Extron 68-498-01 - Manuals

i System 5 cccccrrrrr Plus • Table of Contents Table of Contents Chapter 1 • Introduction ....................................................................................................... 1-1 About this Manual .......................................................................................

ii System 5 cccccrrrrr Plus • Table of Contents Table of Contents, cont’d Control Software for Windows .................................................................................... 4-6 Installing the software .......................................................................................

System 5 cccccrrrrr Plus 1 Chapter One Introduction About this Manual About the System 5 cr Plus Features and Options

Introduction, cont’d System 5 cr cr cr cr cr Plus • Introduction 1-2 Introduction About this Manual This manual discusses how to install, operate and configure the ExtronSystem 5 cr Plus switcher and how to operate the IR 401 infrared remote control that is included with the System 5 cr Plus. For in...

1-3 System 5 cr cr cr cr cr Plus • Introduction IR commands for the projector can be associated with each of the Display buttons(Power, Mute, and Mode) on the front panel, as well as with each of the five inputbuttons (PC 1, PC 2, Input 3, Vid 1, and Vid 2). POWER MUTE DISPLAY SCP 100P MODE VOLUME A...

Introduction, cont’d System 5 cr cr cr cr cr Plus • Introduction 1-4 Features and Options Features 250 MHz (-3dB) video bandwidth Five video inputs — • 2 RGBHV/RGBS/RGsB computer video inputs — A VGA 15-pin HD front panel connector (PC 1) allows direct connection of a laptop computer, andone set of ...

1-5 System 5 cr cr cr cr cr Plus • Introduction 50/60 Hz 100-240V 1.3A RS-232 R G B PC 2INPUT 3 VID 1VID 2 H/HV V R G B H/HV V L R R G/Y B/C H/HV V V/Y V/Y C C Y C VID LINE OUT L R L R L R L L R R L R AUX 1 AUX 2 AMPLIFIED OUT DISPLAY PWR SENSOR RELAY COMM. Room Control Rear To Second Control Pad SC...

System 5 cccccrrrrr Plus 2 Chapter Two Installation Mounting the Switcher Cabling and Panel Views

Installation, cont’d System 5 cccccrrrrr Plus • Installation 2-2 TX RX IR LEARN CONFIG RETRY COMPUTER AUDIO PC1 INPUT Plus SYSTEM 5 Installation Mounting the Switcher The System 5 cr Plus comes with two sets of mounting brackets. One set is for mounting the switcher under a table or on (against) a w...

2-3 System 5 cccccrrrrr Plus • Installation To wire the PC 1 audio input plug, follow the wiring diagram shown below. Tip (+) Sleeve (GND) Tip (L, +) Ring (R, -) Sleeve (GND) PC1 audio input plug wiring Rear panel inputs 1 AC power connector — Plug a standard IEC power cord into this port to connect...

Installation, cont’d System 5 cccccrrrrr Plus • Installation 2-4 RS-232 R G B H/HV V Y C VID LINE OUT L L R R L R AUX 1 AUX 2 AMPLIFIED OUT DISPLAY PWR SENSOR RELAY COMM. ABCDE OU TP U TS 3 1 2 5 4 4 Vid 1 and Vid 2 composite/S-video inputs — Connect the cables as shown here. For S-video, connect th...

2-5 System 5 cccccrrrrr Plus • Installation This output provides 24 watts of power (12 watts per channel with a 4 ohmload) or 12 watts ( 6 watts per channel with an 8 ohm load). The output levelvaries depending on the front panel volume adjustment. Control device connections Captive screw and 3.5 mm...

Installation, cont’d System 5 cccccrrrrr Plus • Installation 2-6 3 Display power sensor port — This mini stereo-style jack allows connection of an optional display power (current) sensor (Extron part #60-271-01). Thepower sensor is used to keep the projector and the System 5 in sync. Refer tothe Pow...

System 5 cccccrrrrr Plus 3 Chapter Three Operation Front Panel Controls and Indicators Setting Up the System 5 cr Plus Remote Control of the System 5 cr Plus

Setup and Operation, cont’d System 5 cccccrrrrr Plus • Setup and Operation 3-2 Setup and Operation Front Panel Controls and Indicators VID MAX. CLIP MIN. TX RX IR LEARN CONFIG RETRY Y/C VID PC Y/C VID Y/C ROOM DISPLAY POWER MUTE MODE PC1 PC2 INPUT 3 VOLUME AUDIO COMPUTER AUDIO PC1 INPUT Plus SYSTEM ...

3-3 System 5 cccccrrrrr Plus • Setup and Operation lights. If the System 5 has learned commands, it may send IR commands (such as adisplay mode change command) to the projector when an input is selected. 6 PC 1 and PC 2 — Press these buttons to select input 1 (PC 1, front panel) or input 2 (PC 2, re...

Setup and Operation, cont’d System 5 cccccrrrrr Plus • Setup and Operation 3-4 Setting Up the System 5 cccccrrrrr Plus The System 5 cr Plus must be set up (configured) before it can control other equipment. Setup can be done from the front panel, or from a computer using theprovided control software...

3-5 System 5 cccccrrrrr Plus • Setup and Operation Setting audio input attenuation levels Before setting the audio levels, ensure that all the audio input sources are activeand connected to the System 5. To set the audio levels, see the following flowchart. Press and hold all 3 DISPLAY buttons toget...

Setup and Operation, cont’d System 5 cccccrrrrr Plus • Setup and Operation 3-6 Initiating IR learning The System 5 can “learn” control commands from projectors’ remote controls.IR learning is only necessary if there is no IR driver available for that projector or ifthe driver is not complete. The Sy...

3-7 System 5 cccccrrrrr Plus • Setup and Operation Remote Control of the System 5 cccccrrrrr Plus The System 5 can be controlled by using its front panel controls, the includedIR 401 infrared remote control, optional SCP remote control panels, or anRS-232 control device or computer. The IR 401 and S...

System 5 cccccrrrrr Plus 4 Chapter Four Serial Communication RS-232 Programmer’s Guide Control Software for Windows

Serial Communication, cont’d System 5 cccccrrrrr Plus • Serial Communication 4-2 Serial Communication The System 5 cr Plus can be remotely controlled via a host computer or other device (such as a control system) attached to the rear panel RS-232 connector. The controldevice (host) can use either Ex...

4-3 System 5 cccccrrrrr Plus • Serial Communication The error response codes and their descriptions are as follows: E01 – Invalid input channel number (the number is too large)E10 – Invalid commandE13 – Invalid value (the number is out of range/too large)E16 – Unit is busyE23 – Checksum error. Using...

Serial Communication, cont’d System 5 cccccrrrrr Plus • Serial Communication 4-4 Command/response table for SIS commands Command description Command Response Additional ASCII Hex (switcher to host) description Input selection Select both video and audio X1 ! 30 + X1 21 C X1 Video & audio input X...

4-5 System 5 cccccrrrrr Plus • Serial Communication Flag block The flag block consists of fifteen bytes (0 to 14) that will be used for handlingspecial operation functions. Byte 0 – Power on delayByte 1 – Power off delayByte 2 – Triple-action switching delay (0.5 second * value)Byte 3 – Relay contro...

Serial Communication, cont’d System 5 cccccrrrrr Plus • Serial Communication 4-6 Control Software for Windows Installing the software The included graphical control software for Windows offers another way to controlthe System 5 via RS-232 connection in addition to the Simple Instruction Setcommands....

4-7 System 5 cccccrrrrr Plus • Serial Communication Power-up/down delay, room relay mode, auto-set attenuators, RGB delay, andmiscellaneous options are adjustable only via the Configure Unit control screen.Refer to the System 5cr Help program for details on setting these options. Power Up/Down Delay...

Serial Communication, cont’d System 5 cccccrrrrr Plus • Serial Communication 4-8 Using the help program For information on program features, press the F1 computer key, or click on the Help menu from within the System 5cr control program, or double-click onthe SYSTEM 5cr Help icon in the Extron Elect...

System 5 cccccrrrrr Plus A Appendix Appendix Specifications Part Numbers and Accessories Firmware Upgrade Installation Glossary

Appendix, cont’d System 5 cccccrrrrr Plus • Appendix A-2 Appendix Specifications Video Gain ............................................... UnityBandwidth .................................... 250 MHz (-3dB)Frequency response ..................... < ± 0.1dB @ 30 MHzDifferential phase error ..........

A-3 System 5 cccccrrrrr Plus • Appendix Audio Gain ............................................... Unbalanced/balanced -78dB to +40dBFrequency response ..................... 20 Hz to 20 kHz, ±0.05dBTHD + Noise ................................ <0.1% @ 1 kHz at rated maximum output driveS/N ..........

Appendix, cont’d System 5 cccccrrrrr Plus • Appendix A-4 Part Numbers and Accessories Included parts These items are included in each order for a System 5 cr Plus switcher: Included parts Part number System 5 cr Plus 60-269-02 Rack mounting bracket kit 70-077-03 Table mounting bracket kit 70-077-01 ...

A-5 System 5 cccccrrrrr Plus • Appendix Firmware Upgrade Installation In some cases the System 5’s firmware may require replacement with an updatedversion. The two user-replaceable firmware chips are U1, the main microcontroller,and U7, the carrier signal generator. Changes to firmware must be perfo...

Appendix, cont’d System 5 cccccrrrrr Plus • Appendix A-6 Glossary Attenuate/attenuation — To reduce the amplitude (strength) of a signal or current. Balanced audio — A method that uses three conductors for one audio signal. They are plus (+), minus (-), and ground. The ground conductor is strictly f...

A-7 System 5 cccccrrrrr Plus • Appendix Latching — The System 5 room relay can operate in two modes: latching or momentary. In the latching mode, the relay remains active (latched) until it ismanually reset (unlatched). Level — The relative intensity (strength, voltage, volume) of an audio or video ...

Extron’s Warranty Extron Electronics warrants this product against defects in materials and workmanship for a periodof three years from the date of purchase. In the event of malfunction during the warranty periodattributable directly to faulty workmanship and/or materials, Extron Electronics will, a...