Exmark LAZER AS - Manuals

Safety DANGER There are rotating blades in the blower andunder the mower deck. Blade contact cancause serious operator or bystander injuryor even death. • Do Not reach into blower unless rotationindicator has stopped. Disengage PTO,stop engine, remove key, wait for allmoving parts to stop. Engage pa...

Safety Figure 3 1. Safe Zone-Use the mower here on slopes less than 15degrees 2. Danger Zone-Use a walk behind mower and/or handtrimmer on slopes greater than 15 degrees, neardrop-offs and water. 3. Water • Remove or mark obstacles such as rocks, treelimbs, etc. from the mowing area. Tall grass canh...

Safety Safety and Instructional Decals • Keep all safety signs legible. Remove all grease,dirt and debris from safety signs and instructionallabels. • Replace all worn, damaged, or missing safetysigns. • When replacement components are installed, besure that current safety signs are affixed to there...

Specifications Specifications Model Numbers Serial Nos: 790,000 and Higher LZUV2B–Fits Lazer Z (LZZ) and Lazer Z AS (LZAS) with 48 or 52 inch deck. LZUV3B–Fits Lazer Z (LZZ) and Lazer Z AS (LZAS) with 60 or 72 inch deck. Systems Bagging System • Collection bins: – Commercial grade, cloth mesh bags w...

Operation Product Overview Figure 4 1. Hopper 4. Blower 2. Toeboard weight 5. Tube 3. Caster weight (LZUV3BUnits Only) 6. Bag Operation Note: Determine the left and right sides of the machine from the normal operating position. Important: For Serial Numbers 790,000 and higher, multiple accessories a...

Operation CAUTION The deck sheave will become very hot.Touching a hot deck sheave can cause severeburns. Allow the deck sheave to cool completelybefore removing the belt. 5. Pull the idler release handle and remove the belt from the upper groove of the deck sheave. 6. Unlatch the front end of the bl...

Operation the toe board, remove the two hairpins that retainit and then lift it from the mount bracket. Thebracket bolted to the toe board remains on theunit. For the LZUV3B Units: Remove the caster weights by loosening the clamping knobs until theweight can be moved relative to the caster arm.Remov...

Operation Figure 14 Large Decks — View from Top of Blower 1. Impeller sheave 3. Spring loaded idler 2. Deck sheave 17. Position the belt cover at an angle and slide it under the mower frame (see Figure 15). Figure 15 1. Blower 3. Mower frame 2. Belt cover 18. Push down on the back of the cover and s...

Operation tube to provide minimum obstruction to flow.Make sure that the upper and the lower ends areoriented properly as the tubes are assembled.(Parting lines should roughly be lined up.) Figure 18 1. Drill the holes here 28. Slide the lower end of the tube assembly over the blower outlet and alig...

Operation has all necessary lighting and marking as required bylaw. Secure a trailer with a safety chain. CAUTION This unit does not have proper turnsignals, lights, reflective markings, or aslow moving vehicle emblem. Driving on astreet or roadway without such equipmentis dangerous and can lead to ...

Operation Important: The roll bar is an integral and effective safety device. Keep the roll bar in theraised and locked position when operating themower. Lower the roll bar temporarily only whenabsolutely necessary. Refer to the Operator’s manual supplied with yourtractor for additional ROPS safety ...

Maintenance Maintenance Note: Determine the left and right sides of the machine from the normal operating position. WARNING While maintenance or adjustments are beingmade, someone could start the engine.Accidental starting of the engine couldseriously injure you or other bystanders. Remove the key f...

Maintenance Check Exhaust Diverter Service Interval: Before each use or daily CAUTION The exhaust diverter is hot. Touching a hotexhaust diverter can cause severe burns. Allow the exhaust diverter to cool completelybefore performing maintenance. 1. Stop engine, wait for all moving parts to stop, and...

Maintenance Cleaning Clean Muffler and RearFrame Area Service Interval: Before each use or daily Stop engine, wait for all moving parts to stop, andremove key. Engage parking brake. WARNING Operating engine parts, especially themuffler, become extremely hot. Severe burnscan occur on contact and debr...

Troubleshooting Troubleshooting Important: It is essential that all operator safety mechanisms be connected and in proper operating condition prior to mower use. When a problem occurs, Do Not overlook the simple causes. For example: starting problems could becaused by an empty fuel tank. The followi...

Conditions and Products Covered Exmark Mfg. Co. Inc. and its affiliate, Exmark Warranty Company, pursuant to an agreement between them, jointly warrant on the terms and conditions herein, that we will repair, replace or adjust any part on these products and found by us (in the exercise of our reason...

Service Record Date: Description of Work Done: Service Done By: 26

M I D - M O U N T R I D I N G AC C E S S O R I E S A N D O P T I O N S SEE EXMARK’S COMPLETE LINE OF ACCESSORIES AND OPTIONS WALK-BEHIND ACCESSORIES AND OPTIONS GRASS CATCHER MICRO-MULCH SYSTEM TURF STRIPER STANDON CUSTOM RIDE SEAT SUSPENSION SYSTEM FULL SUSPENSION SEAT DECK LIFT ASSIST KIT HITCH KI...