for the device directly connected to the PC running the XTP software. Click the Device Settings icon (see figure 26, 1 ) on the...

Page 35 - — Displays the input name.; Signal Type; — Displays the signal type of each input. Input 1 is; analog; Auto Memory; — Select the; HDCP Authorized; check box to have input 2

XTP T UWP 202 Wallplate Transmitter • XTP System Configuration Software 29 Input/Output tab Click the Input/Output tab (see figure 27, 1 ) to open the Input/Output screen. It contains input information and options to apply automatic settings to individual inputs. Figure 27. Input/Output Tab 2 Input ...

Page 37 - Audio tab; Audio; Audio Tab; Input format panel; Input format; Audio Format; Auto; Analog audio gain; Gain

XTP T UWP 202 Wallplate Transmitter • XTP System Configuration Software 31 Audio tab Click the Audio tab (see figure 29, 1 ) to open the Audio screen. It contains settings for audio input format and analog audio gain. Figure 29. Audio Tab Input format panel 2 Input format — From the Audio Format dro...

Page 38 - General tab; General; General Tab; Auto-input Switching panel; Auto-input Switching; Enable Auto-Input Switching; Factory reset; Factory Reset; ZXXX; System reset

XTP T UWP 202 Wallplate Transmitter • XTP System Configuration Software 32 General tab Click the General tab (see figure 30, 1 ) to open the General screen. It contains settings for auto switch mode and factory reset. Figure 30. General Tab Auto-input Switching panel 2 Auto-input Switching — Click t...

Page 40 - EDID Minder Screen; Assign EDID; To assign EDID to selected inputs:; Assign; To assign EDID to all inputs:; Assign to All

XTP T UWP 202 Wallplate Transmitter • XTP System Configuration Software 34 EDID Minder Use the EDID Minder screen to assign unique EDID to the input or match current output resolutions to the input. Click the EDID Minder icon (see figure 31, 1 ) on the global navigation bar. The EDID Minder screen o...

Page 41 - EDID Minder Filters; Common timings

XTP T UWP 202 Wallplate Transmitter • XTP System Configuration Software 35 Import EDID 1. On the EDID Minder screen, click the Add EDID to Library button (see figure 31, 8 ). The Browse window opens. 2. Select the desired EDID file and click Open . The EDID appears in the Available EDID panel (see f...

Page 42 - XTP T UWP 202 Wallplate Transmitter • Reference Information; Updating Firmware with Firmware Loader; Downloading Extron Firmware Loader; Locating Software on the Extron Website; On the Extron; website; On the left sidebar, click the; Software

XTP T UWP 202 Wallplate Transmitter • Reference Information 36 Reference Information This section contains mounting information and instructions for updating firmware. Topics in this section include: • Updating Firmware with Firmware Loader • Mounting Template Updating Firmware with Firmware Loader ...

Page 43 - Navigating to Firmware Loader; link on the right that corresponds with the program (see; Installing Firmware Loader

XTP T UWP 202 Wallplate Transmitter • Reference Information 37 Figure 34. Navigating to Firmware Loader 3. Click the F link and navigate to Firmware Loader (see figure 34, 3 ). 4. Click the Download link on the right that corresponds with the program (see figure 34, 4 ). 5. Submit any required infor...

Page 44 - Downloading Firmware from the Extron Website; Firmware; Navigate to the XTP T UWP 202.; link to the right of the desired device.

XTP T UWP 202 Wallplate Transmitter • Reference Information 38 Downloading Firmware Figure 35. Downloading Firmware from the Extron Website 1. On the Extron website , click the Download tab (see figure 35, 1 ). 2. On the left sidebar, click the Firmware link (see figure 35, 2 ). 3. Navigate to the X...

Page 45 - Installing Firmware with Firmware Loader; completed

XTP T UWP 202 Wallplate Transmitter • Reference Information 39 Installing Firmware with Firmware Loader Use the Firmware Loader utility to upload firmware to the transmitter when connected directly to the device. 1. Connect the host device to the front panel USB port. 2. Open Firmware Loader and est...

Page 46 - Mounting Template; SURFACE; Please measure the printed template before cutting.; Mounting Template for 2-gang Mud Rings; Measure the template before cutting.

XTP T UWP 202 Wallplate Transmitter • Reference Information 40 Mounting Template Figure 37 is a example of a mounting template for preparing mounting surfaces. It is not to full size. 4.26" (10.83 cm) 4.28" (10.87 cm) Recommendedcut-out areafor the installationsurface. Top Panel SURFACE CUT-...

Page 47 - Contact Information; USA; xtron

Extron Headquarters +1.800.633.9876 (Inside USA/Canada Only)Extron USA - West Extron USA - East +1.714.491.1500 +1.919.850.1000 +1.714.491.1517 FAX +1.919.850.1001 FAX Extron Europe +800.3987.6673 (Inside Europe Only)+31.33.453.4040 +31.33.453.4050 FAX Extron Asia +65.6383.4400+65.6383.4664 FAX Extr...