Extron VLM 1000 - Manuals

VoiceLift Microphone Installation • Introduction — Planning 1-4 Introduction — Planning, cont’d • Optional VLR 102SR Secondary receiver. One or more secondary receivers (VLR 102 SR) may be needed if any of the following conditions exist:  The room is larger than 40' by 40'.  Obstructions exist bet...

1-5 VoiceLift Microphone Installation • Introduction — Inventory Overview Introduction — Inventory Overview VLP 102 Pendant Microphone VLP 102 Pendant MicrophoneVLR 102 IR ReceiverRJ-45 to C/S adapterWall charger/power supplyEthernet cable, 15 ft. VLM 1000 VoiceLift Microphone #42-139-01 VLP 102 Pen...

N For operation and setup of other Extron PoleVault system components mentioned in this guide, refer to the appropriate user manual provided with each product. This overview outlines the basic steps for installing the VLR 102 VoiceLift Receiver. Detailed descriptions with illustrations of these step...

VoiceLift Microphone Installation • Installation — Overview 2-2 Installation — Overview, cont’d Outline of installation steps Stage 1 — Install the VLR 102 Receiver Drop ceiling: c Cut a hole in the ceiling tile. (page 2-4) c Mount the receiver housing to the ceiling tile. (page 2-4) c Attach a cond...

Installation — Stage 1 Receiver housing and back plate Where it goes: The housing attaches to the receiver dome, and the back plate mounts to a ceiling tile or a wall. What it does: Protects the receiver base plate and connectors. The housing contains knockouts for different sizes of raceways, and t...

1. Cut a hole in the ceiling tile. a. Remove the ceiling tile in which the receiver will be installed. b. Determine the hole location, then cut a hole in the ceiling tile 2" to 3.5" in diameter, using a circular saw (shown at right) or other type of saw. (Saws are not included.) N This hole ...

3. Attach a conduit to the back plate if needed. If desired, attach a conduit to the open knockout in the back plate. N Observe all local and national building and safety codes to ensure that the installation meets all regulatory codes. c Attach a conduit to the back plate if desired. 2-5 VoiceLift ...

1. Install the junction box. Install the junction or ceiling box (not included) flush to the surface. Use a one-gang plaster ring (Raco 772) if the junction box is larger than one-gang. 2. Attach the receiver housing to the junction box. a. Align the receiver housing with the junction box. b. Secure...

Installing the Receiver in a Wall or Other Hard Surface 1. Install a raceway if needed. If using a raceway for the cables, install it at the appropriate location on the mounting surface. N Raceway knockouts on the receiver housing fit common types of raceways such as the Wiremold 500/700 series and ...

Stage 2 This stage consists of installing/connecting the items shown below. Ethernet cable CAT 5, 5E, or 6 with T568A or T568B straight through wiring Where it goes: Attaches to the receiver ’s RJ-45 OUT port and to the VoiceLift Adapter ’s RJ-45 port. What it does: Provides power to the receiver an...

Ä Pull the cable(s). 1. Pull the cables to the receiver. a. Pull the communication/power Ethernet cable through the receiver ’s base, along with any other cables that will be attached to the receiver (RS-232, Ethernet cable to a secondary receiver, etc.) b. If mounting to a wall and using a raceway,...

ON 1 2 CTS-2 O N 1 2 CTS-2 MIX TONE RS-232 AUX IN CTC + OUT IN RL Y Tx IN Rx C NO MIX TONE Base Plate Ö Locate the arrow on the housing rim. Ñ Locate the locking tab marked with the arrow. 2. Connect the cables to the receiver (continued) . b. Install any optional devices and connect their cables to...

Stage 3 1. Configure the system. Follow the steps in your PoleVault installation guide to configure the PoleVault system. 2. Set up the microphone. (Refer to the VoiceLift Microphone Setup Guide card, provided with your microphone, for details of these procedures.)a. Set the channels using the rotar...

1. Connect the receiver to the MLC 104 IP Plus. a. Wire one of the provided two-pole captive screw connectors to one end of a communication cable. b. Plug the communication cable into the receiver ’s RLY port. N If the MLC controller and the PoleVault switcher are using separate power supplies, grou...

VoiceLift Microphone Installation • Reference Information 2-18 Reference Information Audio Tone control .................................... On or off, switch selectable Audio input Number/signal type VLR 102............................... 1 infrared from VLM microphones 1 mono, balanced, aux/mix in...

2-19 VoiceLift Microphone Installation • Reference Information General Power .............................................. 12 VDC supplied by an Extron PoleVault ® amplifier or from an optional external power supply via an RJ-45 jack shared with audio output (pin 5 = +12 VDC input, 8 = GND) Power i...

VoiceLift Microphone Installation • Reference Information 2-20 Installation — Reference Information, cont’d Audio/acoustic and electrical Microphone type ........................... Omnidirectional electret condenserMicrophone gain ........................... -6 dB to +6 dB, adjustable in 1 dB steps...

2-21 VoiceLift Microphone Installation • Reference Information Specifications — VLC 102 Microphone Charging Station General External power supply ................. 110 VAC to 130 VAC, 50/60 Hz, external, 2 prong; to 5 VDC, 1 A, regulated 3.5 mm o.d. jack, center positive Power input requirements ......