England's Stove Works 10-CDV - Manuals

UNIT PREPARATION 1. Attach the spring handle to the door by turning it counterclockwise. Important: Also check hopper latch – must be tight so that the top is sealed to prevent back-burn. 2. Test your 110-volt outlet for current and then plug in the unit. ( We highly recommend a surge protector for ...

6 • Corn must be clean and free from debris; never burn corn strait from the field. Stalk parts, excessive fines and cob remnants, etc. will clog the auger mechanism. We highly recommend the use of a sifter; sifters to filter your corn are available from dealers (and we offer a sifter at www.england...

Notes on termination of Vent Pipe (see also “FLUE SYSTEM” section of manual): 1. Not less than three (3) feet above any forced air inlet located within ten (10) feet. 2. Not less than four (4) feet below, four (4) feet horizontally from, or one (1) foot above any door, window or gravity air inlet in...

8 • Distance from bottom of termination and grade - one foot (1 ft.) minimum. This is conditional upon the plants and nature of the grade surface. The exhaust gases are hot enough to ignite grass, plants, shrubs, etc. located in the vicinity of the termination. The grade must not be a lawn. Distance...

9 BURNING SOLID FUELS Ashes will need to be removed from the unit periodically. See Ash Removal section. You can minimize cleaning required and maximize efficiency by maintaining the proper draft. This unit has been designed to burn dry shelled corn or premium hardwood pellets that meet the associat...

FLUE SYSTEM Caution: Follow the pipe manufacturer’s installation instructions and directions for passing through combustible walls and ceilings. Be sure to check local codes in your area. NOTE: See the installation drawing later in this manual (Illustration 1). This unit is equipped with a negative ...

Through the Ceiling When venting the stove through the ceiling, the pipe is connected the same as through the wall, except the clean out tee is always on the inside of the house, and a 3” adapter is added before the clean-out tee. You must use the proper ceiling support flanges and roof flashing sup...

1. If 3” flue pipe exceeds 15’ in length, increase to 4” flue pipe for remaining flue connections. 2. Total flue length should not exceed 35’. 3. Horizontal run not to exceed 4’. 4. Floor protector required: Min. size 36” x 36”. 5. If the total run of outside air connection exceeds 6’, if more than ...

13 OPERATING INSTRUCTIONS CAUTION: DO NOT OPERATE WITH THE DOOR OPEN. If door is left open (approximately) two minutes, unit will stop feeding and fire will go out. Do not burn trash (paper bags, etc.) in this unit. This stove has an induced draft system and is designed to operate continuously, as f...

CORN START-UP PROCEDURE When starting the stove with corn, push the “AIR ON TEMP” button and hold, which will rotate the stirrer mechanism in the burn pot. Release the button when the stirrer is strait up (in the “12:00” position) before following the above instructions concerning placing the handfu...

15 E-Codes “E-Codes,” or Error Codes, are codes that will appear in the Heat Range and Blower Speed windows of the Control Board if your unit experiences problems. If you receive these codes, wait until the unit is cooled completely down before trying to restart your unit. If the unit continues to d...

16 DAILY OPERATION Refueling the Unit Always press the “OFF” touch pad before refueling. This stove has a approximately 80-lb. hopper, and should be refilled when the hopper level drops to three or four inches. Note : The hopper lid will be warm; therefore, you should always use some type of hand pr...

17 ASH REMOVAL AND DISPOSAL IMPORTANT: While the amount of ash generated by this unit is not excessive compared to log-burning woodstoves, keeping the unit clean and free of ash is essential for peak performance. Too much ash build-up hampers airflow and reduces the unit’s efficiency, and can cause ...

18 MAINTENANCE CAUTION: UNPLUG THE UNIT PRIOR TO ANY SERVICE WORK! SEE EXPLODED DIAGRAM ( ILLUSTRATION 6 ) FOR PARTS REFERENCE Note: To do any service on this unit the rear access sheet metal panel must be removed. One (1) screw holds this panel to the rear of the stove. Parts Orders: (800) 516-3636...

Finish This new unit has been painted with High-Temperature Paint that should retain its original look for years. If the unit should get wet and rust spots appear, the spots can be sanded with plain steel wool and repainted. We recommend this paint, as others may not adhere to the surface or withsta...

Control Board The Control Board (Part # CU-CB05 ) is a digital read-out board. This board offers a wide variety of settings to operate the unit. This part can be removed from the unit by loosening the two outside screws and pulling the board back to the inside of the stove. The rear access panel sho...

CIRCUIT BOARD FUNCTIONS COMPONENT OPERATION START OPERATION END Exhaust Blower Starts Immediately Will continue until shutdown. Shutdown will occur when the operating temp. is below 90 degrees. Agitator Three minutes after starting, the agitator will begin to turn. Will continue intermittently, as d...

22 ACCESSORY ITEMS The following accessories can be added to your unit at anytime after purchase; however, let the unit cool down before adding any accessories. Thermostat WALL: An external wall thermostat (such as our Part # GU-1E30-914 ) can be used on our corn/pellet units as long as it is a low-...

REPLACEMENT PARTS, ACCESSORIES AND OPTIONS ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 PART NUMBER CA-13C AC-G10 AC-GGK AC-DGKNC CU-GS CU-CFB CU-BP CA-FS CU-SC CA-DS CU-MC CU-AFC CU-RCP CU-047042 CU-CB05 CU-VS CU-AP CU-BR PU-103-50 PU-CBG PU-0760...

Corn Stove – Exploded View Diagram (Illustration 6) 24

Adjusting your Hopper Lid Latch The seals around the top of the pellet hopper are important to safe an efficient operation of the unit. The latch installed on these units is designed to pull the hopper lid tight against this seal. Over the course of operation as these seals “wear in” and compress, t...

Ash Pan Latch Illustration 8 Dimensions of your corn/pellet unit: 28”W x 33”H x 28”D 350 lbs. (Approx.18” height from floor to center of exhaust) Illustration 9 Base Options and Details DIRECTIONS FOR INSTALLATION OF LEGS OR PEDESTAL: (Stove must be cooled and all ashes cleaned out) * Remove bricks,...

27 TROUBLE-SHOOTING GUIDE WARNING: TO AVOID ELECTRICAL SHOCK ALWAYS DISCONNECT THE UNIT FROM THE POWER SOURCE BEFORE ATTEMPTING ANY REPAIR. IF THIS GUIDE DOES NOT CORRECT THE PROBLEM CALL YOUR LOCAL DEALER OR OUR CUSTOMER SERVICE AT 1-800-245-6489. Problem Cause Solution 1. Auger not turning 1. Loos...

28 TROUBLE SHOOTING (Unit must be OFF, unplugged and cool before any maintenance) PROBLEM CAUSE: Too rich air/fuel mixture Fire burns with a lazy, orange flame and/or fuel builds up in the firepot. Glass may become dirty. Flue or intake is restricted. Make sure glass door is shut and sealed tightly....

29 Have this information on hand if you phone the factory or your dealer regarding this product. Retain for your files: Model Number __________________________ Date of Purchase ________________________ Date of Manufacture _________________ Serial #_____________________ LIMITED 5 YEAR WARRANTY FROM T...

31 WARRANTY REGISTRATION for England’s Stove Works Purchased by (Name) ______________________________________________ Address _________________________________________________________ City ________________________ State __________ Zip _________________ Telephone _____________________________________...