Extron 305SA - Manuals

Introduction Overview This guide covers the installation of the Extron PoleVault IP System in a drop ceiling room with a wood or concrete structural ceiling. If the location has a concrete or beam style ceiling, alternative ceiling mounts can be obtained separately from Extron. It is assumed that th...

PVS 305S A POL EVAU LT SWITCHE R INPUT SELECTION 1 2 PEA K NOR MA L SIGNAL CONFIG 3 4 5 AUX AUDI O AUDIO LEVEL ADJUST PAG ING SEN SOR SEN SITIV ITY VOIC ELIFT MIC PEA K NOR MA L SIG NAL INPU T L S G AUDIO IN VIDEO IN IR O UT R COMPUTER IN AUD IO IN OUT MONITOR OU T IR OUT S G TCP/IP Network RS-232 t...

Before You Begin — Planning the Installation Before installation is started, you must be consider several major factors to ensure that the installation process is as smooth and trouble free as possible, and so that the final finished project meets the needs of the customers, users, audiences, and in...

• Ceiling and wall type (important in assessing the hardware needed) • Ceiling type: dropped, spline, hard lid and similar. Structural type (wood, concrete, trusses), plenum or non-plenum • Wall type: drywall, cement, brick. WARNING: Structural ceiling failure could cause death serious injury or dea...

c. Location of MediaLink® Controller and Wall Plates • Forward and side reach (for full details refer to a copy of ADA Standards for Accessible Design, Sections 307 and 308, for ADA requirements) . • Location of source devicesDesk, table, or rack mounted, and proximity to proposed transmitter locati...

Inventory Included Items The PoleVault IP System (featuring the PVS 305SA IP switcher) ships in one box. The box (80-xxx-13) contains the devices, hardware, and FF 120 speakers.Carefully check all the received items against the lists on this and the next page. PoleVault IP System 80-200-13 (or 80-30...

PoleVault IP System 80-200-13 (or 80-300-13*, 80-400-13*) MLC 104 IP Plus White 60-818-03 MLC 104 IP Plus PVS 305SA IP 60-986-01N PVS 305SA IP PoleVault IP Switcher (1) 2-pole connector(1) 3-pole connector (3) 5-pole connector(1) Audio connector, 4-pole (2) Securing screws(5) Tie wraps PVS 305SA IP ...

Installation Overview This overview outlines the basic steps for installing the PoleVault IP System. An outline and checklist of the stages (Stages One through Five), listing the relevant steps within each stage, is given on page 10 and rear cover.A fully detailed description of these steps is given...

Outline of Installation Steps Stage 1 — Install the Screen and Projector c Mark the screen location (page 12) . c Install projector to verify location (page 12 ). c Verify the image location (page 15) . c Cut the ceiling tile (page 16) . c Preliminary safety hardware installation (page 16) . c Finis...

PCM 340 Projector Drop Ceiling Mount a • Where it goes: Attaches to a structural ceiling, rests on the suspended ceiling. • What it does: Holds the slotted pipe, PoleVault pole mount kit (PMK 550), and projector. Slotted Pipe b • Where it goes: Locks into place in the PCM 340 pipe adapter. • What it...

ï Screw the adjuster plate onto the base of the pipe. d. Using a 3/32 inch hex wrench, back out the set screws on the top portion of the adjuster plate (see a in the image below) of the UPB 25. Screw the plate onto the base of the pipe. Align it so the security flange is at the rear Adjuster PlateLo...

Using the slot closest to the barrel , secure the arms to the bracket with the clamp and screw. vi. Pivot the arms so that they extend towards the center of the projector (see the figure at right). Adjust the arms as needed for your projector model. NOTE: Avoid overlapping the arms where possible. v...

ix. Check for stress on the arms. To do this loosen the mounting screws (do not remove). If the arm or the barrel lifts, this indicates stress on the arm. Adjust the height of the threaded barrels to reduce or eliminate any torque or stress that might be caused by crossed arms or by projector mounti...

à Mark the structural ceiling for lag eye bolt installation. 4.— Cut the Ceiling Tile a. Mark the location of the PCM 340 on the T-frame. This aids putting it back in the correct location when the tile is replaced. TIP: Mark the screen direction on back of the tile (for example with an arrow or “to ...

å Attach the turnbuckles at the corners of the PCM 340. 7. — Secure the Projector Drop Ceiling Mount to the Ceiling a. Attach the four turnbuckles to the mounting plate, one at each corner. WARNING: May result in serious injury. DO NOT rest or lean on the mounting plate or suspended ceiling when att...

8. — Install the Electrical Box (if required) WARNING: Improper installation may result in electrical shock or serious injury. All electrical installation should be performed by qualified personnel in accordance with local and national building codes, fire and safety codes, and local and national el...

COMPUTER IN AUDIO IN OUT MONITOR OUT IR OUT S G Audio and VideoOutput Port (at rear) PVT CV D AUDIO IN L R VIDEO IN IR OUT S G DecoraFaceplate MountingScrews (2) IR Output IR InputConnector(at rear) IR InputConnector(at rear) Line OutAudio Connector(at rear) Audio and VideoOutput Ports (2** at rear)...

CONFIG DISPLAY VOLUME MLC 104 IP PLUS ON VCR DVD PC OFF 1 2 3 4 Mountingscrews (4) 123 G R O U N D + 1 2 V O U T C M G RO U N D I R O U T G R O U N D S C P G RO U N D T xR x DISPLA Y RS-232/IR A B C D E COMM LINK LAN PRESS TAB WITH TWEEKER TO REM OV E A B MLS RS-232 PO WER 12V DIGIT AL I/O I R I N T...

NOTE: The installation must conform to national and local building and electrical codes, and UL requirements. See the device user guides for details. 1. — Install the Mud Rings NOTE: These devices can be installed using the supplied mud ring or a wall box. If installing a box, allow enough depth for...

2. — Pull the Cables (at the input locations) The following cables need to be installed: • CAT 5 cables for signal transmission from the AV wall plates to the PVS 305SA IP NOTES: • For PVT RGB D IP Plus four CAT 5 cables (two for video input and two for LAN) are needed, and for PVT RGB D wall plates...

3. — Install Wall Plates a. Connect the CAT 5 cables to the rear of the input devices (for RGB devices, connect cable labeled A to port A and cable B to port B). For PVT CV D plates connect the single cable to the device. b. Run LAN cables (included) to the rear of the PVT RGB D IP Plus, and connect...

4. — Install MediaLink Controller TIP: Before cabling and installing the MLC 104 IP Plus, locate and write down the MAC address of the device for configuring the IP address. The 12 character alphanumeric address (for example, 00-05-A6-03-9G-H4) can be found on a label on the side of the controller. ...

b. Connect the IR/RS-232 projector communication cable as shown for either RS-232 or IR projector control NOTE: Some projectors require NULL connection wiring, which inverts the Tx and Rx connections. See the projector guide for details. c. Connect a network cable (CAT 5, 5e, or 6 straight through) ...

d. The connections between the MLC 104 IP Plus and the PVS 305SA IP switcher should look like the figure at right. e. Sliding the cables into the opening, secure the MLC 104 IP Plus to the mud ring with the provided machine screws. 4.06" 3.75" Wall Mouting Bracket Rotate locking arm and inse...

Stage 3: Installing the FF 120 Ceiling Speakers Stage 3 Involves Installing the Devices Shown Below. • Where it goes: Installs in ceiling tiles at predetermined location for best acoustics. Connects to switcher. • What it does : Receives and outputs audio signal from the PVS 305SA IP switcher. FF 12...

3. — Terminate the Speaker Cable for the PVS Switcher a. To terminate the cable, strip the end of the cable 0.2 inch (5 mm) and secure the wires into the supplied 4-pole captive screw connector. ATTENTION: DO NOT short the speaker wires together as it may damage the switcher. NOTE: The correct speak...

Stage 4: Installing the PMK 550 and the PVS 305SA IP Stage 4 Involves Installing the Devices Shown Below. L R L R L R AUX AUDIO INPUT 5 LINE OUT VOICELIFT RECEIVER PAGING SENSOR DO NOT GROUND OR SHORT SPEAKER OUTPUTS 1B RGB 1A RGB 2B RGB 2A RGB 3B RGB /VIDEO 4B RGB /VIDEO 3A RGB 4A RGB I NPUTS RS-23...

NOTES: • The installation must conform to national and local building and electrical codes, and UL requirements. See the device user guide for details. • The included power supply MUST NOT be installed above the suspended ceiling, in wall cavities or similar locations. 1. — Install the PMK 550 Base ...

2. — Pull the Cables (at the Switcher location) a. Gather all the cables from the speakers, AV wall plates, MLC 104 IP Plus controller, and any installed optional devices that have been run to the switcher location. Pull them down through the ceiling hole and the pipe. These cables are: • the MLC po...

3. — Finish installing the Pole Mount Kit CAUTION: The PoleVault signal transmission method is specific for PVS 305SA IP switchers working with PVT wallplates. DO NOT connect the input ports to an MTP system or to an LAN or data transmission system. LAN LAN L R L R L R AUX AUDIO INPUT 5 LINE OUT VOI...

The MLS Configuration Utility software û Launch the MLS Configuration program ü Select “Help, Contents” and follow instructions Stage 5: Configuring the PVS 305SA IP Switcher Stage 5 Involves Installing the Programs Shown Below. Items needed to help complete this stage: • Laptop (or PC) with a netwo...

2. — Configure the System — Global Configurator a. Download and install Extron’s Global Configurator (GC) configuration program (available at www.extron.com ) on the laptop or PC. b. Ensure the PC and the MLC 104 IP Plus are connected to the LAN. NOTE: Alternatively, connect a 2.5 mm TRS configurati...

3. — Test the System a. Connect all the input devices (PC, DVD, document camera, and where desired LAN cables, and so forth) to the transmitters and power up the input devices. Check that power and signal are present at the transmitters. The LEDs light red when only power is present and light green ...

d. Test the controller configuration as follows: • Check that the MLC is controlling the projector and PVS 305SA IP switcher, and outputs the correct image when switching inputs. • Check the projector power control (turn it off and on at the MLC). • Adjust the configuration as necessary. e. Adjust t...

EDID Minder The PVT RGB D IP Plus (EDID) and the PVT RGB D (EDID) incorporates EDID Minder, which allows the transmitter to communicate the appropriate EDID information to the source, ensuring correct video output resolution.The 5-pole EDID Minder settings DIP switch is located on the rear of the wa...

Using Learn Mode (Available on PVT RGB D Plus only) 1. Disconnect any sources from the front panel and remove the wallplate from the wall. 2. On the rear panel, set all the DIP switches to off (down). 3. Temporarily connect the main display device (the projector) to the Monitor Out port. 4. On the f...

b Attach the Z bracket to the ceiling tile and the back plate. g Align the arrows on the housing rim and the dome tab. Arrow ReceiverDome Twist toLock Align Arrows Arrow Dot Tab Tab i Plug VoiceLift cable into PVS 305SA IP. Optional Accessory Installation — VoiceLift System The Extron VoiceLift syst...

Open the Page Sensor Ceiling Mounted Paging Speaker PriorityPageSensor Strip plenum jacket fromspeaker cable to revealtwo speaker wires. Speaker Cable withPlenum Jacket Intact d Open the sensor and loop a wire around the sensor. b UL-Compliant Junction Box and Cover Optional Accessory Installation —...

Extron Warranty Extron Electronics warrants this product against defects in materials and workmanship for a period of three years from the date of purchase. In the event of malfunction during the warranty period attributable directly to faulty workmanship and/or materials, Extron Electronics will, a...