Extron SW YUV A - Manuals

i SW RGB and YUV A Switchers • Table of Contents Table of Contents Chapter 1 • Introduction ....................................................................................................... 1-1 About the Switchers ...................................................................................

ii SW RGB and YUV A Switchers • Table of Contents Table of Contents, cont’d Chapter 4 • Remote Control ................................................................................................ 4-1 Simple Instruction Set ............................................................................

SW RGB and YUV A Switchers 1 Chapter One Introduction About the Switchers Features

Introduction, cont’d SW RGB and YUV A Switchers • Introduction 1-2 Introduction About the Switchers The Extron SW RGB and YUV A series (figure 1-1) is a family of six RGB videoswitchers and one component video switcher, some with audio, in an array ofinput and output configurations. The models avail...

1-3 SW RGB and YUV A Switchers • Introduction Features Audio switching models Inputs — These switchers input 2, 4, or 6 stereo audio signals, balanced or unbalanced, on 3.5 mm, 5-pole captive screw terminals. Outputs — The selected audio input is buffered and output, balanced or unbalanced, on a 3.5...

Introduction, cont’d SW RGB and YUV A Switchers • Introduction 1-4 All models Bandwidth — Bandwidth is 350 MHz (-3 dB). This high bandwidth allows the switchers to switch all of the high-resolution video signals with no loss ofsignal quality. Input signal sensing — The switcher continuously monitors...

SW RGB and YUV A Switchers 2 Chapter Two Installation Installation Overview Mounting the Switcher Cabling and Rear Panel Views

Installation, cont’d SW RGB and YUV A Switchers • Installation 2-2 Installation Installation Overview Install an SW RGB or SW YUV A Series switcher as follows: 1 Turn off the input and output devices, and unplug their power cables. 2 If desired, mount the switcher in a rack, under furniture, or thro...

2-3 SW RGB and YUV A Switchers • Installation (2) 4-40 x 3/16" Screws Use 2 mounting holes on opposite corners. False front paneluses 2 front holes. RG BH V & AU DIO SW ITC HE R AU TO SW ITC H AC UT IVE SW2 RGBHV A 2 1 AU DIO CO NF/S AVE -d B +dB Figure 2-1 — Rack mounting an SW2 switcher #8...

Installation, cont’d SW RGB and YUV A Switchers • Installation 2-4 Under furniture mounting the switcher The SW2 switcher models can be mounted under a table or other horizontal surfacewith an optional Extron under-desk mounting kit (part #70-077-01). The SW4 andSW6 switcher models can be mounted un...

2-5 SW RGB and YUV A Switchers • Installation 3 . Drill 1/4" (6.4 mm) deep, 3/32" (2 mm) diameter pilot holes in the table ordesk at the marked screw locations from the underside/inside (concealedside) of the furniture, where the switcher will be located. 4 . Insert the four wood screws into...

Installation, cont’d SW RGB and YUV A Switchers • Installation 2-6 5 . Slide the switcher up and down or back and forth in the mounting brackets until the face ofthe switcher is at the desired height. Tighten the screws that secure the bracket in place. If the screws are inaccessible to a screwdrive...

2-7 SW RGB and YUV A Switchers • Installation Inputs 1 RGB and component video inputs — RGB models — For each input, connect an RGBHV, RGBS, RGsB, RsGsBs, or component video source to these BNC connectors. Connect the cables asshown in figure 2-8. SW6 YUV A — For each input, connect a component vide...

Installation, cont’d SW RGB and YUV A Switchers • Installation 2-8 The audio level for each input can be individually set, via the front panel orunder RS-232 control, to ensure that the level on the output does not varyfrom input to input. See chapter 3, Operation, and chapter 4, Remote Controlfor d...

2-9 SW RGB and YUV A Switchers • Installation Remote connection 7 Remote connector — Connect a host device, such as a computer or touch panel control, or a remote contact closure device to the switcher via this9-pin D connector (figure 2-11) for remote control of the switcher. See chapter 4, Remote ...

SW RGB and YUV A Switchers 3 Chapter Three Operation Controls and Indicators Switcher Operations Optimizing the Audio (SW2, SW4, and SW6 RGBHV A only) Troubleshooting — If No Image Appears

Operation, cont’d SW RGB and YUV A Switchers • Operation 3-2 Operation Controls and Indicators The SW RGB or SW YUV A family of switchers have 2, 4, or 6 input buttons andLEDs on the front panel. Audio models also have front panel configurationcontrols and LEDs. All models have an Auto/Manual mode s...

3-3 SW RGB and YUV A Switchers • Operation Audio controls and indicators 3 Audio configuration/save button and LED — The Audio button and LED enable the user to view and/or change the current audio level setting for eachinput. See Audio gain and attenuation in this chapter. 4 Down ( ) button and LED...

Operation, cont’d SW RGB and YUV A Switchers • Operation 3-4 Switcher Operations The following paragraphs detail the power up process and provide sampleprocedures for selecting an input and viewing and adjusting the audio level. Power Plug in the switcher. On all switcher models, power is automatica...

3-5 SW RGB and YUV A Switchers • Operation 2 . Press and hold the Audio Conf/Save button until the Conf/Save LED begins to blink, then release the Conf/Save button. The +dB and –dB LEDs display the polarity (+ or –). The lit+dB LED indicates a positive (gain) level. The lit –dB LEDindicates a negati...

Operation, cont’d SW RGB and YUV A Switchers • Operation 3-6 If the +dB and –dB LED are both lit they indicate 0 dB. Otherwise, you candetermine the exact gain or attenuation using the following procedure. a . If one or more input LEDs are lit AND the +dB LED is/are lit , press and release the butto...

3-7 SW RGB and YUV A Switchers • Operation Audio level reset — single input Reset the audio level for an input to 0 dB as follows: The switcher must be in normal (manual) mode. 1 . Press and release an input button to select an input. 2 . Press and hold the Audio Conf/Save button until the Conf/Save...

Operation, cont’d SW RGB and YUV A Switchers • Operation 3-8 Troubleshooting — If No Image Appears 1 . Ensure that all devices are plugged in and powered on. The switcher isreceiving power if the front panel Power LED (if equipped) is lit. 2 . Ensure an active input is selected on the switcher or th...

SW RGB and YUV A Switchers 4 Chapter Four Remote Control Simple Instruction Set Windows-Based Control Program Contact Closure Infrared Remote Control

Remote Control, cont’d SW RGB and YUV A Switchers • Remote Control 4-2 Remote Control The SW RGB and SW YUV A Series switchers can be remotely controlled via theswitcher ’s rear panel Remote connector (figure 4-1). Remote control devices canbe: • A host device (such as a computer or control system) ...

4-3 SW RGB and YUV A Switchers • Remote Control Switcher-initiated (unsolicited) messages When a local event, such as a front panel operation or error condition, occurs, theswitcher responds by sending a message to the host. The switcher-initiatedmessages are listed below. (C) Copyright 2002, Extron...

Remote Control, cont’d SW RGB and YUV A Switchers • Remote Control 4-4 Command/Response table for SIS commands Command ASCII Command Response Additional description (host to switcher) (switcher to host) Input selection Select video and audio input X1 ! In X1 •All Select input X1 video and audio. Exa...

4-5 SW RGB and YUV A Switchers • Remote Control Command/Response table for SIS commands (Continued) Command ASCII Command Response Additional description (host to switcher) (switcher to host) Input signal sensing Request all inputs’ status 0S Sig• X3 1 • X3 2 •...• X3 n Each X3 response is the signa...

Remote Control, cont’d SW RGB and YUV A Switchers • Remote Control 4-6 Windows-Based Control Program The Universal Switcher Control Program, part #29-031-01, is compatible withMicrosSoft Windows 3.1, 3.11, 95/98, and above, and provides remote control of thefollowing: • Input selection (including au...

4-7 SW RGB and YUV A Switchers • Remote Control Using the help system For information about program features, you can access the help program in any ofthe following ways: • From the Extron Electronics program group, double-click on the Universal Switcher Control Program Help icon. • From within the ...

SW RGB and YUV A Switchers A Appendix A Specifications and Part Numbers Specifications Part Numbers

Specifications, cont’d SW RGB and YUV A Switchers • Specifications and Part Numbers A-2 Specifications Video Gain ............................................... Unity.Bandwidth .................................... 350 MHz (-3 dB)Differential phase error .............. 1.0º at 3.58 MHz and 4.43 MHzD...

A-3 SW RGB and YUV A Switchers • Specifications and Part Numbers Sync Input type ..................................... RGBHV (except SW6 YUV A), RGBS, RGsB, RsGsBsOutput type .................................. RGBHV (except SW6 YUV A), RGBS, RGsB, RsGsBsInput level .....................................

Specifications, cont’d SW RGB and YUV A Switchers • Specifications and Part Numbers A-4 Audio output — SW 2/4/6 RGBHV A only Number/signal type ................... 1 stereo, balanced/unbalancedConnectors .................................... (1) 3.5 mm captive screw connector, 5 poleImpedance ..........

A-5 SW RGB and YUV A Switchers • Specifications and Part Numbers Part Numbers SW RGBHV switcher part numbers Switcher Part # SW2 RGBHV video switcher 60-491-01 SW2 RGBHV A video and audio switcher 60-491-21 SW4 RGBHV video switcher 60-492-01 SW4 RGBHV A video and audio switcher 60-492-21 SW6 RGBHV v...

Specifications, cont’d SW RGB and YUV A Switchers • Specifications and Part Numbers A-6 Plenum BNC-5 Mini HR Cable Part # Plenum BNC-5 Mini HR bulk, 500', 1000' 22-103-02, -03 BNC-5 RC and BNC-6 RC Cable Part # BNC-5 RC bulk, 500', 1000' 22-127-02, -03 Assorted connectors BNC connectors Part # RG6/S...

FCC Class A Notice Note: This equipment has been tested and found to comply with the limits for a Class A digitaldevice, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonableprotection against harmful interference when the equipment is operated in a commercialenvironm...