Page 2 - Precautions; Safety Instructions • English; Instrucciones de seguridad • Español
Precautions This symbol is intended to alert the user of important operating and maintenance (servicing) instructions in the literature provided with the equipment. This symbol is intended to alert the user of the presence of uninsulated dangerous voltage within the product’s enclosure that may pres...
Page 3 - 注意; 声明; FCC Class A Notice
安全须知 • 中文 这个符号提示用户该设备用户手册中有重要的操作和维护说明。 这个符号警告用户该设备机壳内有暴 露的危险电压,有触电危险。 注意 阅读说明书 • 用 户 使 用 该 设 备 前 必 须 阅 读 并 理 解 所 有 安 全 和 使 用 说 明 。 保存说明书 • 用户应保存安全说明书以备将来使 用。 遵守警告 • 用户应遵守产品和用户指南上的所有安 全和操作说明。 避免追加 • 不要使用该产品厂商没有推荐的工具或 追加设备,以避免危险。 警告 电源 • 该 设 备 只 能 使 用 产 品 上 标 明 的 电 源 。 设 备 必 须 使 用 有 地 线 的 供 电 系 统 供 电 ...
Page 5 - DVI DL 201 Tx/Rx • Quick Start Guide; Quick Start Guide — DVI DL 201 Tx/Rx
DVI DL 201 Tx/Rx • Quick Start Guide QS-1 Quick Start Guide — DVI DL 201 Tx/Rx The DVI DL 201 Tx/Rx extends DVI-D signals up to 100' (30 m) at resolutions up to 2560x1600 @ 60 Hz, using twisted pair (TP) cable. Install, connect, and operate the DVI DL 201 Tx/Rx as follows: Step 1 Turn off all equipm...
Page 6 - Quick Start Guide — DVI DL 201 Tx/Rx, cont’d; To use DDC pass-through routed to the remote display:; If there are any problems, consult the troubleshooting section
DVI DL 201 Tx/Rx • Quick Start Guide Quick Start Guide — DVI DL 201 Tx/Rx, cont’d QS-2 To use DDC pass-through routed to the local monitor:a . Configure the DDC switches as shown in the figure at right and described on page 3-4. b . Connect a source device to the transmitter. c . Connect a display d...
Page 7 - DVI DL 201 Tx/Rx • Table of Contents; Chapter One • Introduction; Table of Contents
i DVI DL 201 Tx/Rx • Table of Contents i Chapter One • Introduction .................................................... 1-1 About this Manual .................................................................... 1-2 About the DVI DL 201 Tx/Rx .................................................. 1-2 DV...
Page 8 - Table of Contents, cont’d; Chapter Three • Configuration and Operation; Using the EDID Minder with the default EDID; Appendix A • Reference Information
ii DVI DL 201 Tx/Rx • Table of Contents Table of Contents, cont’d Chapter Three • Configuration and Operation ......... 3-1 Configuration .............................................................................. 3-2 Using the EDID Minder to read and store EDID from a display ......................
Page 9 - Chapter One; Introduction; About this Manual
DVI DL 201 Tx/Rx 1 Chapter One Introduction About this Manual About the DVI DL 201 Tx/Rx DVI DL 201 Tx/Rx Features
Page 10 - DVI DL 201 Tx/Rx • Introduction; The DVI DL 201 Tx/Rx works with unshielded twisted; DVI DL 201 Tx/Rx Features; Long distance transmission —
DVI DL 201 Tx/Rx • Introduction Introduction About this Manual This manual contains information about the DVI DL 201 Tx/Rx signal transmitter and receiver, with information on how to mount, install, and operate these units.In this manual, unless otherwise specified, the terms "DVI DL 201" or...
Page 11 - EDID Minder —; The EDID Minder maintains continuous EDID; Control communications pass-through —; The transmitter is 1U high, a half rack wide; Remote powering of receiver —; A single power supply,; Typical Application for the DVI DL 201 Tx/Rx
DVI DL 201 Tx/Rx • Introduction 1-3 EDID Minder — The EDID Minder maintains continuous EDID (Extended Display Identification Data) communication with the attached source. This ensures that the DVI source powers up correctly and maintains a proper video output, even if the display is off. Control com...
Page 13 - Chapter Two; Installation; Mounting the DVI DL 201 Tx/Rx
DVI DL 201 Tx/Rx 2 Chapter Two Installation Mounting the DVI DL 201 Tx/Rx Panel Features Cable Connections and Switches
Page 14 - DVI DL 201 Tx/Rx • Installation; Tabletop placement; UL guidelines for rack mounting
DVI DL 201 Tx/Rx • Installation Installation Mounting the DVI DL 201 Tx/Rx The transmitter is 1U high, a half rack wide and 3" deep, for easy rack mounting near the source device.The receiver is 1" high, a quarter rack wide and 3" deep, allowing multiple mounting options near the display...
Page 15 - Rack mounting procedures; HalfRackVersaToolsStandardShelf; Installing the DVI DL 201 Tx on a rack shelf
DVI DL 201 Tx/Rx • Installation Rack mounting procedures The unit can be mounted in the front or rear of: RSU 126 (6" deep 1U universal rack shelf kit: PN • 60-190-10 ) RSB 126 (6" deep 1U basic rack shelf: PN • 60-604-10 ) RSU 129 (9.5" deep 1U universal rack shelf kit: PN • 60-190-01 )...
Page 16 - Under-desk mounting the DVI DL 201 Tx
DVI DL 201 Tx/Rx • Installation Installation, cont’d 2-4 Under-desk mounting The figure below shows how to mount the DVI DL 201 Tx under a desk or podium, using the optional Extron MBU 123 under desk mounting kit (PN 70-212-01 ). To mount the DVI DL 201 Rx, the optional Extron MBU 125 under desk mou...
Page 17 - Through-desk mounting; Through-desk mounting the DVI DL 201 Rx
DVI DL 201 Tx/Rx • Installation 2-5 Through-desk mounting The DVI DL 201 Tx should not be mounted through a desk. To mount the DVI DL 201 Rx through a desk or podium, use the optional Extron MBD 129 through-desk mounting kit (PN 70-077-02 ), and follow these instructions: 1 . Remove rubber feet if t...
Page 18 - Pole mounting; Rubber Pad; Projector mounting the DVI DL 201 Rx
DVI DL 201 Tx/Rx • Installation Installation, cont’d 2-6 Pole mounting The instructions for mounting the receiver on the projector pole, using the PMK 300 pole mounting kit (PN 70-374-01 ), are shown below. For instructions on using any other Extron projector mounting kit, consult the appropriate us...
Page 20 - Panel Features; The illustration below shows the front panel features of the; DVI DL 201 Tx front panel features; LED —; An amber light indicates that the DVI DL 201 Tx is
DVI DL 201 Tx/Rx • Installation Installation, cont’d 2-8 Panel Features DVI DL 201 Tx front panel features The illustration below shows the front panel features of the DVI DL 201 Tx. DVI DL 201 Tx DVI DUAL LINK TRANSMITTER 1 DVI DL 201 Tx front panel features a LED — An amber light indicates that th...
Page 21 - DVI DL 201 Tx rear panel features
DVI DL 201 Tx/Rx • Installation 2-9 DVI DL 201 Tx rear panel features The illustration below shows the rear panel features of the DVI DL 201 Tx. 12V 0.4A MAX POWER DVI-D INPUT LOCAL OUTPUT OUTPUTS DO NOT CONNECT OUTPUTS TO LAN 1 2 3 SN XXXXXXXX E XXXXX 00/00 DVI DL TX STORE EDID Tx Rx CONTROL PASS T...
Page 22 - DVI DL 201 Rx front panel features; Power LED —
DVI DL 201 Tx/Rx • Installation Installation, cont’d 2-10 DVI DL 201 Rx front panel features The illustration below shows the front panel features of the DVI DL 201 Rx. DVI 201 Rx SERIES Tx Rx CONTROL PASS THRU 9 11 DVI-D OUTPUT 10 DVI DL 201 Rx front panel features i Power LED — An amber light indi...
Page 23 - The illustration below shows the rear panel features of the; DVI DL 201 Rx rear panel features; Power input —; An optional 12 VDC power supply (not; Twisted pair inputs —; Three RJ-45 jacks receive video, remote
DVI DL 201 Tx/Rx • Installation 2-11 DVI DL 201 Rx rear panel features The illustration below shows the rear panel features of the DVI DL 201 Rx. POWER 12V 0.4A MAX 12 INPUTS 1 2 3 13 DO NOT CONNECT INPUTS TO LAN D VI DL 201 Rx DVI DL 201 Rx rear panel features l Power input — An optional 12 VDC pow...
Page 24 - Cable Connections and Switches; Although DVI-I connectors are used, the DVI DL 201 is
DVI DL 201 Tx/Rx • Installation Installation, cont’d 2-12 Cable Connections and Switches DVI-D input Connect the DVI-D source device to the female DVI-I input connector.The dual link DVI-D input carries a signal with a resolution up to 2560x1600 @ 60 Hz.For sources providing HDMI signals, use an HDM...
Page 26 - Twisted pair output/input; Terminating shielded cable; The transmitter and receiver pair works with unshielded
DVI DL 201 Tx/Rx • Installation Installation, cont’d 2-14 Twisted pair output/input Terminating shielded cable CAT 5/5e/6/7 twisted pair cable is not provided with the transmitter/receiver pair. You may purchase cables that have been precut to the required length and terminated to the T586A or T586B...
Page 27 - Wire color; Connections; Connector
DVI DL 201 Tx/Rx • Installation 2-15 Pin # TIA/EIA T 586 A Wire color TIA/EIA T 586 B Wire color Cable 1 Cable 2 Cable 3 1 White-green White-orange Data 0+ CEC Data 3+ 2 Green Orange Data 0+ HPD Data 3+ 3 White-orange White-green IDCK+ RS-232 Tx/IR+ N/C 4 Blue Blue Data 1+ DDC Clock Data 4+ 5 White-...
Page 28 - Single Link/Dual Link DVI; Dual Link DVI carries signals at resolutions up to; Video Resolution; Single Link Mode; UTP; The transmission distance varies greatly depending on
DVI DL 201 Tx/Rx • Installation Installation, cont’d 2-16 Single Link/Dual Link DVI Dual Link DVI carries signals at resolutions up to 2560x1600 @ 60 Hz. Single Link DVI carries signals at resolutions up to 1920x1200 @ 60 Hz. Video Resolution (60 Hz) Single Link Mode Dual Link Mode UTP STP UTP STP 1...
Page 29 - DDC switches
DVI DL 201 Tx/Rx • Installation 2-17 DDC switches When the DVI-D source device boots up, it uses the Display Data Channel (DDC), a two-way communication protocol, to obtain Extended Display Identification Data (EDID) from the display device. This allows the source to output a resolution that matches...
Page 31 - For information about controlling display devices with; IR signals
DVI DL 201 Tx/Rx • Installation 2-19 RS-232 signals RS-232 signals are bidirectional — signals pass from the control device and replies return from the remote device. To connect the control device to the transmitter, or the receiver to the remote device, make the following connections, as shown at r...
Page 32 - Power input; Power supply voltage polarity is critical. Incorrect; Connecting power to DVI DL 201 Tx/Rx
DVI DL 201 Tx/Rx • Installation Installation, cont’d 2-20 Power input 1 . Connect the captive screw connector from the supplied 12 VDC power supply into the power receptacle. Twisted pair cable 2, pin 5 carries a 12 VDC power signal. This remote powering feature allows a single power supply, connect...
Page 33 - Chapter Three; Configuration and Operation; Configuration
DVI DL 201 Tx/Rx 3 Chapter Three Configuration and Operation Configuration Setup and Operation Troubleshooting
Page 34 - DVI DL 201 Tx/Rx • Configuration and Operation; Using the EDID Minder to read and store EDID; The EDID Minder extracts information only from the
DVI DL 201 Tx/Rx • Configuration and Operation Configuration and Operation Configuration Using the EDID Minder to read and store EDID from a display During boot up, the DVI-D source device uses Display Data Channel (DDC) to obtain Extended Display Identification Data (EDID) from the display device. ...
Page 35 - All display devices must be capable of handling
DVI DL 201 Tx/Rx • Configuration and Operation 10 . Power up the transmitter and the receiver. A single power supply can provide power to both units through the remote power connection. 11 . Connect the remote display to the receiver output. A local monitor display can also be connected to the trans...
Page 36 - Configuration and Operation, cont’d; Using pass-through mode with DDC routed to a; Because the local monitor is the source of EDID, it must
DVI DL 201 Tx/Rx • Configuration and Operation Configuration and Operation, cont’d 3-4 Using pass-through mode with DDC routed to a local monitor 1 . Set the EDID Minder switch to the off (down) position and the Default EDID switch to the off (down) position (see the figure at right). The position o...
Page 37 - Using pass-through mode with DDC routed to the
DVI DL 201 Tx/Rx • Configuration and Operation 3-5 Using pass-through mode with DDC routed to the remote display N This is the factory default setting. N Although DDC can be routed to the remote display, there may be instances when the signals become corrupted or weak. In those cases, the source dev...
Page 38 - No output signal —; Do not try to power both units with a single power
DVI DL 201 Tx/Rx • Configuration and Operation Configuration and Operation, cont’d 3-6 Setup 1 . Determine which source will be used for the EDID information and configure the DDC switches appropriately (see pages 3-2 to 3-5). If necessary, use the EDID Minder to read and store information from a di...
Page 39 - No output signal or poor quality signal —; Image loss or jitter —
DVI DL 201 Tx/Rx • Configuration and Operation 3-7 Insure all three twisted pair cables are firmly seated in the correct receptacles. No output signal or poor quality signal — Check the integrity of the UTP or STP cables between the transmitter and the receiver. N The transmitter and receiver pair w...
Page 40 - Signal on local monitor but not on remote display —
DVI DL 201 Tx/Rx • Configuration and Operation Configuration and Operation, cont’d 3-8 Display device displays a flashing black or blue screen, snow, or other distortion — A device that is not High-Bandwidth Digital Content Protection (HDCP) compliant may be receiving HDCP-encrypted signals.The DVI ...
Page 41 - Appendix A; Reference Information; Specifications
DVI DL 201 Tx/Rx A Appendix A Reference Information Specifications Included Parts Optional Accessories
Page 42 - DVI DL 201 Tx/Rx • Reference Information; Video; Signal transmission distance
DVI DL 201 Tx/Rx • Reference Information Reference Information A-2 Specifications Video Maximum data rate....................... 10 Gbps (3.3 Gbps per color)Maximum pixel clock ................... 330 MHz (165 MHz per link)Resolution range ........................... Up to 2560x1600 @ 60 HzFormats ....
Page 43 - Video output — receiver; Serial control port input; Protocol is mirrored between the transmitter and the receiver.; General; receiver
DVI DL 201 Tx/Rx • Reference Information A-3 Video output — receiver Number/signal type ..................... 1 dual link DVI-D N Dual link DVI is backwards compatible with all single link DVI/HDMI signals. Connectors ..................................... 1 DVI-I female Control/remote — external dev...
Page 44 - Regulatory compliance; Specifications are subject to change without notice.
DVI DL 201 Tx/Rx • Reference Information Reference Information A-4 Cooling ........................................... Convection, no ventsMounting Rack mount ........................ Yes, with optional 1U, 9.5" deep rack shelf (RSU 129, #60-190-01 or RSB 129, 60-604-01); 1U, 6" deep rack sh...
Page 45 - Included Parts; Included parts; Optional Accessories; Accessory; PMK 300 Projector mounting kit
DVI DL 201 Tx/Rx • Reference Information Included Parts Included parts Replacement part number (1 pair) DVI DL 201 Tx/Rx 60-957-01 or (1) DVI DL 201 Tx 60-957-12 or (1) DVI DL 201 Rx 60-957-13 (1) 12 VDC, 2A power supply DVI DL 201 Tx/Rx User's Manual Optional Accessories Accessory Part number RSF 1...
Page 47 - Extron’s Warranty; will begin the repair process as quickly as possible.
Extron’s Warranty Extron Electronics warrants this product against defects in materials and workmanship for a period of three years from the date of purchase. In the event of malfunction during the warranty period attributable directly to faulty workmanship and/or materials, Extron Electronics will,...