Extron DVI-RGB 200 - Manuals

Extron DVI-RGB 200 – Manual in PDF format online.

Manuals:

Manual

Manual Extron DVI-RGB 200

Summary

Page 2 - Instrucciones de seguridad • Español; 安全须知; 注意

This symbol is intended to alert the user of important operating and mainte-nance (servicing) instructions in the literature provided with the equipment. This symbol is intended to alert the user of the presence of uninsulated dangerous voltage within the product’s enclosure that may present a risk ...

Page 3 - FCC Class A Notice; This device may not cause harmful interference.; click here; Notational Conventions Used in this Guide; A note draws attention to important information.; Copyright; © 2010 Extron Electronics. All rights reserved.; Trademarks

FCC Class A Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interferen...

Page 4 - Contents; DVI Connector Pin Assignments; DVI-RGB 200 • Contents

Contents Introduction ............................................ 1 Installation and Operation ..................... 2 Installation Overview ........................................ 2Mounting the Interface .................................... 2Rear Panel Connections and Controls ............... 3 D...

Page 6 - Introduction; Typical DVI-RGB 200 Application; transmission across long distances.; DVI-RGB 200 • Introduction

Introduction The Extron DVI-RGB 200 DVI to analog RGB video interface converts DVI digital video to analog RGB video. The interface accepts a single link of digital-only Digital Visual Interface (DVI-D) video from a computer, or other digital video source device, on a standard 29-pin female DVI-I co...

Page 7 - Installation Overview; all turned off and disconnected from the power source.; Mounting the Interface; Detailed mounting instructions can be found in the; DVI-RGB 200 • Installation and Operation

Installation and Operation This sections details the installation and operation of the DVI-RGB 200, including: • Installation Overview • Mounting the Interface • Rear Panel Connections and Control • Front Panel Controls and Indicator • Operation Installation Overview Follow these steps to install an...

Page 8 - Rear Panel Connections and Controls; If desired, connect a direct digital local monitor; Capturing a User-recorded EDID; Set this switch to the Monitor (up) position; User EDID; See page 6

Rear Panel Connections and Controls 100-240V 0.4A 50/60 Hz OUTPUT DVI-DINPUT BUFFERED LOOP-THROUGH R H G V B S SOG ON/OFF REFRESH EDID SOURCE MONITOR HIGH LOW SELECTOR EDID SELECT DVI-RGB 200 2 1 5 7 3 6 4 Figure 2. DVI-RGB 200 Rear Panel a Input connector — Connect a single link of direct digital v...

Page 9 - DIP switches —; Set this switch to the On (up) position to; Refresh switch —; select the refresh rate of the selected output (see; table 1; DVI Connectors; Limit or avoid the use of adapters.

f DIP switches — SOG (Sync on Green) On/Off switch — Set this switch to the On (up) position to enable SOG for RGsB video. Set this switch to the Off (down) position to disable SOG for RGBS or RGBHV video. Refresh switch — If the EDID Source switch ( d ) is in the Selector position and the EDID sele...

Page 10 - Front Panel Controls and Indicator; The two-tone Power LED lights amber or green:

Front Panel Controls and Indicator DVI-RGB 200 DVI TO RGB CONVERTER BOOST LEVEL CONTROL PEAK 8 9 10 Figure 4. DVI-RGB 200 Front Panel h Power LED — The two-tone Power LED lights amber or green: • Amber when the DVI-RGB 200 is receiving power but no DVI input signal is applied. • Green when the DVI-R...

Page 11 - Operation; rate, otherwise images may be distorted or missing.; Connect the; unpowered; in step

Operation After the DVI-RGB 200 and its connected devices are powered up, the system is fully operational. If you encounter any problems, verify that the cables are routed and connected properly. NOTES: • High-bandwidth Digital Content Protection (HDCP) is an encryption method that protects copyrigh...

Page 12 - Specifications; Video; tables; Video input and loop through; single link DVI-D buffered loop-through; Video output; DVI-RGB 200 • Reference Information

Reference Information This section discusses the specifications, part numbers, and accessories for the DVI-RGB 200. Topics that are covered, include: • Specifications • Part Numbers • Mounting the Interface Specifications Video NOTES: • The DVI-RGB 200 converts a single link DVI signal to an analog ...

Page 13 - Specifications are subject to change without notice

Sync Output type ................................... RGBHV, RGBS, RGsBOutput level ................................... TTL (5 Vp-p, unterminated)Output impedance ......................... 75 ohmsPolarity ........................................... Positive or negative (follows input) General Power ....

Page 14 - Part Numbers; Interface Part Numbers; under-desk mount kit; Accessories; These items can be ordered separately:

Part Numbers Interface Part Numbers These items are included in each order for a DVI-RGB 200: Interface and included parts Part number DVI-RGB 200 60-1064-01 IEC power cord Tweeker (small screwdriver) DVI-RGB 200 Setup Guide Mounting Accessories Mounting Kit Part Number RSU 126 6-inch deep 1U univer...

Page 15 - Tabletop Use; figure 5; UL Guidelines for Rack Mounting; Elevated operating ambient —

Mounting the Interface CAUTION: Installation and service must be performed by authorized personnel only. The 1U high, half rack width DVI-RGB 200 can be placed on a tabletop, mounted on a rack shelf, or mounted under a desk or tabletop. Tabletop Use Affix the four included rubber feet to the bottom ...

Page 16 - Rack shelf mounting instructions; The unit can be mounted in the front or the rear of the rack.; Mounting the Unit on a 3-inch Rack Shelf; Attach the rack shelf to the rack using the supplied bolts.; Mounting the Unit on a Universal Rack Shelf

Rack shelf mounting instructions The unit can be mounted in the front or the rear of the rack. 1. Remove the feet from the bottom of the unit if installed. 2. Mount the unit on the rack shelf, using two 4-40 x 3/16-inch screws in opposite (diagonal) corners to secure it to the shelf (figure 5). 6...

Page 17 - Furniture Mounting; Under-Furniture Mounting; Remove feet from the bottom of the unit if installed.

Furniture Mounting Under-Furniture Mounting The unit can be mounted under a horizontal surface using an optional MBU 125 under-desk mounting kit (part #70-077-01). Mount the unit under a desk or table as follows: 1. Remove feet from the bottom of the unit if installed. 2. Secure the under-desk mount...

Page 18 - Through-furniture mounting; Through-desk Mounting; Mark the location of the brackets relative to the screws.

Through-furniture mounting The interface can be mounted through a desk or other furniture using an optional Extron MBD 129 through-desk mounting kit (part #70-077-02). Mount the unit through a desk or table as follows (figure 8): Figure 8. Through-desk Mounting 1. Loosely attach the mounting bracket...

Page 19 - and Central America:; USA; xtron

Extron ® Warranty Extron Electronics warrants this product against defects in materials and workmanship for a period of three years from the date of purchase. In the event of malfunction during the warranty period attributable directly to faulty workmanship and/or materials, Extron Electronics will,...