Extron AVT 200HD - Manuals
Extron AVT 200HD – Manual in PDF format online.
Manuals:
Manual Extron AVT 200HD
Summary
ii This symbol is intended to alert the user of important operating and mainte-nance (servicing) instructions in the literature provided with the equipment. This symbol is intended to alert the user of the presence of uninsulated dangerous voltage within the product enclosure that may present a risk...
iii FCC Class A Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interf...
iv Conventions Used in this Guide In this user guide, the following are used: NOTE: A note draws attention to important information. TIP: A tip provides a suggestion to make working with the application easier. CAUTION: A caution indicates a potential hazard to equipment or data. WARNING: A warning ...
Contents Introduction ............................................................ 1 About this Guide ................................................ 1About the AVT 200HD Tuner .............................. 1Features .............................................................. 1Application Diagr...
HTML Configuration and Control ........................................................... 74 Accessing the Web Pages .................................. 74Special Characters............................................. 75System Status Page ........................................... 76Configuration ...
AVT 200HD Tuner • Introduction 1 Introduction This section gives an overview of the Extron AVT 200HD ATSC and Cable TV HD Tuner and describes its significant features. Topics include: • About this Guide • About the AVT 200HD Tuner • Features • Application Diagram About this Guide This guide contains...
AVT 200HD Tuner • Introduction 3 Application Diagram VID R H V B-Y Y G B R-Y COAX HDMI OPTICAL AIR/CABL E 50/6 0 H z LA N RESE T YC 100-240V 0.8A OUTPUT A U D I O O U T DIGI TAL AUDIO RF IN L L R R Tx IR +12 V RS-232/IR Rx 100 -24 0V 0 .5A 50- 60H z INPUTS DIGI TA L OUTPU TS SSP 7.1 1 2 3 5 ANAL OG ...
AVT 200HD Tuner • Installation 4 Installation This section describes the rear panel of the AVT 200HD and provides instructions for cabling. It covers the following topics: • Installation Overview • Rear Panel Features • Control Connections Installation Overview Follow these steps to install and set ...
AVT 200HD Tuner • Installation 5 Rear Panel Features All of the AVT 200HD connectors are on the rear panel. The following figure shows the AVT rear panel features. VID R H V B-Y Y G B R-Y COAX HDMI OPTICAL AIR/CABLE 50/60 Hz LAN RESET YC 100-240V 0.8A OU TP U T A U D I O O U T DIGITAL AUDIO RF IN L ...
AVT 200HD Tuner • Installation 6 e HDMI video output connector — Connect an HDMI output device to this female HDMI connector for digital video output. This output supports 480p, 720p, and 1080i resolutions. The table below shows the pin assignments for this connector. Pin Signal Pin Signal Pin Signa...
AVT 200HD Tuner • Installation 7 Balanced Audio Output Unbalanced Audio Output Tip Ring Tip Ring LR Sleeve(s) Do not tin the wires! Tip NO Ground Here Sleeve(s) NO Ground Here Tip LR CAUTION: For unbalanced audio, connect the sleeves to the ground contact. DO NOT connect the sleeves to negative (–) ...
AVT 200HD Tuner • Installation 8 Control Connections Ethernet Connection When you connect a computer to the AVT 200HD LAN port, it is vital that you use the correct Ethernet cables, and that they are properly terminated with the correct pinout. Ethernet links use Category (CAT) 5 or 5e unshielded tw...
AVT 200HD Tuner • Installation 9 2. Plug the wired 5-pole connector into the RS-232/IR receptacle on the AVT 200HD rear panel. RS-232/IR Computer orControl SystemRS-232 Port AVT 200HD TunerRear PanelRS-232/IR Port NOTE: If you use cable that has a drain wire, tie the drain wire to ground at both end...
AVT 200HD Tuner • Installation 10 The following diagram shows how to wire the AVT 200HD to use the infrared remote control with the optional IR Link. Modulated IR +12 VDC Ground ( ) D B A IR 12 LAN RESET Tx IR +12V RS-232/IR Rx AVT 200HD Rear Panel RS-232/IR Port IR Link Rear Panel AVT 200HD Remote ...
AVT 200HD Tuner • Installation 11 2. If this is the first time you have connected an AVT 200HD to this USB port on your computer, the Found New Hardware Wizard opens. On the first screen, specify whether you want the computer to connect to Windows Update in order to search the web for the driver tha...
AVT 200HD Tuner • Installation 12 3. Click Next . On the next screen, make sure that the Install the software automatically (Recommended) radio button is selected, then click Next . (You do not need to insert a disc.) Figure 11. Selecting the Radio Button to Install the USB Driver Automatically Your...
AVT 200HD Tuner • Operation 13 Operation This section describes the AVT 200HD front panel controls and the procedures for using them to configure and operate the AVT tuner. Topics include: • Front Panel Features • Powering On • Menus on the LCD Screen • Resetting from the Rear Panel • Locking and Un...
AVT 200HD Tuner • Operation 14 e Up ( > ) and Down ( < ) buttons — These buttons change the channel or preset, depending on the selected operating mode. Each press increments or decrements the number in the LED display ( c ). • In Tune mode (default): The buttons select channel numbers to swit...
AVT 200HD Tuner • Operation 15 Powering On Apply power by connecting the provided IEC power cord to the rear panel IEC connector and to an AC source. The tuner performs a self-test that flashes the three TV format indicators in order from top to bottom and then turns them off while the initial two p...
AVT 200HD Tuner • Operation 16 Menus on the LCD Screen The AVT 200HD menus that are displayed on the LCD screen enable you to configure and operate the tuner from the front panel. The menu navigation buttons (Menu and Next) are located to the right of the LCD window. Press these buttons to cycle thr...
AVT 200HD Tuner • Operation 17 Menu flow diagram The following diagram shows the menus that are displayed in the front panel LCD window and the order in which they appear when you repeatedly press the Menu button. Power On AVT 200HD VERSION X.XX OUTPUT CONFIGURATION 2 sec. Menu Menu AUDIO CONFIGURAT...
AVT 200HD Tuner • Operation 18 Channel Setup Menu The Channel Setup menu lets you select the radio frequency source (over-the-air or cable) and to scan for available channels. CHANNEL SETUP Next RF SOURCE AIR PRESS UP BUTTON TO START SCAN Next > (Up) Menu Default Cycle • AIR (Default) • CABLE STA...
AVT 200HD Tuner • Operation 19 Follow these steps to scan for channels from the front panel. The AVT must be in tune mode. If the desired signal source has already been selected, or if the channel scan is being performed for the first time on this system, skip steps 1 through 3 . 1. Place the AVT in...
AVT 200HD Tuner • Operation 20 • If no channels are found, the LCD screen displays [ RF source ] CHANNEL LIST Empty , alternating with PRESS UP BUTTON to START SCAN . [ SOURCE ] CHANNEL LIST EMPTY If you want to repeat the scan, press the > button. To return to the Channel Setup menu, press the M...
AVT 200HD Tuner • Operation 21 Output Configuration Menu From this menu, you can set output parameters, including resolution and refresh rate, display aspect ratio, and closed captioning. This menu also enable you to select the operating mode (tune or preset). Next OUTPUT CONFIGURATION TUNER MODE TU...
AVT 200HD Tuner • Operation 22 • Preset mode: In preset mode, the Up and Down buttons step up or down through presets that have been saved. NOTE: Using the front panel, SIS commands, the Windows-based control software, the HTML pages, or the IR Remote Control, you can recall presets in tune mode and...
AVT 200HD Tuner • Operation 23 Recalling presets When a channel is saved as a preset, you can tune to that channel by selecting its preset. Using the front panel menus, you can recall a preset that has been saved. When you select a preset, it recalls the cable or over-the-air TV channel that was pro...
AVT 200HD Tuner • Operation 24 Resolution Simultaneous Video Output Composite S-video Component RGBHV HDMI (with embedded audio) 480i @ 59.94 Hz X X X X 480p @ 59.94 Hz X X X* 720p @ 60 Hz X X X 1080i @ 60 Hz (default) X X X *480p HDMI output has a 54 MHz pixel clock. Check with the manufacturer of ...
AVT 200HD Tuner • Operation 25 Figure 21. Display Modes for 4x3 and 16x9 Monitors Selecting the closed caption service The Caption submenu lets you enable closed captioning and select a service. The options are Off (the default) or Service 1 through Service 6 . Primary captioning service is provided...
AVT 200HD Tuner • Operation 26 The following functions are available via the Audio Configuration submenus: • Selecting the digital audio type (Digital Out submenu) — Select the type of digital audio output. The options are AC-3 (Dolby digital surround, the default) or PCM (standard digital audio). •...
AVT 200HD Tuner • Operation 27 Viewing serial port and IP settings The View Comm Setting menu appears after the Audio Configuration menu as you press the Menu button to cycle through the menus. All the View Comm Setting screens that you cycle through by pressing Next show the current settings. You c...
AVT 200HD Tuner • Operation 28 Unit Reset Menu (Resetting from the Front Panel) Three modes of reset can be initiated from the AVT 200HD front panel. Next UNIT RESET FACTORY RESET PRESS NEXT TO RESET Next Menu • FACTORY RESET • RESET USER SETTINGS • CLEAR CH & PRESET LIST VIEW COMM SETTING Next ...
AVT 200HD Tuner • Operation 29 Exiting the Menu System To exit the menu system and return to the default cycle, do either of the following: • Press the Menu button repeatedly until Press Next to Exit is displayed on the LCD screen, then press Next. • Do not press any button. After approximately 30 s...
AVT 200HD Tuner • Operation 30 Reset Modes Summary Mode Activation Result Purpose/Notes 1 Hold in the Reset button while applying power to the tuner. Restores the factory-installed firmware. All user settings and files, such as audio adjustments and IP settings, are retained. Event scripts do not ru...
AVT 200HD Tuner • Operation 31 Locking and Unlocking the Front Panel (Executive Modes) To prevent access by unauthorized users or accidental changes to the AVT 200HD settings, you can lock most of the front panel controls by using executive modes. (The rear panel RS-232 and LAN ports and the front p...
AVT 200HD Tuner • Operation 32 You can access the Exec Mode Select menu when any other menu or submenu is displayed. To select an executive mode: 1. Press the Menu and Next buttons simultaneously and hold them until the LCD window displays the Exec Mode Select menu with the name of the current execu...
AVT 200HD Tuner • Operation 33 IR SDTVEDTVHDTV CONFIG CHANNEL AVT 200HD 40 40 30 ’ (9.1 m) maximum AVT 200HD Remote Control AVT 200HD Remote CHANNEL SELECTION VIDEO TUNE PRESET INFO SAVE ENTER LAST CC GUIDE SHIFT FREEZE VOLUME CHANNEL AUDIO 4 3 2 1 5 6 7 8 0 9 MUTE Figure 27. Area for Remote Signal ...
AVT 200HD Tuner • Operation 34 Buttons on the AVT 200HD Remote Control The following functions are available through the buttons on the AVT 200HD IR Remote Control: AVT 200HD Remote VIDEO TUNE PRESET INFO SAVE ENTER LAST CC GUIDE SHIFT FREEZE VOLUME CHANNEL AUDIO 4 3 2 1 5 6 7 8 0 9 MUTE 14 1 9 4 2 ...
AVT 200HD Tuner • Operation 35 i Guide — Toggles the on-screen Program Guide (list of programs currently available on the selected channel) on and off. j Info — Turns on the on-screen display with information on the current channel. (This button does not turn the display off; after approximately 3 s...
AVT 200HD Tuner • Operation 36 2. Press the Enter button to implement the channel or preset selection. • If the number you entered is a valid channel or an existing preset number, the AVT switches to it, and the number is displayed on the LED panel, aligned with the right position in the field (show...
AVT 200HD Tuner • Operation 37 In the example on below, the current channel is 4.1 (on the OSD, the decimal point is shown as a hyphen); the channel name is NBC–4LA ; the title of the program currently running is “ Today ”; the time is 1:37 pm ; and the signal strength (shown by a vertical bar graph...
AVT 200HD Tuner • Operation 38 Program Guide The translucent program guide display provides a list of the programs available on the current channel for the day. Figure 34. Program Guide Example • To display the program guide , do any of the following: • Press the Guide button on the IR remote contro...
AVT 200HD Tuner • Remote Configuration and Control 39 Remote Configuration and Control This section describes the serial, Ethernet, and USB connections through which the Extron Simple Instruction Set (SIS) commands can be issued, and lists the commands that are available for configuring and controll...
AVT 200HD Tuner • Remote Configuration and Control 40 IP Address To access the AVT 200HD via the Ethernet port, obtain the IP address of the tuner from your network administrator. If the IP address has been changed to an address comprised of words and characters, you can determine the actual numeric...
AVT 200HD Tuner • Remote Configuration and Control 41 Using SIS Commands SIS commands consist of one or more characters per command field. They do not require any special characters to begin or end the command character sequence. Each tuner response to an SIS command ends with a carriage return and ...
AVT 200HD Tuner • Remote Configuration and Control 42 Tuner Error Responses If the AVT is unable to perform an SIS command that it receives because the command is invalid or contains invalid parameters, the tuner returns an error response to the host. Response include: E01 — Invalid input number (to...
AVT 200HD Tuner • Remote Configuration and Control 43 Special Characters The following characters are invalid preset names, the tuner name, passwords, or locally created file names: ~ @ = ` [ ] { } < > ’ ‘ “ ” ; (semicolon) : (colon) | / \ ? and space . Symbol Definitions for AVT 200HD Specifi...
AVT 200HD Tuner • Remote Configuration and Control 45 Command/Response Table for AVT 200HD SIS Commands Command ASCII Command (Host to Tuner) Response (Tuner to Host) Additional Description NOTE: Commands can be entered back-to-back in a string, with no spaces. Example: TvprS25*11 • 3 RF Input and C...
AVT 200HD Tuner • Remote Configuration and Control 46 Command ASCII Command (Host to Tuner) Response (Tuner to Host) Additional Description RF Input and Channel Selection (continued) Tune mode (edited channel list) (continued) View a specific channel on the edited list EX! * X@ TVCH } X1)] In verbos...
AVT 200HD Tuner • Remote Configuration and Control 47 Command ASCII Command (Host to Tuner) Response (Tuner to Host) Additional Description RF Input and Channel Selection (continued) Presets (continued) Name preset EX2% , X2# NG } Nmg X2% , X2#] Assign name X2# to preset X2% . Command character is a...
AVT 200HD Tuner • Remote Configuration and Control 51 Command ASCII Command (Host to Tuner) Response (Tuner to Host) Additional Description Audio Output (continued) Select output language EX* LANG } Lang X*] Set the language of the output to X* . For X* : 0 = English 1 = Spanish 2 = French View lang...
AVT 200HD Tuner • Remote Configuration and Control 55 Command ASCII Command (Host to Tuner) Response (Tuner to Host) Additional Description Resets Clear channel list E 0*TVSL } Tvsl ] Clear all channels. Reset user settings E ZI } Zpi ] Reset all settings to the factory defaults except the channel a...
AVT 200HD Tuner • Remote Configuration and Control 56 Symbol Definitions for IP-specific Commands X4! = Port number 01 – 99 (represented as two ASCII characters with leading zero if required X4@ = Command data section Factory default name (model name + last 3 pairs of MAC address) X4# = GMT offset –...
AVT 200HD Tuner • Remote Configuration and Control 57 X6) = Subnet mask nnn.nnn.nnn.nnn (Leading zeros in each of the four fields are optional for setting values and are suppressed in returned values. Default = 255.255.0.0 X6! = Message length, delimiter value, nL = L ength of message to be received...
AVT 200HD Tuner • Remote Configuration and Control 58 X7& = Event data size b = bit B = byte (8 bits) S = short (16 bits) L = long (32 bits) NOTE: In a write operation, this parameter can optionally be preceded by A (for and ) or O (for or ) to logically combine with content instead of replacing...
AVT 200HD Tuner • Remote Configuration and Control 59 Command/Response Table for IP-Specific SIS Commands Command ASCII Command (Host to Tuner) Response (Tuner to Host) Additional Description Bidirectional Serial Port Send data string EX4! * X5& * X5* * X6! RS } X4@ response from command ] Confi...
AVT 200HD Tuner • Remote Configuration and Control 63 Command ASCII Command (Host to Tuner) Response (Tuner to Host) Additional Description Remap Port Destinations (continued) Set web port map 24 EX4@ MH } Pmh X4@] Reset web port map 24 E 80MH } Pmh00080 ] Disable web port 24 E 0MH } Pmh00000 ] View...
AVT 200HD Tuner • Remote Configuration and Control 66 Accessing the AVT 200HD Configuration & Control Software The Windows-based AVT 200HD Configuration & Control Program provides a convenient way to configure and control the tuner from your computer. All functions that are available from th...
AVT 200HD Tuner • Remote Configuration and Control 67 3. On the Control Software screen, click A on one of the linked alphabets at the top and bottom of the screen if necessary to display the “A” page. 4. Locate the AVT 200HD and click the Download link at the far right. 5. On the next screen, fill ...
AVT 200HD Tuner • Remote Configuration and Control 68 Starting the Software To run the AVT 200HD Configuration & Control Program: 1. Click on the AVT200HD.exe icon (shown at right) in the Extron Electronics group or folder in the Start menu. You can access this icon by selecting Start > All P...
AVT 200HD Tuner • Remote Configuration and Control 69 • RS232 (shown below): From the drop-down menus, select the port, baud rate (the default is 9600 ), parity, data bits, and stop bits. Figure 39. RS232 Connection Tab 3. Click Connect . A Getting Device Settings screen displays status messages whi...
AVT 200HD Tuner • Remote Configuration and Control 70 Figure 41. AVT 200HD Configuration & Control Program Main Window with the Control Tab Displayed 4. To begin configuring the AVT, click the Setup tab. This tab contains several sub-tabs on which you can set up all available AVT parameters. Fig...
AVT 200HD Tuner • Remote Configuration and Control 71 Using the Configuration & Control Program Help File For instructions on using the AVT 200HD Configuration & Control Program to set up and control the AVT, use the program help file. To access it, select Help from the Help menu. Updating t...
AVT 200HD Tuner • Remote Configuration and Control 72 5. Double-click on <double click to set> in the New Firmware File column, or select New Firmware for Selected Devices from the File menu. Figure 43. Extron Firmware Loader Window for AVT 200HD Figure 44. Choose Firmware File Window 6. In th...
AVT 200HD Tuner • Remote Configuration and Control 73 7. In the Firmware Loader window, click Begin . The following indicators on the Firmware Loader window show the progress of the update: • The Transfer Time field shows the amounts of remaining and elapsed time for the update. • The Total Progress...
AVT 200HD Tuner • HTML Configuration and Control 74 HTML Configuration and Control This section provides procedures for accessing and using the AVT embedded web pages. The following topics are included: • Accessing the Web Pages • Special Characters • System Status Page • Configuration Pages • File ...
AVT 200HD Tuner • HTML Configuration and Control 75 4. Press the <Enter> key. The tuner checks to see if it is password protected. • If the tuner is not password protected, the System Status web page opens. • If the AVT is password protected, the network password dialog box is displayed. Figur...
AVT 200HD Tuner • HTML Configuration and Control 76 System Status Page The System Status page provides an overall view of the status of the tuner, including firmware version and serial port settings. The System Status page is the default page that the tuner downloads when you connect to it. You can ...
AVT 200HD Tuner • HTML Configuration and Control 77 Configuration Pages The Configuration tab contains enables you to four pages that only an administrator can access. These pages are listed in the left sidebar menu on the Configuration tab. The following sections describe the changes you can make f...
AVT 200HD Tuner • HTML Configuration and Control 78 IP Settings Fields The IP Settings fields provide a location for viewing and editing settings unique to the Ethernet interface. After editing any of the settings on this page, click the Submit button at the bottom of the IP Settings section. Unit N...
AVT 200HD Tuner • HTML Configuration and Control 79 Date/Time Settings Fields The fields in the Date/Time Settings section let you view and set date and time parameters. Figure 49. Date/Time Settings Fields Change the date and time settings as follows: 1. In each Date or Time field that you want to ...
AVT 200HD Tuner • HTML Configuration and Control 80 Tuner Settings Page On the Tuner Settings page, you can show or hide scanned channels, select the signal source (over-the-air or cable), scan and hide channels, save and recall presets, select the output resolution, and enable or disable front pane...
AVT 200HD Tuner • HTML Configuration and Control 81 Channel Scan section In this section you can select the signal source (ATSC or cable) and initiate scanning for all channels in your area with active signals. To scan for channels using this screen: 1. From the TV Standard drop-down menu, select th...
AVT 200HD Tuner • HTML Configuration and Control 82 Editing or deleting a preset To edit a preset: 1. In the Presets section, select a preset to edit. 2. Click the Edit button. The preset number, channel number, and name of the selected preset are displayed in the Save Preset section. 3. In the Save...
AVT 200HD Tuner • HTML Configuration and Control 83 Passwords Page Access the Passwords page by clicking the Passwords link on the sidebar menu on the System Settings page. Figure 52. Passwords Page Setting a password The fields on the Passwords page are used to enter and verify administrator and us...
AVT 200HD Tuner • HTML Configuration and Control 84 Firmware Upgrade Page The Firmware Upgrade page lets you replace the firmware that is coded on the AVT control board without needing to take the tuner out of service. Access the Firmware Upgrade page by clicking the Firmware Upgrade link on the Sys...
AVT 200HD Tuner • HTML Configuration and Control 85 5. Click the Browse button. A Choose File to Upload window opens. Figure 54. Choose File Window with a Firmware File Selected 6. Navigate to the folder where you saved the firmware upgrade file and double-click on the file name. The Choose Firmware...
AVT 200HD Tuner • HTML Configuration and Control 86 File Management Page The File Management page is a useful tool that allows you to use and upload existing and custom web pages. Custom pages can be developed using a third-party web page development program such as Microsoft Office FrontPage or Ado...
AVT 200HD Tuner • HTML Configuration and Control 87 Adding a Directory To add a directory or folder to the AVT file system: 1. Enter the directory name in the Dir: field, following the slash (/). 2. Click the Add Dir button. 3. With the directory name displayed, perform the uploading files procedure...
AVT 200HD Tuner • HTML Configuration and Control 88 Control Pages From the Control tab, you can access the pages that allow you to set some special features of the AVT 200HD. User Control On the User Control page, you can select channels or presets, mute and unmute audio and video outputs, turn clos...
AVT 200HD Tuner • HTML Configuration and Control 89 Selecting a channel To tune to a channel using the User Control page: 1. Make sure that the AVT is in tune mode (see “ Selecting tune or preset mode ”, on the previous page). 2. Specify the channel number by any of the following methods: • Keypad —...
AVT 200HD Tuner • HTML Configuration and Control 90 Enabling or disabling audio or video muting, image freeze, closed captioning, and the Program Guide To enable or disable muting, image freezing, closed captioning, or the Program Guide, click the Off or On button under the name of the function that...
AVT 200HD Tuner • HTML Configuration and Control 91 • Format the Appearance — To specify the text and background parameters for the closed caption, make your selections from the following menus: Text Size SmallMediumLarge Text Style UndefinedMono Serif Prop. Serif Mono Sans Serif Prop. Sans Serif Ca...
AVT 200HD Tuner • HTML Configuration and Control 92 Figure 59. V-chip Screen 4. On the V-Chip screen, make adjustments as desired in the sections described below. Movie Rating Parental Control section From the Maximum Allowed Moving Rating menu, select the level of movie ratings at which to begin bl...
AVT 200HD Tuner • HTML Configuration and Control 93 TV Rating Parental Control section In this section, you can specify the highest rating level of television programs that will be shown. Programs with higher ratings than your selections are blocked. You can also select the sub-rating (category) of ...
AVT 200HD Tuner • HTML Configuration and Control 94 The Maximum Allowed TV Rating for Ages section contains four submenus from which you can select blocking levels for shows containing the following: D: Suggestive dialog B: Coarse language S: Sexual content V: Violence NOTE: Selections made from the...
AVT 200HD Tuner • HTML Operation 95 AVT 200HD Tuner • Reference Information 95 Reference Information This section provides reference information on the AVT 200HD. The following topics are covered: • Specifications • Part Numbers and Accessories • Mounting the Tuner • IP Addressing • Frequency Tables...
AVT 200HD Tuner • Reference Information 96 96 Scaled resolution ............................ 480i 1 , 480p 1 , 720p 2 , 1080i 2 1 = at 59.94 Hz, 2 = at 60 Hz DC offset ....................................... ±50 mV with input at 0 offset Video output — digital Number/signal type .......................
AVT 200HD Tuner • Reference Information 97 97 IR remote control ........................... AVT 200HD remote (optional) Front panel: 30' maximum, 40 degrees off axis Rear panel captive screw connector (shared with RS-232): 38 kHz, hardwired, modulated Program control ............................. Ex...
AVT 200HD Tuner • Reference Information 98 98 Part Numbers and Accessories Included Parts The following parts are provided with your AVT 200HD. Included Part Replacement Part Number AVT 200HD Tuner 60-770-01 Rubber feet (4) (not attached)US style IEC power cordAVT 200HD Control Software on DVD AVT 2...
AVT 200HD Tuner • Reference Information 99 99 Mounting the Tuner UL Guidelines for Rack Mounting The following Underwriters Laboratories (UL) guidelines pertain to the installation of the AVT into a rack: • Elevated operating ambient temperature — If the equipment is installed in a closed or multi-u...
AVT 200HD Tuner • Reference Information 100 100 IP Addressing What is an IP Address? An IP address is a 32-bit binary number that is used to identify each device on an Ethernet network. This number is usually represented by four decimal numbers (each in the range or 0 to 255) separated by dots, such...
AVT 200HD Tuner • Reference Information 101 101 The following is an example of an invalid Class C addressing scheme: Device IP Address AVT 200HD Control Software Computer 208.132.180.41 AVT 200HD tuner 192.157.180.42 NOTE: The above addresses are invalid because the network identifier for each addre...
AVT 200HD Tuner • Reference Information 102 102 The line Pinging ... reports the actual numeric IP address, regardless of whether you entered the actual numeric IP address or an alias name. C:\>ping 192.168.254.254 Pinging 192.168.254.254 with 32 bytes of data: Reply from 192.168.254.254: bytes=3...
AVT 200HD Tuner • Reference Information 103 103 Telnet tips It is not the intention of this guide to detail all of the operations and functionality of Telnet; however, some basic level of understanding is necessary for operating the AVT 200HD via Telnet. Connecting to the AVT (Open command) You conn...
AVT 200HD Tuner • Reference Information 104 104 Setting carriage return-line feed Unless commanded otherwise, Telnet transmits a line feed character only (no carriage return) to the connected tuner when you press the <Enter> key. This is the correct setting for SIS communication with the tuner...
AVT 200HD Tuner • Reference Information 105 105 Subnet masks and octets The subnet mask (figure 66) is used to determine whether the local and remote devices are on the same subnet or different subnets. The subnet mask consists of four numeric octets separated by dots. Each octet can be numbered fro...
AVT 200HD Tuner • Reference Information 106 106 Frequency Tables The following tables list all the ATSC (over-the-air) and cable channels that are available through the AVT 200HD. ATSC Frequency Table Physical Channel Lower Edge Video Carrier ATSC Carrier Audio Carrier Upper Edge 2 54 55.25 54.31 59...
AVT 200HD Tuner • Reference Information 107 107 Physical Channel Lower Edge Video Carrier ATSC Carrier Audio Carrier Upper Edge 36 602 603.25 602.31 607.75 608 37* 608 609.25 – 613.75 614 38 614 615.25 614.31 619.75 620 39 620 621.25 620.31 625.75 626 40 626 627.25 626.31 631.75 632 41 632 633.25 63...
AVT 200HD Tuner • Reference Information 108 108 Cable Frequency Table Physical Channel Visual Carrier Frequency (MHz) Standard Cable IRC Cable HRC Cable 2 55.25 55.25 54 3 61.25 61.25 60 4 67.25 67.25 66 5 77.25 79.25 78 6 83.25 85.25 84 7 175.25 175.25 174 8 181.25 181.25 180 9 187.25 187.25 186 10...
Extron USA - West Headquarters + 800.633.9876 Inside USA/Canada Only +1.714.491.1500+1.714.491.1517 FAX Extron USA - East +800.633.9876 Inside USA/Canada Only +1.919.863.1794+1.919.863.1797 FAX Extron Europe +800.3987.6673 Inside Europe Only +31.33.453.4040+31.33.453.4050 FAX Extron Asia +800.7339.8...
Extron Manuals
-
Extron 60-442-01
Manual
-
Extron 88
Manual
-
Extron DVS 304 D
Manual
-
Extron M59-6 BNC
Manual
-
Extron GLI 1000 HD
Manual
-
Extron SI 26
Manual
-
Extron VSC 700
Manual
-
Extron MHR-5P BNC/50
Manual
-
Extron SW8/12 VGA
Manual
-
Extron MAV 84
Manual
-
Extron MDA 5SVA RCA
Manual
-
Extron RS-232
Manual
-
Extron MLS 506SA
Manual
-
Extron MLS 406
Manual
-
Extron IN1608
Manual
-
Extron BNC 5 RC
Manual
-
Extron TPR150
Manual
-
Extron MPX Plus 866 A
Manual
-
Extron CCR 204
Manual
-
Extron WPC 210 A MK
Manual