Extron SI 3 - Manuals - manualsarea.com

Page 2 - SI 3 Speakers • Packaging; Packaging Information; Figure 1 — SI 3 speaker packaging details; Bottom Foam

SI 3 Speakers • Packaging Packaging Information Figure 1 — SI 3 speaker packaging details Part N o. XXX-X XX-01 Insta ll 206 W Ce iling S peake r 33-XX XX-01 REV . Thick Single WallPacking Bottom Foam Speakers(each plasticwrapped) Hex Tool(plastic wrapped) Top Foam Product Label Wall MountAssemblies...

Page 3 - Introduction; SI 3 Speakers • Introduction; About the SI 3 Speakers; The Extron

Introduction SI 3 Speakers • Introduction 1 About the SI 3 Speakers The Extron System INTEGRATOR ™ SI 3 full range, compact, surface mount speaker is ideally suited for classrooms, conference rooms, and boardrooms. With a weather resistant construction, it is also suitable for outdoor environments, ...

Page 4 - SI 3 Speakers • Features; Figure 3 — Speaker features; Features

SI 3 Speakers • Features 2 Features Dimensions : 8.75" H x 5.75" W x 5.61" D (22.2 cm H x 14.6 cm W x 14.24 cm D) a Bass reflex port b Front locking access (allows for speaker position adjustment) c 3" full range driver with paper cone d Grill and enclosure may be painted to match en...

Page 5 - Installation; SI 3 Speakers • Installation; Installing the SI 3 Speakers; If the speakers are to be placed on a horizontal surface such; Figure 4 — Surface speaker application; Desktop or bookshelf applications

Installation 3 SI 3 Speakers • Installation Installing the SI 3 Speakers The Extron SI 3 speakers can be mounted on a surface, such as a wall or post, or mounted in a bookcase, or on a shelf, and can be used with any Extron product supporting audio. N If the speakers are to be placed on a horizontal...

Page 6 - Wall mounting applications; Installing the wall mount assembly; Figure 5 — Rotating and mounting the wall mount; Figure 6 — Mounting holes on the rear plate

4 SI 3 Speakers • Installation Installation, cont’d Wall mounting applications Installing the wall mount assembly N Before starting installation, ensure that the wall and wall material are capable of supporting the combined weight of the speakers and the wall mount assemblies. 1 . If mounting to dry...

Page 7 - Figure 7 — Installing the wall mount assembly

4. Mark the wall where the wire will pass through the plate, and cut a small access hole large enough for the wire to pass through without interference. Where the stud is wider than the plate's access hole, cut the hole in the wall to the left or right and directly alongside the stud (see figure 7)....

Page 8 - Figure 8 — Passing the wire through the plate; Preparing the speaker for mounting

Installation, cont’d 6 SI 3 Speakers • Installation 6 . Pull sufficient wire up through the holes in the rear plate (see figure 8) to allow ease of connection to the speaker after installation. N Do not strip and connect the wire at this time. Pass the wires through the plateaccess hole. Line of Stu...

Page 10 - Wiring the speakers; Extron; Figure 11 — Inserting wiring into the terminals

8 SI 3 Speakers • Installation Installation, cont’d Wiring the speakers 1. When both speakers are in place, carefully pull enough speaker wire to reach to the terminals at the back of the each speaker and strip the ends of the wire approximately 5/8" (15 mm). Twist the bare strands so that they ...

Page 11 - Figure 13 — Adjusting speaker and locking in place; Service Access

5 . Insert the hex tool into the locking access, and slightly loosen the hex cap screw. Adjust the speaker to the desired angle (see figure 13), and torque the hex cap screw down clockwise until snug, about 6 to 8 turns. The speaker remains securely in the desired position. Turn clockwiseto tighten....

Page 12 - SI 3 Speakers • Troubleshooting Tips; To refit the grill; If the speaker makes the grill vibrate and creates unwanted; Troubleshooting Tips

10 SI 3 Speakers • Troubleshooting Tips Troubleshooting Tips To refit the grill : 1 . Carefully press the grill back into place. 2 . Insert and tighten down the screws. 3 . Replace the logo. Securing the grill (optional) N If the speaker makes the grill vibrate and creates unwanted noise when in use...

Page 13 - Action

Observed Problem Possible Cause(s) Remedial Action 1 Speaker easily lifted from mount assembly Locking hex cap screw not tightened enough Following the steps on page 9, tighten the hex cap screw until it is not possible to remove the speaker. 2 No sound heard from speakers Speaker cables not connect...

Page 14 - SI 3 Speakers • Specifications; Audio/acoustic and electrical; 2 W continuous program; General; brackets; Specifications are subject to change without notice.; Specifications

12 SI 3 Speakers • Specifications Audio/acoustic and electrical Speaker type ................................... Indoor/outdoor surface mount speakerFrequency range ............................ 75 Hz to 18 kHz, -10 dB, half space Power capacity .............................. 16 W continuous pink noi...

Page 15 - Extron’s Warranty; will begin the repair process as quickly as possible.

Extron’s Warranty Extron Electronics warrants this product against defects in materials and workmanship for a period of five years from the date of purchase. In the event of malfunction during the warranty period attributable directly to faulty workmanship and/or materials, Extron Electronics will, ...