Extron P/2 DA 2 WM/EC - Manuals

Extron P/2 DA 2 WM/EC – Manual in PDF format online.

Manuals:

Manual

Manual Extron P/2 DA 2 WM/EC

Summary

Page 2 - Precautions; Safety Instructions • English; FCC Class A Notice

Precautions This symbol is intended to alert the user of importantoperating and maintenance (servicing) instructionsin the literature provided with the equipment. This symbol is intended to alert the user of thepresence of uninsulated dangerous voltage withinthe product's enclosure that may present ...

Page 3 - Chapter 1 • Introduction; Table of Contents

P/2 DA2 WM/EC Table of Contents Chapter 1 • Introduction ......................................................... 1-1 About the P/2 DA2 WM/EC andP/2 DA2 WM/EC AAP ............................................................. 1-2 Features ................................................................

Page 4 - Chapter One; Introduction; Features

P/2 DA2 WM/EC Table of Contents P/2 DA2 WM/EC Table of Contents 1 Chapter One Introduction About the P/2 DA2 WM/EC and P/2 DA2 WM/EC AAP Features P/2 DA2 WM/EC

Page 5 - Chapter Two; Controls and Installation; Front and Rear Panels; Stereo audio

P/2 DA2 WM/EC Introduction P/2 DA2 WM/EC Introduction 2 Chapter Two Controls and Installation Front and Rear Panels Installing the P/2 DA2 WM/EC P/2 DA2 WM/EC Introduction About the P/2 DA2 WM/EC and P/2 DA2WM/EC AAP The P/2 DA2 WM/EC and P/2 DA2 WM/EC AAP are a oneinput, two output, high resolution...

Page 6 - Figure 2-2 — P/2 DA2 EC faceplate features; Rear connectors; Front faceplate; Figure 2-1 — P/2 DA2 WM faceplate features

P/2 DA2 WM/EC Controls and Installation P/2 DA2 WM/EC Controls and Installation Unity – output signal level is same as that of input with no added peaking 50% – increases the output signal level and adds 50% of the maximum peaking to the signal If the edges of the image seem to exceed theirboundarie...

Page 7 - “Euro Channel installation” section.; Installing the mounting bracket; Figure 2-4 — Installing the mounting bracket; Easy setup procedure; Controls and Installation, cont’d

P/2 DA2 WM/EC Controls and Installation P/2 DA2 WM/EC Controls and Installation “Euro Channel installation” section. 6 Power up all of the input and output devices. 7 The image should now display on screen. If it doesnot, double check steps 3 through 6 and makeadjustments as needed. Refer to the sec...

Page 8 - Connecting audio output; Unbalanced audio; Cabling

P/2 DA2 WM/EC Controls and Installation P/2 DA2 WM/EC Controls and Installation 2-7 Connecting audio output Before connecting audio output, determine whether youraudio system is unbalanced or balanced. Then, follow theinstructions below to connect unbalanced audio, or theinstructions for “Balanced a...

Page 9 - Installing Architectural Adapter Plates; Figure 2-7 — Installing adapter plates; Figure 2-6 — Fastening captive screws; Balanced audio

P/2 DA2 WM/EC Controls and Installation P/2 DA2 WM/EC Controls and Installation 2-9 3. Slide the audio cable connector into the audio outputconnector on the interface. Installing Architectural Adapter Plates The P/2 DA2 WM AAP may have up to 4 optional adapterplates and the P/2 DA2 EC AAP can have u...

Page 10 - P/2 DA2 EC Euro Channel installation; Figure 2-9 — Euro Channel installation; Setting the DIP switches; ON — Set both pins to On if you are using the; P/2 DA2 WM wallmount installation; Figure 2-8 — Wall mounting the P/2 DA2 WM

P/2 DA2 WM/EC Controls and Installation P/2 DA2 WM/EC Controls and Installation 2-10 2-11 P/2 DA2 EC Euro Channel installation Once the input and output cables have been connected andtested on the P/2 DA2 EC, the distribution amplifier can beeasily installed in the Euro Channel. See figure 2-9. Figu...

Page 11 - Appendix; Specifications; OFF — Set both pins to Off if you are attaching a

P/2 DA2 WM/EC Controls and Installation P/2 DA2 WM/EC Operation A Appendix Specifications Faceplate Dimensions Cables Architectural Adapter Plates Mounting Templates P/2 DA2 WM/EC Controls and Installation, cont’d 2-12 OFF — Set both pins to Off if you are attaching a local monitor to the P/2 DA2 WM...

Page 12 - external; Specifications are subject to change without notice.; peaking

P/2 DA2 WM/EC Appendix P/2 DA2 WM/EC Appendix A-3 Audio input Number/signal type ................... 1 stereo, unbalancedConnectors .................................... 1 3.5 mm female stereo jack, 2 channel; tip (L), ring (R), sleeve (GND) Impedance .................................... 50 ohms, unb...

Page 13 - P/2 DA2 WM Faceplate Dimensions; Figure A-1 — WM model faceplate dimensions; Figure A-2 — WM model AAP faceplate dimensions; All dimensions are given in inches.

P/2 DA2 WM/EC Appendix P/2 DA2 WM/EC Appendix Appendix, cont’d A-4 P/2 DA2 WM Faceplate Dimensions Dimensions of the P/2 DA2 WM and its AAP version areprovided here for those who wish to make their owncustomized faceplate. The following diagrams are not drawn toscale. Figure A-1 — WM model faceplate...

Page 14 - Optional Architectural Adapter Plates; Figure A-3 — Examples of adapter plates; Cables; Part number

P/2 DA2 WM/EC Appendix P/2 DA2 WM/EC Appendix A-7 Optional Architectural Adapter Plates A variety of optional adapter plates for pass-throughconnections may be ordered for the P/2 DA2 WM/EC. See thefigure A-3 below. The WM model can accommodate up to 4adapter plates and the EC model can handle up to...

Page 16 - P/2 DA2 WM Mounting Template; The light gray area represents where; al

P/2 DA2 WM/EC Appendix P/2 DA2 WM/EC Appendix P/2 DA2 WM Mounting Template Use this template as a guide for cutting the hole in theinstallation surface (wall or furniture). This diagram is shownat actual size. The light gray area represents where the P/2 DA2 WM enclosure (2.562” H x 3.437” W) will b...

Page 17 - P/2 DA2 WM AAP Mounting T

A-12 The dashed line indicates the recommended cut-out area (3.875” H x 7.525” W) for the installation surface. The solid, outer line (4.50” H x8.325” W) represents the outside edge of the wall mounting bracket. P/2 DA2 WM AAP Mounting T emplate (shown in actual size)