Extron 80 - Manuals - manualsarea.com

Page 2 - Safety Instructions; Safety Instructions • English; 注意; 注意

Safety Instructions Safety Instructions • English WARNING: This symbol, , when used on the product, is intended to alert the user of the presence of uninsulated dangerous voltage within the product’s enclosure that may present a risk of electric shock. ATTENTION: This symbol, , when used on the prod...

Page 3 - FCC Class A Notice; accessibility, and related topics, see the “; Extron Safety and Regulatory Compliance; ” on the Extron website.; Copyright; © 2014 Extron Electronics. All rights reserved.; Registered Trademarks; Registered Service Mark; Trademarks

FCC Class A Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. The Class A limits provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equ...

Page 4 - Conventions Used in this Guide; Notifications; CE; File; Specifications Availability

Conventions Used in this Guide Notifications The following notifications are used in this guide: CAUTION: Risk of minor personal injury. ATTENTION : Risque de blessure mineure. ATTENTION: • Risk of property damage. • Risque de dommages matériels. NOTE: A note draws attention to important information...

Page 5 - Contents; Introduction; Changing the Output Resolution and Refresh; Remote Configuration and Control; Command and Response Table for SIS; Mounting

Contents Introduction ............................................................ 1 About this Guide ................................................. 1About the DSC HD-HD ....................................... 1Features ............................................................. 1Application Di...

Page 7 - About this Guide; HDMI video cross conversion; DSC HD-HD • Introduction

Introduction This section provides an overview of the DSC HD-HD scaler, covering the following topics: • About this Guide • About the DSC HD-HD • Features • Application Diagram About this Guide The DSC HD-HD User Guide describes the Extron DSC HD-HD Scaler and provides instructions for experienced i...

Page 9 - Application Diagram; Extron; DSC HD-HD Application Example

Application Diagram POWER 12V 0.7A MAX DSC HD-HD HDMI INPUT HDMI OUTPUT LAN 3 2 1 4 3 2 1 MODEL 80 FLAT PANEL Extron XTP CrossPoint 1600 Modular Digital Matrix Switcher Extron DSC HD-HD HDMI to HDMI Scaler VC Codec HDMI 720p Output Resolution 1920x1200 Input Resolution Flat Panel Display 1920x1200 N...

Page 10 - Installation; Rear Panel Connections; Remove power from the system before making any connections.; DSC HD-HD Rear Panel; DSC HD-HD • Installation

Installation This section provides a description of the DSC HD-HD rear panel connectors and instructions for cabling. Topics include: • Rear Panel Connections • Securing the HDMI Connector Using the LockIt Bracket • Connecting for Remote Control • Wiring the Power Connector ATTENTION: • Installation...

Page 11 - Securing the HDMI Connector Using the LockIt Bracket

A Power connector — Connect the provided 12 V, 1 A power supply to this 2-pole captive screw connector (see Wiring the Power Connector on page 8). ATTENTION: • Do not connect power to the unit until you have read the CAUTION and ATTENTION notices on page 8. • Ne branchez pas l’alimentation au l’unit...

Page 12 - Connecting for Remote Control; Computer; Connecting the DSC to the Computer; Power on both the computer and the DSC.; Windows XP and earlier:; If the following screen is displayed, specify whether; Found New Hardware Wizard Opening Screen

Connecting for Remote Control The USB Config port on the front panel enables you to connect the DSC to a computer for configuration and firmware updating via SIS commands or the PCS software: 1. Use a USB A-to-mini-B cable to connect the DSC USB Config port to a USB port on your computer. USB Cable ...

Page 13 - first; Driver Software Installation Window for USB Software

Select one of the following radio buttons, then click the Next button: • Select the Yes, this time only radio button if you want your computer to connect to Windows Update only this one time. • Select Yes, now and every time I connect a device if you want the computer to automatically connect to Win...

Page 14 - Windows XP or earlier:; Finish; Ready; Close; SIS Commands; Wiring the Power Connector; Risk of electric shock.

5. Windows XP or earlier: When the Completed screen appears, click Finish to close the wizard. Windows 7 or later: When the USB software has been located and downloaded, the message Ready to use appears on the Driver Software Installation screen (a pop-up message appears above the Windows taskbar if...

Page 15 - Cut the DC output cord to the length needed.

A 12 VDC, 1 A power supply is provided with the DSC HD-HD. Should it be necessary to attach a 2-pole captive screw connector to your power supply, follow these instructions: Captive Screw Connector Tie Wrap HeatShrink 1/8" (3 mm) 7/8" (22 mm) 3/16" (5 mm) Max. Figure 7. Wiring the Power ...

Page 16 - Operation; Front Panel Features; DSC HD-HD Front Panel; Blinks amber every 3 seconds when the unit is in standby mode.; Config port; off when an unencrypted signal or no active signal is detected.; Output; This green LED lights when embedded LPCM two-channel; DSC HD-HD • Operation

Operation This section discusses the functions available through the front panel and the on-screen display (OSD) to configure and operate the DSC HD-HD. Topics include: • Front Panel Features • On-screen Display • Changing the Output Resolution and Refresh Rate • Locking the Front Panel (Executive M...

Page 17 - Menu Overview; OSD menu table; Device; Using the Front Panel Buttons with the OSD Menus

E Menu and Enter buttons — These buttons enable you to access and make selections from the on-screen display menus (see “Using the Front Panel Buttons with the OSD Menus,” below, for detailed explanations of these buttons and the arrow buttons. F Navigation arrow buttons — These left t , right  , u...

Page 18 - Using the OSD Menus; Input; OSD Main Menu, Initial View

• Up arrow  — Press this button to move upward through main menu and submenu options. This button also adjusts settings for selected submenu options. • Down arrow  — Press this button to move downward through main menu and submenu options. This button also adjusts settings for selected submenu opt...

Page 19 - Example of a Selected Submenu Option; DSC HD-HD OSD Menu System Summary; Submenu; Pixels and lines

Figure 10. Example of a Selected Submenu Option 6. Press the t or  button to adjust the value in the highlighted field. 7. Press Enter to confirm the new values. Press Enter again if action confirmation is requested. The yellow highlighting is replaced by the yellow outline on the menu. 8. Do any o...

Page 20 - Input submenu; table

Input submenu This submenu allows you to perform certain input adjustments and to view the active lines and pixels. Figure 11. Input Submenu (DSC HD-HD) • Film Detect — This option lets you enable and disable Film Detection. After selecting the option, press any arrow button to toggle between On (th...

Page 21 - Input EDIDs; Resolution; Default resolution and rate; Selecting an input EDID; Capture Output EDID; Capturing the output EDID

Input EDIDs Resolution 23.98 Hz 24 Hz 25 Hz 29.97 Hz 30 Hz 50 Hz 59.94 Hz 60 Hz Match Output Rate Match current DSC output resolution (EDID only) 640 x 480 X 800 x 600 X 1024 x 768 X 1280 x 768 X 1280 x 800 X 1280 x 1024 X 1360 x 768 X 1366 x 768 X 1440 x 900 X 1400 x 1050 X 1600 x 900 X 1680 x 1050...

Page 22 - Output Submenu

Output Submenu This submenu allows you to configure the output of the DSC HD-HD. Figure 12. Output Submenu • Output Resolution — This option lets you select the resolution and refresh rate for the connected output display. The DSC HD-HD has a range of resolutions from which to choose (see the EDID t...

Page 23 - HDCP CONTENT; Off; Advanced submenu; Advanced Submenu; Advanced

• HDCP Notification — This option provides a means of determining if HDCP content restrictions are preventing a video signal from passing. The DSC notifies you if you are trying to view HDCP protected content through a non-HDCP compliant HDMI/DVI display. The display shows either of the following: •...

Page 24 - Screen Saver and Timeout; Black; Factory Reset; Factory; Resetting the Unit

NOTES: • The Audio Test pattern displays a crop pattern with AUDIO TEST in a bouncing text box. It also outputs pink noise at 48 kHz, 24 bit. • By default all test patterns include a single pixel wide crop pattern line. • Screen Saver and Timeout — This option lets you enable screen saver mode, in w...

Page 25 - Device Info; Device Info Screen; Changing the Output Resolution and Refresh Rate; In addition to the; Output submenu; Custom Rates; Output Configuration SIS commands; Hz; Importing an HDMI EDID; EDID commands

Device Info Screen This read-only screen provides a quick view of certain selections, parameters, and status information for the DSC. Some of these items are also on other DSC screens. However, the Device Info screen provides them all on a single screen for a system overview. Device Info Figure 15. ...

Page 26 - Resetting the Output Rate; Hold; Factory Reset option

Resetting the Output Rate On the front panel, Hold  for XGA / 720p is printed above the arrow buttons. If an output image cannot be displayed due to an incompatible output rate, you can use the front panel buttons to toggle the output rate between 1024x768 @ 60 Hz and 720p @ 60 Hz. To set the rate ...

Page 27 - DSC-initiated Messages; Reconfig; DSC HD-HD • Remote Configuration and Control

Remote Configuration and Control This section describes the connections through which the DSC can be configured and controlled remotely via SIS commands and describes the commands that are available. Topics include: • SIS Commands • Windows-based Configuration Program The DSC can be configured and c...

Page 28 - Command and Response Table for SIS Commands; ASCII to HEX Conversion Table; ASCII to Hexadecimal Character Conversion Table; Symbol Definitions; = Carriage return with line feed

Error Responses When the DSC receives a valid command, it executes the command and sends a response to the host device. If the unit is unable to execute the command because the command contains invalid parameters, it returns an error response to the host. This code is displayed on the host interface...

Page 32 - HDCP Authorization; Film Detection; In verbose modes 2 and 3:; Aspect Ratio; In verbose modes 2 and 3:; Output Resolution; Set output rate

Command and Response Table for SIS Commands Command ASCII Command (Host to Scaler) Response (Scaler to Host) Additional Description Input Configuration HDCP Authorization On E E 1 * 1 HDCP } Hdcp E 1 * 1 ] Enable HDCP encryption support for the input (default). Off E E 1 * 0 HDCP } Hdcp E 1 * 0 ] Di...

Page 33 - Always encrypt output:; Digital Output Format; View output format

Command ASCII Command (Host to Scaler) Response (Scaler to Host) Additional Description Output Configuration (continued) Output HDCP Mode Set HDCP mode E S X% HDCP } Hdcp S X% ] Set the HDCP mode to X% . For X% : 0 = Follow input: HDCP is always authenticated but encrypted only when required. 1 = Al...

Page 34 - HDCP Encryption Status

Command ASCII Command (Host to Scaler) Response (Scaler to Host) Additional Description Output Configuration (continued) Video Mute (Defaults to unmuted after a power cycle.) Mute video to black 1B Vmt1 ] Mute video to a black screen. Mute sync and video 2B Vmt2 ] Mute video and sync on the output. ...

Page 35 - Audio Mute (Global setting — persists after a power cycle); Audio Input Format; HDCP Notification

Command ASCII Command (Host to Scaler) Response (Scaler to Host) Additional Description Audio Configuration Audio Mute (Global setting — persists after a power cycle) Mute on 1 Z Amt 1 ] Mute the audio on the output. Mute off 0 Z Amt 0 ] Unmute the audio. View mute status Z X! ] In verbose modes 2 a...

Page 36 - Test Pattern; Video Signal Presence; View signal presence; For

Command ASCII Command (Host to Scaler) Response (Scaler to Host) Additional Description Advanced Configuration (continued) Test Pattern Set test pattern E X& TEST } Test X& ] Select test pattern X& . For X& : 0 = Off (default) 1 = Crop 2 = Alternating pixels 3 = Crosshatch 4 = Color ...

Page 37 - View; Verbose Mode

Command ASCII Command (Host to Scaler) Response (Scaler to Host) Additional Description Information Requests (continued) Query firmware build version * Q n.nn.nnnn ] In verbose modes 2 and 3: Bld n.nn.nnnn ] View full firmware version details. Query boot loader version, factory firmware version, and...

Page 38 - Windows-based Configuration Program; Downloading the PCS Configuration Software from the Website; Open the Extron web page and select the; Download; On the Download Center screen, click the; PCS; link on the left sidebar menu (see; Software Links on the Download Page of the Extron Website

Windows-based Configuration Program The Extron Product Configuration Software (PCS) is a Windows-based program for the DSC that provides a convenient way to configure the input and output, audio, and image settings. It lets you perform nearly all the other functions that can be accomplished via the ...

Page 39 - On the PCS page, click the; Downloads; button near the center of the page (see; Downloads Button on the PCS Web Page

3. On the PCS page, click the Downloads button near the center of the page (see figure 18). Figure 18. Downloads Button on the PCS Web Page DSC HD-HD • Remote Configuration and Control 33

Page 40 - PCS Software Link on PCS Web Page

4. On the next PCS page, click the PCS link, located near the bottom of the page. Figure 19. PCS Software Link on PCS Web Page The Download Center screen appears. 5. On the Download Center screen, fill in the required information, then click the Download pcss_v n x n .exe button. 6. If the File Down...

Page 41 - or; Starting the Configuration Program; Files; Device Discovery Panel with DSC HD-HD Selected

8. Follow the instructions on the InstallShield Wizard screens to complete the software program installation. By default the installation creates a folder called “Extron PCS” in the following location on the computer: c:\Program Files (x86)\Extron\Extron PCS (for Windows 7 and later) c:\Program File...

Page 42 - On the main window, click the; and select; DSC; from the drop-down menu for the procedures for; PCS Menu Icon on the PCS Main Window

5. On the main window, click the PCS menu icon in the upper-right corner (see figure 21), and select DSC HD-HD Help from the drop-down menu for the procedures for connecting to the DSC and configuring it. Figure 21. PCS Menu Icon on the PCS Main Window DSC HD-HD • Remote Configuration and Control 36

Page 43 - Elevated operating ambient temperature

Mounting This section contains information on mounting the DSC scaler. See www.extron.com for available Extron mounting kits and ordering information.The DSC HD-HD scalers can be mounted by any of the methods listed below. To mount the DSC using an Extron mounting kit, see the instructions provided ...

Page 44 - Contact Information; USA; xtron

Extron Headquarters +1.800.633.9876 (Inside USA/Canada Only)Extron USA - West Extron USA - East +1.714.491.1500 +1.919.850.1000 +1.714.491.1517 FAX +1.919.850.1001 FAX Extron Europe +800.3987.6673 (Inside Europe Only)+31.33.453.4040 +31.33.453.4050 FAX Extron Asia +65.6383.4400+65.6383.4664 FAX Extr...