Extron SF 26X - Manuals - manualsarea.com

Page 2 - Safety Instructions; Safety Instructions • English; Sicherheitsanweisungen • Deutsch; Instrucciones de seguridad • Español; 注意; 注意

Safety Instructions Safety Instructions • English WARNING: This symbol, , when used on the product, is intended to alert the user of the presence of uninsulated dangerous voltage within the product’s enclosure that may present a risk of electric shock. ATTENTION: This symbol, , when used on the prod...

Conventions used in this guide notifications The following notifications are used in this guide: CauTIOn: A caution indicates a situation that may result in minor injury. warnIng: A warning indicates a situation that has the potential to result in death or severe injury. aTTEnTIOn: Attention indicat...

Page 4 - Contents; Introduction; SF 26X User Guide • Contents

Contents Introduction .................................................... 1 About the SF 26X Speaker ................................ 1Features ............................................................. 1Application Example ........................................... 2 Installation ................

Page 5 - About the SF 26X Speaker; SF 26X User Guide • Introduction

Introduction This user guide contains information about the Extron SF 26X Ceiling Mount Speaker. About the SF 26X Speaker The SF 26X speaker is a two-way, low impedance, ceiling-mount speaker system that features an 8 ohm open back speaker with a 6.5 inch woofer and a 3/4 inch tweeter designed for u...

Page 6 - Application Example; SF 26X Application Example

Application Example The illustration below is one example of configuring a system using the SF 26X speakers. L R SIG LINK DTP IN SIG LINK DTP OUT 50/60 Hz 100-240V X.XA MAX 1 2 RGB OUT HDMI MIC MIX RS-232 MPS 602 SA Tx Rx G MUTE HDMI AUDI O PHANTOM POWER SELECT 3 4 5 6 OUTPUTS AMP OUT REMOTE OVER DT...

Page 7 - Installation; Installing the SF 26X in a Suspended Ceiling; Painting the Baffle and Grille

Installation The Installation section describes: • Installing the SF 26X in a Suspended Ceiling • Painting the Baffle and Grille Installing the SF 26X in a Suspended Ceiling 1. Remove power from all devices. NOTE: If the baffle or grille is to be painted, see the Painting the Baffle and Grille secti...

Page 8 - Wire Gauge Table; Strip no more than 3/16; SF 26X User Guide • Installation

6. Attach speaker wires from the ceiling tile hole to the included four-pole captive screw connector using one of the following three methods below. NOTES: • Be sure that the combined impedance of the speaker system does not equal a value less than the rated minimum load impedance of the amplifier. ...

Page 9 - Wiring Multiple Speakers Using Loop-through:; This configuration is useful for troubleshooting in four ways:

• Wiring Multiple Speakers Using Loop-through: A loop-through electrical connection is made on the crossover board of the SF 26X. Connect the wires to the captive screw connectors of the speakers, as shown below. Be sure to tighten the screws. NOTES: • Be sure that the combined impedance of the spea...

Page 11 - Wiring Speakers in Parallel:; Signal Test Points

• Wiring Speakers in Parallel: Connect the wires to the captive screw connectors of the speakers, as shown below. Be sure to tighten the screws. NOTES: • Be sure that the combined impedance of the speaker system does not equal a value less than the rated minimum load impedance of the amplifier. • Wh...

Page 12 - first; disconnect the speaker; Impedance Test Points; Disconnect the speaker system from the amplifier; before; performing this test, otherwise you may damage the test meter.; Wiring a Single Speaker:

To test the impedance of the entire speaker system, first disconnect the speaker wires from the amplifier and then measure the impedance from the disconnected wires, as shown below. Impedance Test Points Captive Screw Connector Test Points + _ _ + To next speaker Red Wire (+) disconnected from Ampli...

Page 13 - Strain Relief Tie Off Point; Do not overtighten the screws.; Mounting the Speaker Using the Four Locking Arms

7. Insert the captive screw connector into the four-pole receptacle on the speaker crossover board as shown below. Zip Tie Captive Screw Connector Strain Relief Tie off Point Figure 3. Strain Relief Tie Off Point 8. Secure the speaker wire to the strain relief tie off point using the included zip ti...

Page 14 - Attaching the Secondary Support Line; Attach the secondary support line.; Do not allow any slack in the secondary support line.; Replace the adjacent ceiling tile.; Pivoting the Tweeter; The tweeter can be pivoted only. Do not attempt to rotate the

10. Attach the secondary support line if required, as shown below. Secondary Support Line Secondary Tie off Point Figure 5. Attaching the Secondary Support Line a. Remove the ceiling tile adjacent to the tile where the speaker is mounted. b. Attach the secondary support line. ATTENTION: Do not allow...

Page 15 - Installing the SF 26X Grille

12. Position the outer perimeter of the grille into the groove of the speaker baffle. Six magnets pull the grille securely into place, as shown below. Speaker Grille Figure 7. Installing the SF 26X Grille NOTE: Grille hooks are provided for removal of the grille after installation. SF 26X User Guide...

Page 16 - Painting the Baffle

Painting the Baffle and Grille NOTE: The cutout template that was used in step 2 of the previous section will be used as a paint shield when painting the outer circumference of the baffle. Painting the Baffle 1. Remove the grille using the provided grille hooks and set the grille aside. 2. Place cut...

Page 17 - Extron Warranty; and Central America:

Extron Headquarters +1.800.633.9876 (Inside USA/Canada Only)Extron USA - West Extron USA - East +1.714.491.1500 +1.919.850.1000 +1.714.491.1517 FAX +1.919.850.1001 FAX Extron Europe +800.3987.6673 (Inside Europe Only)+31.33.453.4040 +31.33.453.4050 FAX Extron Asia +65.6383.4400+65.6383.4664 FAX Extr...