Extron MTP 15HD - Manuals

Extron MTP 15HD – Manual in PDF format online.

Manuals:

Manual

Manual Extron MTP 15HD

Summary

Page 2 - Korean; Safety Instructions

Safety Instructions • English WARNING : This symbol, , when used on the product, is intended to alert the user of the presence of uninsulated dangerous voltage within the product’s enclosure that may present a risk of electric shock. ATTENTION: This symbol, , when used on the product, is intended to...

FCC Class A Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. The Class A limits provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equ...

Page 4 - Conventions Used in this Guide; Notifications; potential; Specifications Availability

Conventions Used in this Guide Notifications The following notifications are used in this guide: WARNING: A warning indicates a situation that has the potential to result in death or severe injury. ATTENTION: Attention indicates a situation that may damage or destroy the product or associated equipm...

Page 5 - Contents; Installation; MTP 15HD RS Series • Contents

Contents Introduction ............................................ 1 About this Guide .............................................. 1About the MTP Transmitters and Receivers ..... 1 Twisted Pair Cable Advantages .................... 2 Transmission Distance ..................................... 3 In...

Page 7 - Introduction; About this Guide; Extron Enhanced Skew-Free AV UTP cable; About the MTP Transmitters and Receivers; MTP 15HD RS Series • Introduction

Introduction This section gives an overview of the user guide. This section also describes the MTP 15HD RS series of transmitters and receivers. Topics that are covered include: • About this Guide • About the MTP Transmitters and Receivers • Transmission Distance About this Guide This guide contains...

Page 8 - Twisted Pair Cable Advantages

The RS-232 portion of the twisted pair link: • Can be bidirectional in a one-receiver system; that is, the receiver can receive commands from the transmitter and pass RS-232 responses to the transmitter. • Supports software flow control (XON, XOFF). NOTE: Hardware flow control is not supported. • Su...

Page 9 - Transmission Distance; on page

Transmission Distance The maximum distance is determined by the frequency and resolution of the signal that is input to the transmitter. The table on page 4 specifies the recommended maximum transmission distances and transmitter Pre-Peak switch positions (see item e on page 9 ) using Extron Enhance...

Page 11 - Installation and Operation Overview; Potential damage to property.; MTP 15HD RS Series • Installation and Operation

Installation and Operation This section provides information on: • Installation and Operation Overview • Front Panel Features • Transmitter Rear Panel Features • Receiver Rear Panel Features • Power Supply Wiring and Grounding • Twisted Pair Cable Termination • Skew Delay Compensation • EDID Configu...

Page 12 - Front Panel Features; MTP Front Panels; Record LED; The recessed record button initiates recording of the EDID of a; MTP 15HD RS Series • Installation and Operation

Front Panel Features See figure 2 to identify the front panel features on the transmitter and receiver. MTP RL 15HD RS receiver MTP T 15HD RS transmitter MTP RL 15HD RS SEQ receiver RGB PEAKING LEVEL RGB DELAY PEAKING LEVEL MTP SERIES REDGREEN ADJUST BLUE SELECT 50 Hz RECORD 60 Hz SPARE EDID SELECT ...

Page 14 - End Unit switch

j Delay (skew adjustment) control (SEQ model only) — This control delays the selected red, green, or blue video signal by up to 62 nanoseconds. The delay is applied in incremental, 2-nanosecond steps. Rotate the control counterclockwise to reduce the delay or clockwise to increase the delay. NOTES: ...

Page 15 - Transmitter Rear Panel Features; Power Supply Wiring

Transmitter Rear Panel Features Figure 3 shows the rear of an MTP T 15HD RS transmitter. OUTPUT INPUT POWER 12V 0.5A MAX Tx Rx G RS-232 MONITOR PRE-PEAK ON OFF M T P T 1 5 H D R S 1 2 3 6 4 5 Figure 3. Transmitter Rear Panel NOTE: Control signal ground pins may be labeled as or “G”. Audio ground pin...

Page 17 - Receiver Rear Panel Features; Power Supply Wiring and Grounding

Receiver Rear Panel Features Figure 6 shows an MTP RL 15HD RS receiver. INPUT BUFFERED OUTPUT OUTPUT POWER 12V 0.5A MAX M T P R L 1 5 H D R S RS-232 Rx Tx OUTPUTS G 1 2 3 4 3 Figure 6. Receiver Rear Panel NOTE: Control signal ground pins may be labeled as or “G”. Audio ground pins may be labeled as ...

Page 18 - Figure 7 shows how to wire and ground the connector.; SECTION A–A; Power Connector Wiring and Grounding

Power Supply Wiring and Grounding Figure 7 shows how to wire and ground the connector. ATTENTION: Potential damage to property. • Power supply voltage polarity is critical. Incorrect voltage polarity can damage the power supply and the transmitter or receiver. Identify the power cord negative lead b...

Page 20 - Twisted Pair Cable Termination; use the same standard; Connector; When using Enhanced Skew-Free; Twisted Pair Cable Termination Diagram; For proper grounding of; shielded twisted pair cable; , ensure the shield around; should not; be used to

Twisted Pair Cable Termination Figure 8 details the recommended termination of twisted pair cables with RJ-45 connectors in accordance with the TIA/EIA T568A or TIA/EIA T568B wiring standards. You can use either standard with CAT 5, 5e, and 6 cable, but ensure that you use the same standard on both ...

Page 21 - Skew Delay Compensation; SEQ Receiver Skew Compensation; Zero the skew delay; Non-SEQ Receiver Skew Compensation

Skew Delay Compensation CAT 5, 5e, and 6 cable can lead to registration errors between the red, green, and blue video signals. Pair skew can be measured with test equipment or identified by viewing a crosshatch test pattern with a critical eye to determine if either the red, green, or blue video ima...

Page 22 - EDID Configuration; Recording a Display EDID; Switch Position

MTP 15HD RS Series • Installation and Operation 16 EDID Configuration The MTP 15HD RS transmitter can either record EDID from a display device, or a pre-programmed EDID can be selected using the rotary and DIP switches. Recording a Display EDID 1. Turn the rotary switch to position 0. NOTE: The vert...

Page 23 - Mounting; Tabletop Placement; UL Guidelines for Rack Mounting; Elevated operating ambient temperature; MTP 15HD RS Series • Mounting

Mounting This section outlines the various mounting options available for the MTP 15HD RS Series transmitters and receivers: • Tabletop Placement • Under-Desk and Furniture Mounting • Rack Mounting • Projector Mounting Tabletop Placement Attach the four provided rubber feet to the bottom of the unit...

Page 24 - ). The kit allows the product to be vertically mounted to the front or; Projector Mounting

Rack Mounting Procedure These units can be mounted an optional rack systems listed on the website (see www.extron.com ). To mount the unit on a rack shelf, follow the instructions provided with the shelf accessories. Back of the Rack Mounting Procedure The MTP can be mounted to the rear of a rack us...

Page 25 - Contact Information; Extron Warranty; USA; xtron

Extron Headquarters +1.800.633.9876 (Inside USA/Canada Only)Extron USA - West Extron USA - East +1.714.491.1500 +1.919.850.1000 +1.714.491.1517 FAX +1.919.850.1001 FAX Extron Europe +800.3987.6673 (Inside Europe Only)+31.33.453.4040 +31.33.453.4050 FAX Extron Asia +800.7339.8766 (Inside Asia Only)+6...